Seat Leon 5D 2010 Owner's manual

If and when259
Safety First
Operating Instructions
Practical Tips
Technical Specifications
Bulb changeGeneral notesBefore changing any bulb, first turn off the failed component.
Do not touch the bulb glass. Fingerprints vaporise in the heat, causing a
reduction in the bulb life and condensation on the mirror surface, thus
reducing efficiency.
A bulb should only be replaced by one of the sam e type. The type is inscribed
on the bulb, either on the glass part or on the base. It is highly recommended to keep a box of spare bulbs in the vehicle. At the
very least, the following spare bulbs, which are essential for road safety,
should be kept in the vehicle.
Main headlights
Dipped beam - H7
Main beam - H1
Position - W5W
Turn signal - PY21W
Xenon headlights
26)/adaptive*
Dipped and full beam - D1S
27)
Daylight - P21W SLL
Position - W5W
Turn signals - PY21W
Fog lights
Fog lights - HB4
Fixed tail light
Stop/Position - P21W
28)
Turn signal - P21W
23a)
Engine management
5
Engine management
10
Engine management
15
24
AKF, gearbox valve
10
25a)
ABS pump
40
26
Left lighting
30
27a)
Engine management
40
Engine management
50
28
Vaca n t
29a)
Electric windows (front and back)
50
Electric windows (front)
30
30
Ignition key
50
a)Ampere rating according to motorisationNumber
Consumer
Amps
26)On this type of headlight, the bulb changes must be made by the SEAT dealer, given
that complex elements must be removed from the vehicle and a reset must be made
on the automatic control system incorporated.27)The Xenon bulbs discharge 2.5 times the light flux and have an average lifespan of 5
times more than that of halogen bulbs, this means that, except due to unusual circum-
stances, there is no need to change the bulbs for the whole life of the vehicle.28)Electronically controlled single filament bulb for Stop/side bulbs. If the bulb blows it
will not work in either position or Stop.
Leon_EN.book Seite 259 Mittwoch, 1. September 2010 6:16 18

If and when
260Mobile tailgate light
Fog light (driver side) - P21W
Reverse (passenger side) - P21W
Position - W5W
Side turn signal
Side turn signal - W5W
Number plate light
Number plate light - C5W
Glove compartment lamp
Glove compartment lamp - W5W
Note
•Depending on weather conditions (cold or wet), the front lights, the fog
lights, the tail lights and the turn signals may be temporarily misted. This has
no influence on the useful life of the lighting system. By switching on the
lights, the area through which the beam of light is projected will quickly be
demisted. However, the edges may continue to be misted.•Please check at regular intervals that all lighting (especially the exterior
lighting) on your vehicle is functioning properly. This is not only in the interest
of your own safety, but also that of all other road users.•Due to the difficulty in accessing some of the bulbs, any replacement work
should be done by a SEAT dealer. However, the following is a description of
how to change the lamps except for the fog lights* and interior lamps.
Main headlight bulbs
Turn signal
Dipped beam headlights
Main beam headlights
Side lights
Fig. 163 Main headlight
bulbs
AAABACAD
Leon_EN.book Seite 260 Mittwoch, 1. September 2010 6:16 18

If and when261
Safety First
Operating Instructions
Practical Tips
Technical Specifications
Turn signal bulbs– Raise the bonnet.
– Rotate the bulb holder ⇒fig. 164 to the left and pull.
– Remove the bulb by pressing on the bulb holder and rotating at the same time to the left.
– Installation is done in the reverse order.
Dipped beam headlights– Raise the bonnet
Fig. 164 Turn signal
AA
Fig. 165 Dipped beam
headlightsFig. 166 Dipped beam
headlights
Leon_EN.book Seite 261 Mittwoch, 1. September 2010 6:16 18

If and when
262
– Remove the loops ⇒page 261, fig. 165 in the direction of
the arrow and remove the cover.
– Remove the connector ⇒page 261, fig. 166 from the bulb.
– Unclip the retainer spring ⇒page 261, fig. 166 pressing
inwards to the right.
– Remove the bulb and fit the replacement so that the rim of the attachment plate is on the reflector cut-out.Main beam headlights
– Raise the bonnet
– Remove the cover ⇒fig. 167 by pulling on this.
– Remove the connector ⇒fig. 168 from the bulb.
–Press the spring ⇒fig. 168 inwards and to the right.
– Extract the bulb and fit the replacement so that it sits correctly into the cut-out on the reflector.
– Installation is done in the reverse order.
A1
A2A3
Fig. 167 Main beam
headlights
Fig. 168 Main beam
headlights
AC
A1
A2
Leon_EN.book Seite 262 Mittwoch, 1. September 2010 6:16 18

If and when263
Safety First
Operating Instructions
Practical Tips
Technical Specifications
Side lights– Raise the bonnet.
– Remove the cover ⇒fig. 169 by pulling on this. – Extract the bulb holder
⇒fig. 170 outwards.
– Replace the bulb by pulling it out and inserting the replacement.
– Installation is done in the reverse order.
Ta i l l i g h t s•On the body
- Turn signal, side and brake light•On the tailgate
- Left side: side and fog lights.
- Right side: side and reverse.Turn signal, side and brake lights on the body
Fig. 169 Side lightsFig. 170 Side lights
AD
A1
Fig. 171 Turn signal, side
and brake lights on the
bodywork
Leon_EN.book Seite 263 Mittwoch, 1. September 2010 6:16 18

If and when
264
– Press on the side pin outwards and take out the bulb holder.
– Remove the blown bulb and change it for a new one.
– To refit follow the steps in reverse order, taking special care when fitting the bulb holder.Side light, fog light and reverse light on the tailgate
–Open the tailgate.
– Use a screwdriver to remove the cover ⇒fig. 172 .
– Take the bulbholder out pressi ng on the securing pins and
extract it outwards ⇒fig. 173 .
– Replace the faulty bulb, rotating it to the left and outwards.
– Installation is done in the reverse order.
Fig. 172 Lights on the
tailgate
Fig. 173 Removing the
bulb holder
Leon_EN.book Seite 264 Mittwoch, 1. September 2010 6:16 18

If and when265
Safety First
Operating Instructions
Practical Tips
Technical Specifications
Side turn signals– Press the turn signal on one of its sides to take it out.
– Remove the bulb holder from the turn signal.
– Remove the faulty bulb and replace with a new one.
– Insert the bulb holder in the turn signal guide until it clicks into
place.
– First place the turn signal in the opening in the bodywork, fixing the tabs ⇒ fig. 174, arrow .
– Insert the turn signal as shown by the arrow ⇒fig. 174 .
Luggage compartment lights– Remove the bulb by pressing on the inside edge of this -arrow-
using the flat side of a screwdriver ⇒fig. 175 .
Fig. 174 Side turn signal
A1
A2
Fig. 175 Luggage
compartment lightFig. 176 Luggage
compartment light
Leon_EN.book Seite 265 Mittwoch, 1. September 2010 6:16 18

If and when
266
– Press the bulb sideways and remove it from its housing ⇒page 265, fig. 176.
– Installation is done in the reverse order.Registration light
– To remove the light cover, unscrew the bolts ⇒fig. 177.
– Remove the bulb, moving it in the direction of the arrow and outwards ⇒fig. 178 .
– Installation is done in the reverse order.Glove compartment lamp*– Insert screwdriver above, between the light and the glove compartment.
– Carefully remove the light Next lift the light out sideways.
–Replace the bulb.
– Insert the light on the connector side, first underneath then push at the top until it clicks into place.
Fig. 177 Number plate
light
Fig. 178 Number plate
light
Leon_EN.book Seite 266 Mittwoch, 1. September 2010 6:16 18

If and when267
Safety First
Operating Instructions
Practical Tips
Technical Specifications
Sun visor light– Carefully remove the lamp, using the flat side of the screwdriver,
as shown in the figure ⇒fig. 180 . – Remove the bulb, moving it in the direction of the arrow and
outwards ⇒fig. 180 .
– Installation is done in the reverse order.
Jump-startingJump leads
The jump lead must have a su fficient wire cross section.If the engine fails to start because of a discharged battery, the battery can be
connected to the battery of another vehicle to start the engine.
Jump leads
Jump leads must comply with standard DIN 72553 (see manufacturer’s docu-
mentation). The wire cross section must be at least 25 mm
2 for petrol engines
and at least 35 mm
2 for diesel engines.
Note
•The vehicles must not touch each other, otherwise electricity could flow as
soon as the positive terminals are connected.•The discharged battery must be properly connected to the vehicle elec-
trical system.
Fig. 179 Removing sun
visor lightFig. 180 Removing sun
visor light
Leon_EN.book Seite 267 Mittwoch, 1. September 2010 6:16 18

If and when
268How to jump start: descriptionJump lead terminal connections
1. Switch off the ignition of both vehicles ⇒. 2. Connect one end of the
red jump lead to the positive terminal
⇒ fig. 181 or ⇒fig. 182 of the vehicle with the flat
battery .
3. Connect the other end of the red jump lead to the positive
terminal in the vehicle providing assistance .
4. On vehicles with no Start-Stop system , connect one end of the
black jump lead to the negative terminal in the vehicle
providing assistance ⇒fig. 181 .
5. On vehicles with the Start-Stop system , connect one end of the
black jump lead to a suitable ground terminal, to a solid metal
part bolted to the engine block or to the engine block itself
⇒ fig. 182 .
6. Connect the other end of the black jump lead to a solid metal
component bolted to the engine block or to the engine block
itself of the vehicle with the flat battery. Do not connect it to a
point near the battery .
7. Position the leads in such a way that they cannot come into contact with any moving parts in the engine compartment.
Starting
8. Start the engine of the vehicle with the boosting battery and let it run at idling speed.
9. Start the engine of the vehicle with the flat battery and wait one or two minutes until the engine is running.
Removing the jump leads
10. Before you remove the jump leads, switch off the headlights (if they are switched on).
Fig. 181 Diagram for
connecting jump leads if
the vehicle providing
assistance the current is
not fitted with the Start-
Stop system: flat battery and battery providing
current .AA
AB
Fig. 182 Diagram for
connecting jump leads if
the vehicle providing
assistance is fitted with
the Start-Stop system:
flat battery and
battery providing current .
AA
AB
A+
A+
AAA+
AB
A-
AB
AX
AX
AA
Leon_EN.book Seite 268 Mittwoch, 1. September 2010 6:16 18