jack points Seat Alhambra 2010 Owner's Manual

Trailer towing 266
xThe maximum drawbar load is used.
xThe trailer must have a fixed drawbar.
xTrailers with brakes must be equipped with a mechanical inertia brake.
WARNING
Do not let the extra safety afforded by the stabilisation system tempt you
into taking any risks when driving.
xAdjust your speed and driving style to visibility, road, traffic and
weather conditions.
xIf the road surface is slippery, take care when accelerating.
xWhen a system is operating, lift your foot off the accelerator.
WARNING
It is possible that the combination stabilisation system does not correctly
recognised all driving situations.
xIt is possible that the stabilisation system does not detect snaking of a
light trailer and thus does not intervene.
xWhen driving on slippery ground, the trailer could jack-knife despite
the stabilisation system.
xTrailers with a high centre of gravity may even tip over before they start
to rock sideways.
xIf a trailer is not used at the trailer socket is connected (for example,
installation of a bicycle carrier with lights), repeated automatic braking
may occur in extreme driving conditions.
Retrofitting a tow hitch
Fig. 164 Measurements and attachments to retrofit a tow hitch.
SEAT recommends visiting a specialist workshop to retrofit a tow hitch. For
example, it may be necessary to adjust the cooling system or to include
thermal plates. SEAT recommends visiting a qualified workshop.
In any case, the separation distances must be observed when fitting a tow
hitch. The distance between the centre of the tow hitch ball and the road
surface Ÿfig. 164 must never be lower than that indicated. This also
applies when the vehicle is fully laden, including maximum drawbar load.
Separation distances Ÿfig. 164:
Attachment points.
1,040 mm (41 inches)
74 mm (3 inches)
364 mm (14 inches)
AD
AA
AB
AC
AD

Accessories, parts replacement and modifications291
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Jacking points for raising vehicle
Always use the jacking points indicated in the figures Ÿfig. 167 and
Ÿfig. 168 when raising the vehicle. If the vehicle is not lifted at these points,
it could be seriously damaged Ÿ or lead to serious injury Ÿ.The vehicle should not be lifted using lifting platforms with lift pads
containing fluid.
When raising a vehicle using a platform or jack, a series of precautionary
measures are required. Never raise the vehicle with a lifting platform or jack
unless you have received training in how to do so and know how to lift the
vehicle safely.
Notes on raising the vehicle with a jack Ÿpage 342.
WARNING
The improper use of the lifting platform or the jack when raising the vehicle
may result in accidents or serious injury.
xBefore raising the vehicle, please observe the manufacturer's instruc-
tions for the platform or jack, and the legal requirements, where appli-
cable.
xThere should not be anyone inside the vehicle when it is being raised or
once it is in the air.
xOnly use the jacking points indicated in the figures Ÿfig. 167 and
Ÿfig. 168 when raising the vehicle. If the vehicle is not lifted at the indi-
cated points, it may fall from the platform while the engine or gearbox is
being dismounted, for example.
xThe jacking points should be centrally aligned and firmly positioned on
the platform support plates.
xNever start the engine when the vehicle is raised! The vehicle may fall
from the platform due to the engine vibrations.
xIf it is necessary to work underneath the vehicle while it is raised, you
should check that the supporting stands have an adequate load capacity.
xNever climb onto the lifting platform.
xAlways make sure that the weight of the vehicle does not exceed the
lifting platform load capacity.
Fig. 167 Front jacking
points for raising vehicle
with lifting platform or
jack.
Fig. 168 Rear jacking
points for raising vehicle
with lifting platform or
jack.

Wheels and tyres 342
Raising the vehicle with the jack
The jack may be applied only at the jacking points shown (marks on chassis)
Ÿfig. 192. The mark indicates the jacking points below the vehicle. The jacking points are on the ribs behind the front edges Ÿfig. 193. Always the
relevant jacking point for the wheel to be changed Ÿ.
Fig. 192 Jack position
points
Fig. 193 : jack mounted on the left front part of the
vehicle : jack mounted on the left rear part of the
vehicle.AAAB

Wheels and tyres343
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a Raise the vehicle using only the designated jacking points.
Check list
For your own safety and that of other passengers, the following points should
be observed in the order given Ÿ:
1. Select a suitable flat and firm surface for raising the vehicle.
2. Switch off the engine, engage a gear (manual gearbox) or place the
selector lever in position P Ÿpage 201 and turn on the electronic
parking brake Ÿpage 210.
3. When towing a trailer: unhook the trailer from the towing vehicle and
park it correctly.
4. Loosen the wheel bolts on the wheel to be changed Ÿpage 340.
5. Look below the vehicle for the jacking point Ÿpage 342, fig. 192
closest to the tyre which has to be changed.
6. Raise the jack with the handle until it can be inserted below the jacking
point.
7. Ensure that the foot of the jack is firmly on the ground and that it is
placed immediately below the lifting point on the vehicle Ÿpage 342,
fig. 193.
8. Straighten the jack and continue raising it using the handle until the claw
holds the vertical reinforcement beneath the vehicle Ÿpage 342,
fig. 193.
9. Raise the vehicle until the wheel is clear of the ground.
WARNING
If the vehicle is not correctly raised, it could fall off the jack causing serious
injury. Please observe the following rules to minimise the risk of injury:
xYou should only use a jack approved by SEAT for your vehicle. Other
jacks, even those approved for other SEAT models, might slip out of place.
xThe ground should be firm and flat. If the ground is sloped or soft then
the vehicle could slip and fall off the jack. If necessary, support the jack on
a wide solid base.
xIf the ground is slippery (for example, on tiles), place a non-slip surface
(for example a floor mat) beneath the jack to avoid slipping.
xOnly fit the jack at the prescribed jacking points. The claw of the jack
should grip the reinforcement nerve on the underbody Ÿpage 342,
fig. 193.
xYou should never have any limbs beneath a raised vehicle which is only
supported by a jack.
xIf you have to work underneath the vehicle, you must use suitable
stands additionally to support the vehicle, there is a risk of accident!.
xNever raise the vehicle if it is tilting to one side or the engine is running.
xNever start the engine when the vehicle is raised. The vehicle may come
loose from the jack due to the engine vibrations.
WARNING
Failure to follow the checklist prepared for your own safety could lead to
accidents and severe injuries.
xAlways complete the operations given in the checklist and observe the
general rules of safety.
WARNING (continued)