ABS Seat Exeo 2008 Owner's Guide

If and when261
Safety First
Operating instructions
Practical tips
Te c h n i c a l D a t a
Changing the side light bulb
The procedure for changing the bulbs on the front
passenger's side is the same as on the driver's side.
– Switch off the ignition and the lights.
– Raise the bonnet.
– Move the brace ⇒fig. 205 in the direction of the arrow and
remove the rigid cover, separating the brace side and then
removing the two tabs from the other end of the cover.
– Remove the bulb holder by pulling on the grip ⇒fig. 206 (it can
also be removed by pulling on the bulb holder wires).
– Separate the bulb from the bulb holder by pulling both pieces anti-clockwise.
– Fit the new bulb by pressing on the bulb holder.
– Insert the bulb into the socket and press on the bulb holder grip.
– Fit the cover, first inserting the side tabs and then closing the cover and the brace. Make sure that the gasket sits well on the
casing cover during the operation.
– Check whether the new bulb is working.Changing the xenon bulbThe procedure for changing the bulbs on the front passenger's side is the
same as on the driver's side.
WARNING
This type of bulb should be changed at a qualified workshop.
Fig. 205 Side lightFig. 206 Side light
A1
Exeo_EN.book Seite 261 Freitag, 17. Oktober 2008 11:24 11

If and when263
Safety First
Operating instructions
Practical tips
Te c h n i c a l D a t a
A special retaining screw is used to secure and guide the rear light.
– Check which of the bulbs is defective.
– Open the tailgate.
– Take the screwdriver out of the vehicle's tool kit ⇒ page 236.
– Use the flat-blade side of the reversible screwdriver insert.
– Prise open the cover at the slot with the screwdriver ⇒page 262,
fig. 208 .
– Use the screwdriver to loosen the screw (arrow) located behind the cover.
– Gradually ease the rear li ght out of the mounting (⇒page 262,
fig. 209 positions and ) by pulling alternately in positions and .
– Remove the bulb holder ⇒page 263.
CautionTake care when removing the rear light to make sure there is no damage to
the paintwork or any of its components.
Note
Make sure you have a soft cloth ready to place under the glass on the rear
light, to avoid any scratches.
Removing the bulb holder
When changing a bulb, you must first remove the bulb holder.There are three securing tabs on the inside of the rear light.
– Release the retaining tabs ⇒fig. 210 .
– Take out the bulb holder.
– Change the defective bulb ⇒page 264.
A1
A2
A3
A4
A1
A2
Fig. 210 Retaining tabs
on reverse side of rear
light
AA
Exeo_EN.book Seite 263 Freitag, 17. Oktober 2008 11:24 11

If and when267
Safety First
Operating instructions
Practical tips
Te c h n i c a l D a t a
You can access the bulb holder for the inner rear lights via the inside
of the tailgate.
– Check which of the bulbs is defective.
– Take the screwdriver out of the vehicle's tool kit ⇒ page 236.
– Insert the screwdriver into the opening in the cover from the top ⇒page 266, fig. 215 and detach the cover.
– Press on the tabs ⇒ page 266, fig. 216 in the direction of the
arrows and remove the bulb holder by pulling in the direction of
the arrow .
– Change the bulbs ⇒page 267.Changing the bulbs
All bulbs can be changed easily in the bulb holder.
The bulbs are secured with a bayonet fastener. The table below
gives an overview of the bulb positions.
– Lightly press the defective bulb into the bulb holder, then turn it
to the left and remove it.
– Fit the new bulb, pressing it into the bulb holder and turn it to the right as far as it will go.
– Use a cloth to remove any fingerprints from the glass part of the bulb.
– Check whether the new bulb is working.
– Re-install the bulb holder ⇒page 267.Position of the bulbsFitting the bulb holder
The bulb holder is easy to fit.– Check that the seal is seated correctly on the bulb holder.
– Position the bulb holder on the rear light and align it so that it is
securely seated.
– Press the bulb holder into the rear light until it engages.
AA
AB
Fig. 217 Position of the
bulbs in the bulb holder.
Example: Rear lights in
the tailgate
Pos. ⇒ fig. 217
Bulb function
A
Reversing light
B
Rear light and
rear fog light
Exeo_EN.book Seite 267 Freitag, 17. Oktober 2008 11:24 11

If and when
268
– Fit the cover back in the interior trim so that it engages.
– Put the screwdriver back into the tool kit.
– Make sure that all bulbs for the rear lights are working.Side indicators– Press the indicator to the left or to the right to remove the lamp.
– Remove the lamp holder from the indicator.
– Remove the failed glass bulb and replace with a new bulb.
– Insert the lamp holder in the indicator guide until it clicks into place. – First place the indicator in the opening in the bodywork, fixing
the tabs ⇒fig. 218 , arrow .
– Insert the bulb as shown by the arrow ⇒fig. 218.
Fig. 218 Side indicator
A1
A2
Exeo_EN.book Seite 268 Freitag, 17. Oktober 2008 11:24 11