display Seat Tarraco 2020 Owner's Guide

Start and driving
In the key there is a chip that automatically
deactiv at
es the electronic immobiliser.
The electronic immobiliser is automatically
activated when the key is outside the vehicle.
If the following message is shown on the in-
strument panel display: SAFE , the vehicle
cannot be started.
The engine can only be started using a genu-
ine SEAT key with its correct code. Note
A perfect operation of the vehicle is ensur-
ed if genuine SEAT k eys ar

e used.Emergency starting function
Fig. 162
On the right of the steering column:
emer gency st

art. If no valid key is detected inside the vehicle,
an emer
gency st

art-up will be required. The relevant message will appear in the dash
panel display. This may happen when, f

or ex-
ample, the vehicle key battery is very low:

Driving
Hybrid B (use the batt ery's char
ge)1)
This is the operating mode that allows you to
save most fuel.
The operating mode control unit tries to make
the most of the battery charge. For this pur-
pose, with active directions the navigation
data are also accessed.
In this operating mode, the electric motor and
the combustion engine share the work of
driving the vehicle.
In hybrid operating mode, the power from the
battery charge is used optimally. If route
guidance is activated, the vehicle may auton-
omously recharge the high-voltage battery
using the combustion engine.
Manual control of the battery charge
Manual control of the battery charge is only
possible in Hybrid operating mode. The op-
tion selected by the user is only valid until the
ignition is switched off or the vehicle is switch-
ed to Hybrid mode or E-MODE.
Press the function button  and use the sym-
bols , = and  to control the battery charge:
Pressing this symbol selects a higher
theoretical charge level. The vehicle
 tries to reach that new theoretical high-
volt
age battery charge level while driv-
ing. The vehicle is powered by the com-
bustion engine. If the combustion engine
has “excess” power, it is used to charge
the high-voltage battery. This option in-
creases fuel consumption. SEAT there-
fore recommends using the charging
socket to charge the high-voltage bat-
tery, whenever possible ››› page 320
.
The high-voltage battery charge level is
kept at around the current level while
driving. If you accelerate harder or in-
crease the vehicle speed, the combus-
tion engine starts up. When permitted by
the driver’s demand for acceleration and
the vehicle speed, the vehicle switches
back to electric mode.
Pressing this symbol selects a lower the-
oretical charge level. The vehicle only
uses the battery's charge when it is
above the selected theoretical charge
level. The rest is kept until the end of the
journey.
=
 Show the active operating mode
The operating mode activ
e at any given time
is displayed on the instrument cluster display,
e.g. B. WARNING
Switching to a different operating mode
whil e driving can distr

act you from traffic
conditions and cause accidents. Note
Information about the operating mode that
is curr ently activ

e is displayed on the in-
strument cluster display, along with the
charge level of the high-voltage battery. Troubleshooting
@
The E-MODE oper
ating mode is not
av
ailable
The indicator lamp lights up in white.
The E-MODE operating mode N
(driving in
electric mode) cannot be used temporarily
because one or more conditions are not met.

Driving
Automatic gearbox/DSG au-
t omatic gearbo
x*
Introduction Your vehicle is equipped with an electronical-
ly contr
oll

ed manual gearbox. Torque be-
tween the engine and the gearbox is trans-
mitted via two independent clutches. They
replace the torque converter found on con-
ventional automatic gearboxes and allow for
smooth, uninterrupted acceleration of the ve-
hicle.
The Tiptronic system allows the driver to
change gears manually ››› page 230,
Changing gear in Tiptronic mode*.
Control lamps 
It lights up green
The brake is not pressed.
T o sel

ect a gear range, press the brake pedal. 
Flashes green
The selector lever locking button is not engaged.
The v ehicl

e is prevented from moving forwards. En-
gage the selector lever lock. Selector lever positions
Fig. 166
Selector lever lock. Fig. 167
Selector lever lock (hybrid vehicles). The selector lever position is shown when the
corr
esponding sign lights up

. With the selec-
tor lever in the manual gearbox positions M, D
and S, the engaged gear is also shown on the
display. 
– Parking l
ock
When the lever is put in this position, the drive
wheels are locked. The lever must only be put
in P when the vehicle is stationary ››› .
T o put the l

ever in P or take it out of P , the
locking button must be pressed and held and
the brake pedal pressed simultaneously.
 – Reverse gear
Reverse gear must be engaged only when
the vehicle is stationary and the engine is
idling ››› .
T o mo

ve the lever to position R, the lock but-
ton must be pressed and held while pressing
the brake pedal at the same time. The reverse
lights come on when the lever is in the R posi-
tion with the ignition on.
 – Neutral
With the lever in this position, the gear is in
neutral.
Press the brake pedal to move the lever from
N to D/S when the vehicle is stationary or at
speeds below 3 km/h (2 mph) ››› .
 – P
ermanent f

orward drive position
The lever in the D/S position enables the
gears to be operated in normal mode (D) or
sport mode (S). To select Sport mode S,
move the lever backwards. Pushing the lever
again will select normal mode D. The
228

Start and driving
Driving with an automatic gearbox The gearbox changes gear ratios automati-
cally as the v
ehicl
e moves.
The engine can only start with the selector
lever in position P or N. At low temperatures,
below -10 °C (+14 °F), the engine can only
start with the selector lever in position P.
Driving down hills
Under certain circumstances it may be ad-
vantageous to use the Tiptronic mode to se-
lect the gear manually according to driving
conditions ››› .
St op/P

ark
On level ground, just use the lever to engage
position P. On slopes you should first apply
the parking brake and then set the lever to P.
This makes it easier to remove the lever from
position P when starting.
If the driver door is opened and the lever is
not in position P, the vehicle could move. The
following warning is displayed on the instru-
ment panel:

Driving
k
It lights up grey
Hill Descent Control is not active. The system is
s wit
ched on, but is not adjusting. Some control and warning lamps will light up
briefly when the ignition is s
wit

ched on to
check certain functions. They will switch off
after a few seconds. WARNING
Observe the safety warnings ››

› in Con-
tr ol and w
arning lamps on page 85. Description and operation
Hill Descent Control limits the speed on steep
descents by aut
omatically br

aking all four
wheels, both when moving forward and in re-
verse. As the anti-lock brake system remains
active, it prevents the wheels from locking. In
vehicles with manual transmission, the Hill
Descent Control adapts the theoretical
speed without slowing the engine below its
idling speed.
After starting the descent of a slope below
30 km/h (18 mph), speed is limited to a mini-
mum of 2 km/h (1 mph) and a maximum of
30 km/h (18 mph). When appropriate, the
driver may increase or decrease the speed
within the limit by pressing the accelerator or the brake. At this point the function is interrup-
ted and, if necessary, it is then r

eactivated.
Even so, it is imperative that the surface guar-
antees sufficient adhesion. For this reason,
the Hill Descent Control will not fulfil its func-
tion when, for example, descending a slope
with a frozen or slippery surface.
Hill Descent Control is available when the
dash panel display shows the message k .
Hill Descent Control automatically intervenes
if the following conditions are met:

Start and driving
sportier, more direct and noticeably more dy-
namic driving sensation.
St eering assist
This help assists the driv
er in critical situa-
tions. It recommends turning the steering
wheel to perform a corrective manoeuvre
(counter-steering), turning slightly to avoid
skidding ››› .
WARNING
Steering assist helps the driver in critical
sit uations. The driv

er is the person who has
to control the vehicle's steering at all times. Control lamp
v
It lights up red
Faulty steering.
Do not continue driving, st op the v

ehicle as soon as
possible and in a safe manner.
Take the vehicle to a specialised workshop and have
the fault repaired as soon as possible. v
It lights up yellow
Limited steering operation.
Driv e car

efully to a specialised workshop to have the
steering checked.
If the warning light does not come on again after re-
starting the engine and driving a short distance, it is
not necessary to check the steering.
OR: The 12-v olt batt
ery was disconnected and re-
connected.
Drive a short distance at 15-20 km / h (9-12 mph). v
It flashes yellow
The steering column is jammed.
When st opped, t

urn the steering wheel in both direc-
tions.
OR: The st eering column does not unlock or lock.
T
urn off the ignition and turn it on again. Consider the
messages shown on the instrument panel display.
Do not continue driving if the steering column re-
mains locked after switching on the ignition. Seek
specialist assistance. The control lamp should light up for a few
seconds when the ignition is s
wit

ched on. It
should go out once the engine is started. WARNING
Never ignore the warning lamps or messag-
es.

Driving
Engine
Depending on the pr ofil
e selected, the engine
responds more quickly or smoothly to the ac-
celerator being pressed. When the Eco pro-
file is selected, the Start-stop function is
activated.
In vehicles with automatic transmission, the
gear change timing is changed to put the
changes at higher or lower revolutions. The
Eco profile activates the Inertia function,
thereby reducing consumption. The rest of
the driving profiles will activate the inertia use
function when the selector lever is not in the S
position, depending on how the accelerator
pedal is released ››› page 233
. When the ve-
hicle is turned on again, the function is activa-
ted by default to reduce consumption.
With manual transmission, the Eco profile
changes the gear change recommendations
to facilitate more efficient driving.
Dynamic chassis control (DCC)*
DCC continuously adapts the shock absorb-
ers to the condition of the road and current
driving conditions, according to the pre-set
programme.
In the event of a fault in the DCC, the follow-
ing message is displayed on the instrument screen Fault: shock absorber regula-
tion
Steering
The po
wer steering varies its driving modes
and adapts to the profile selected, thus offer-
ing the best behaviour for each situation.
Air conditioning
The Climatronic* can operate in Eco mode
with particularly limited consumption.
Adaptive Cruise Control (ACC)*
Depending on the driving profile, the perform-
ance of the ACC varies, to allow more sporty
acceleration and braking or a more respect-
ful fuel consumption.
Electronic Stability Control (ESC)
In the Offroad and Snow driving profiles, the
electronic stability Control (ESC)
››› page 278 adjusts to adapt to the terrain.
In addition, hill descent control (HDC) is acti-
vated in the Offroad profile ››› page 236
.
PreCrash system
The PreCrash system adapts according to
the selected configuration. The Sport and
Offroad driving profiles have specific settings to adapt them to driving and terrain charac-
teristics
›
›› page 23
.
Setting the driving profile Fig. 170
Centre console: Driving Experience
butt on. Fig. 171
Centre console: S-BOOST button238

Driving
turning the Driving Experience button or se-
l
ect fr
om the infotainment display.

Driving
CCS switched on. The speed memory is
empt y.
The CCS is s
witched on. The set speed is
displayed in large figures.
Changing gear in CCS mode
The CCS decelerates as soon as the clutch
pedal is pressed, intervening again automati-
cally after a gear is engaged.
Travelling down hills with the CCS
If the CCS cannot maintain a constant vehi-
cle speed downhill, brake and change down
a gear if necessary. The GRA is temporarily
disabled by pressing the brake.
Automatic off
The GRA disconnects automatically or is
temporarily interrupted:

Driving
travelling in the same lane and direction. It
may not activ at
e in other hazard situations
››› .
Fr ont Assist is enabl

ed between 4 km/h (2.5
mph) and 250 km/h (156 mph). Depending
on a range of conditions, some of the func-
tions described below are omitted to optimize
the behaviour of the system.
Front Assist is a driving assistance function
that can never replace the driver’s atten-
tion.
Safety distance warning
If the system detects that you are driving too
close to the vehicle in front, it will warn the
driver with this indication on the instrument
panel display