change time Seat Leon 5D 2010 MEDIA SYSTEM 2.2

Navigation65
Visual recommendations on the mapWhen route guidance starts, the system automatically switches to the map
view ⇒fig. 65. The red
9 symbol indicates the vehicle's position and heading
⇒fig. 65 . If
the vehicle position symbol
9 remains in the same position and the map
view freezes, it is currently not possible to determine the vehicle's position,
e.g. in a multi-storey car park.
During route guidance the navigation route is shown as a blue line. Sections
closed to traffic either manually or due to TMC messages advising of traffic
congestion ⇒page 70 are shown in colour on the calculated route.
The next road to take is displayed in the top line of the screen.
After a few seconds, the function buttons disappear from the bottom line of
the screen to display more information on the route ⇒fig. 66.
•Briefly press the bottom-right or bottom-left area of the screen to display
the function buttons again ⇒ fig. 65.•Pressing the unit button switches between the Navigation main
menu and the map view.
When the function buttons are hidden, the current street and information
about the journey length are displayed on the bottom line of the screen
⇒ fig. 66 .: Remaining distance to the destination.: Expected time of arrival or travelling time ⇒page 73.
Shortly before you reach a turning point, a turning arrow appears, indicating
the direction to turn. The distance to the turning point is also displayed below
it.
Changing the map scale (Autozoom)
The “Autozoom” function is enabled for the map view by default. This means
that the map view automatically zooms in and out: Small scale on motorways.
Large scale in urban areas.•Turn the setting knob ⇒page 8, fig. 1 to manually change the scale
of the map for a few seconds. Turn the knob clockwise to zoom in. Turn the
knob anticlockwise to zoom out.
Fig. 65 Map view during
route guidance with the
function buttons
displayed.Fig. 66 Map view during
route guidance.
NAV
A10
MediaSystem2.1_EN.book Seite 65 Donnerstag, 29. April 2010 4:18 16

Navigation69
The route list contains the names or designations of roads to be driven on
before each turning point. These are referred to below as “route sections”. All
route sections to be passed up to the next destination are displayed.
The list also shows the distance to be travelled along each route section and
the expected time required to reach the next turning point.•Turn the setting knob ⇒page 8, fig. 1 to view the route list.•Press the setting knob or Details function button to obtain more informa-
tion about a marked section in an additional information window.•Press the unit button to close the information window.
Display sections of route
The arrow
b behind an entr y in the route list indicates that more sections can
be displayed.
•Select the entry with the arrow
b by turning the setting knob and display
the sections of the route by pressing “Display”. The arrow changes to
a.
•Press the entry with the arrow
a to hide the sections of the route again.
Manually excluding sections in the route listThe sections of the journey which are marked can be excluded individually or
all together from the calculation in the route lists. Only one exclusion may be
entered at a time.•Displaying the route list ⇒ page 68.•Turn the setting knob ⇒page 8, fig. 1 to mark the first route section
of the stretch of route to be excluded.•Press the function button.
The item is marked as excluded and the function button changes to . If, instead of the button , appears in the route list, this
means that the section has already been excluded.
•Select the route section of the stretch of route you wish to exclude and
press the function button.
If the button is not active, the section to be excluded is too long.
(Max) is displayed on the bottom line of the screen after the excluded
distance.•Shorten the section of route to be excluded until the word (Max) disap-
pears and it is possible to select the function button. At the same
time, display partial sections of the route within a section of the route
⇒ page 69.
When an exclusion has been entered, the route list closes.
Route guidance will start again when the navigation system has calculated an
alternative route to the excluded section.
Re-opening a section•Press the unit button in any of the navigation menus (except SETUP).•In the information window , press the function button.•Press the function button in the pop-up window.•Alternatively:open the route list and press the function button.Note
Information on entering an exclusion starting from the current vehicle posi-
tion ⇒page 70.
Note
The excluded route section is displayed on the map ⇒page 65.
A10

A10
Exclude
Exclude to
Exclude to
Re-open
Exclude to
Exclude to
Exclude to
º
Route
Re-open section
Re-open
MediaSystem2.1_EN.book Seite 69 Donnerstag, 29. April 2010 4:18 16

Navigation73
Ending demonstration mode
A s a ge ne ral r ule , th e D em o m od e sh ould b e s wi tche d of f a f ter use , o the r wis e
you will always have to select between virtual navigation or normal naviga-
tion before starting navigation to a destination.
Normally, the demonstration mode automatically ends on completion of the
route guidance programme or when a new navigation destination (not stop-
over) is entered. When the vehicle starts to move, or when the unit is switched
off, the demonstration mode ends.
If necessary, switch off the demonstration mode in the navigation setup
menu.•Press the unit button in one of the navigation menus.•Untick the checkbox for the function button.Setup menu Navigation
Press the unit button from any navigation menu to open the
Navigation setup menu ⇒ fig. 74 .
SETUP
’Demo mode
Fig. 74 Navigation setup
menu.
Function button: Result
: ⇒ page 63.
: Turn the setting knob ⇒page 8, fig. 1 to adjust
the volume of navigation announcements. To switch off, turn the knob to
the left until Off is displayed.
The volume of the navigation announcements can also be controlled from
the general volume settings ⇒page 87.
: the map mode changes from daytime to night-time view
as the dipped headlights are switched on.
: the map view remains in daytime mode (bright).: the map view remains in night-time mode (dark).
Fig. 75 Navigation setup
menu.
SETUP
Route optionsAnnouncement volume
A10
Day / night
AutomaticDayNight
MediaSystem2.1_EN.book Seite 73 Donnerstag, 29. April 2010 4:18 16

Telephone control (Phone)
82•Press the function button.•Enter the name you are searching for in the input window.
Each time you enter a character, the sequence of characters in the input line
is automatically completed with a name that is in the address book.
If no name is offered when all the characters have been entered, there is no
entry in the address book corresponding to the sequence of characters you
have entered.•Delete characters in the line of data until a name is suggested.
Both upper and lower case are accepted when searching for an entry in the
address book.•Press the function button to select the entry in the address book
when you have found it.•Alternatively: press the right unit button to select the entry in the list,
when you have found it.•Press the selected address book entry to make a call.•Alternatively: press the setting knob ⇒page 8, fig. 1 to make the
call.Displaying and editing the phone numberA telephone number stored in the address book or in a call list can be
changed before you dial it.
Displaying and changing telephone numbers via an input window•Select the phone number and press the function button.•Press the function button to view the number in the input window.
The phone number can be changed here or reproduced as a DTMF sequence.
After you have changed the number, you can dial it by pressing the function
key . The changes
are not saved permanently in the address book. The modified
phone number can be viewed in the call list Numbers dialled after a call has
been made.
Call listsAll the call lists in the mobile phone memory can be consulted using the radio
and navigation system phone control system. The call lists give all the calls
made using the mobile phone.
If the phone accepts the handsfree profile 1.5 , calls not made through the
radio and navigation phone control system will also be shown.
Missed calls
The call list gives all missed and unanswered calls.
Numbers dialled
The call list gives all the phone numbers selected through the mobile phone
and through the radio and navigation phone control system.
SearchOK
A10
Details
Edit

Fig. 81 Call list.
MediaSystem2.1_EN.book Seite 82 Donnerstag, 29. April 2010 4:18 16

Settings (SETUP)89
Note
The system of units used in the navigation menu (metric or imperial) is set on
the instrument panel.
: The keyboard in input windows has the usual computer layout.: Change display settings.
: press to select the screen brightness setting.: changes the map view.: the map view changes when the dipped beams are
switched on.
: the map view remains in daytime mode (bright).: the map view remains in night-time mode (dark).
: Switch the confirmation tone for pressing a function
button on or off.
: restore the unit to its original factory settings.
, , Changes to the air conditioning are displayed on the
screen for approximately 3, 5 or 10 seconds.: Changes to the air conditioning settings are not displayed on the
screen.
: switch time display on or off ⇒page 11.
Function button: ResultQWERTYScreenBrightnessDay/NightAutomaticDayNightAcoustic feedbackFactory settingsAir conditioning announcements3s
5s
10 s
OffTime display
MediaSystem2.1_EN.book Seite 89 Donnerstag, 29. April 2010 4:18 16

SEAT S.A. is permanently concerned about continuous development of its types and models. For this reason we ask you to understand,
that at any given time, changes regarding shape, equipment and technique may take place on the car delivered. For this reason n o
right at all may derive based on the data, drawings and descriptions in this current handbook.
All texts, illustrations and standards in this handbook are based on the status of information at the time of printing. Except for error
or omissi on, the information included in the current han dbook is valid as of the date of closing print.
Re-printing, copying or translating, whether total or partial is not allowed unless SEAT allows it in written form.
SEAT reserves all rights in accordance with the "Copyright" Act.
All rights on changes are reserved.
This paper has been manufactured using bleached non-chlorine cellulose.
© SEAT S.A. - Reprint: 15.02.10
Portada ALTEA_interior.qxd:maquetación 30/3/10 12:16 Página 3