ECO mode SKODA CITIGO 2015 1.G Funky Car Radio Manual

Code number
The code number can only be called up “online” via the ŠKODA system, as this
guarantees even more effective anti-theft protection. In this case you will have to call on a specialist 1)
garage.
Incorrect code number
If an incorrect code is confirmed after entry of the code, the procedure can be re-
peated once again . The number of attempts is shown in the bottom screen line.
If the code is entered incorrectly a second time, the unit will be blocked for ap- prox. one hour. It is only possible to enter the safety code again after one hourhas expired if both the device and the ignition have stayed turned on during thattime.
If two invalid attempts are then made again, the unit will be blocked again for an hour.
The cycle - two attempts, blocked for an hour - will continue to apply.
Note
The code is normally stored in the instrument cluster. This ensures that it is auto-
matically decoded (convenience coding). Manual input of the code is normally not necessary.
Device specification and operation
Equipment overview
Fig. 1
Equipment overview

- Setting up button
› for switching the equipment on and off (press)
› for volume adjustment of audio source currently being played (turn)
Settings knob
› for activating the Scan function
› for settings in the individual modes
› Changing to the previous/next title
RADIO
- Radio operation
MEDIA - MEDIA operation
TP - switches traffic programme on/off
MENU - Setting of the special functions
 and  - buttons for moving forwards/backwards
› RADIO-Mode
- for the selection of the stations from the preset list.
› MEDIA-Mode
- for the selection of the previous or following track.
› MENU-Mode
- for setting the setpoints of special functions
CD case 
- Eject a CD 
1234567891)
Explanation of terms
» Owner's Manual , chapter Foreword .
3General information

 - Sound settings
Function keys
› Save and select radio stations
› Enter code
AUX input - Attach an external audio source
Switching the unit on and off
›
To switch the device on and off, press setting button
1
.
After switching on the unit, the last audio source that was active before switch-
ing off will be played.
If the vehicle key is pulled out of the ignition lock while the unit is switched on,
the device will switch off automatically.
When the ignition is switched off, the system switches off automatically after ap-
prox. half an hour (discharge protection of the vehicle battery).

Volume setting
›
To increase the volume, turn button
1
clockwise.
›
To decrease the volume, turn button
1
counter-clockwise.
The change to the volume appears in the unit display.
If the volume is reduced to 0, the speakers are muted. The following symbol will
appear in the display 
.
CAUTION
High volumes can cause hearing damage.
Sound settings
By pressing the button again 
select the setting desired.
■ TRE - Treble setting
■ BAS - Bass setting
■ BAL - setting of the volume ratio between the left and the right side
■ FAD - setting of the volume ratio between the front and the rear
101112MENU mode
SCN (scan) function
Press menu button
2
or the MENU button and then the function button
SCN .
The auto-play function starts and plays each station in the current frequency
band for about five seconds.
Press the menu button
2
or the function button SCN again to stop automatic
playing of the radio station you are currently listening to.

Function AS
Press the MENU
button and then the function button
AS .
An automatic station finding is started during which the 6 stations with the
strongest signal in the memory level FM1 and/or AM1 are stored. AM1 nebo DA1.

UPD function
Press the MENU
button and then the function button
UPD
This starts an automatic update of the radio station and the stations with the strongest signal are re-stored at the FM1, AM1 or DA1 storage levels.

Setting special functions
Press the MENU
button and then the function button
SET .
■ SKM (SEEK MODE) - automatic station finding
■ ALL - stops the station finding at all available stations
■ PRESET - stops the station finding only at the stored stations
■ VOL - adjusts the volume when the device is turned on
■ GALA - speed-sensitive volume adjustment
■ DIS - sets the display backlight
■ PHONE - outputs telephone calls via the onboard loudspeakers
■ PDC - sets the reduction of the volume when the park distance control is active
■ PDC VOL ATTENU 0 - no volume limit
■ PDC VOL ATTENU 1 - medium level volume limit 
4General information

CD player
Using the system
Information on how to use a CD
Audio-CDs (CD-A) and MP3-CDs can be played in the internal drive.
Inserting the CD
Insert a CD, with the printed side facing up, into the CD slot
8
until it is automati-
cally drawn in.
The play function will start automatically.
When a CD is inserted, this will be indicated by the text “ CD-IN ” on the device
screen.
Taking out the CD
Press the 
button – the CD is ejected.
If the “ejected” CD is not taken out within 10 seconds, it will be retracted again for
safety reasons.
Buttons on the unit for controlling the current audio sources The arrow buttons on unit 
or  will always affect the currently heard audio
source, irrespective of the current menu used.

- pressing this button briefly within 2 seconds of playback takes you to the be-
ginning of the previous track or chapter, or after 2 seconds to the beginning of
the current title or chapter.

- pressing this button takes you to the start of the next track or chapter.
Playback of the previous or next track can also be selected by turning the menu
button
2
» Fig. 1 on page 3.
Changing between the audio sources
Press the MEDIA
button to select the audio source:
CD (internal CD drive) NAV
(connected MFP) or AUX .
WARNINGThe CD-player is a laser product. On the manufacturing date, this unit was
classified as a class 1 laser product in accordance with the national/interna-
tional standards DIN EN 60825-1: 2008-05 and DHHS Rules 21 CFR,
Subchapter J. The laser used in this class 1 laser product is so weak that there is no risk of danger when operated correctly. This product is designed such
that the laser is restricted to the inside of the unit. However, the installed la- ser could be classified in a higher class were the housing to be removed. Forthis reason, never remove the housing of the unit.
CAUTION
■ Never insert CDs with the designation “into the internal drive. Do not insert in
drives without a drawer ” or use Eco Discs.■
After pressing the button  there is a time delay of a few seconds before the
CD is ejected. During this time the lock in front of the CD slot is open.
■
Be sure to wait until the CD has been fully ejected before you try to insert a new
CD. Otherwise you can damage the drive inside the unit.
■
A dirty, mechanically damaged, unreadable or incorrectly inserted CD can cause
playback problems. The CD may not be playable or may jump because of this.
Check the CD and insert it properly into the unit. Should the problem persist , try
using another CD and visit a specialist garage if necessary.
■
If the internal temperature of the device is too high, no CDs will be accepted.
The unit switches into the last active operating mode.
■
Never use liquids such as gasoline, paint thinner or record cleaner to clean the
surface of the CD - this may cause damage.
■
Never expose the CD to direct sunlight!
■
Only write on the CD using appropriate pens.
■
Do not stick anything to the CD.
Note
■ Poor or unpaved road surfaces and severe vibrations may cause the CD to jump.■In cold weather or after rain showers, moisture (condensate) may deposit in the
unit. This can effect the CD jump or impair the play function. Wait until the mois-
ture has evaporated if this happens.■
If a CD is dirty, never clean it in a circular motion, but rather from the inside out.
Use a soft, lint-free cloth. For heavy stains, we recommend that you clean the CD with a commercially available CD cleaner and allow it to dry.
■
It is possible that CDs protected by copyright and home-made CD-R and CD-RW
will not be played back at all or only in certain circumstances. 
7CD player

■Please also note the additional information for MP3 mode .■The national copyright laws that apply in your country must be observed.■
The CD-player does not contain parts that need to be serviced or repaired. In
the case of a defective CD player, please visit a specialist garage.

Player operation
Press the MEDIA
button and then the
CD function key (internal CD drive), NAV
(connected MFP) or AUX » page 9 , Advice for dealing with external sources .
■ CD - changes over to an inserted CD
■ SCN - All tracks from the current audio source will be played for 10 seconds;
the scan function can also be started or stopped by briefly pressing the menu
button
2
.
■ SCAN CD - plays a track of a CD
■ SCAN FOLDER - plays a track in the selected folder
■ SCAN PLAYLIST - Plays a playlist (folder of selected tracks from each folder
stored on the CD); only appears when a playlist has been created on the CD
being played
■ MIX - plays all tracks in the current audio source in random order
■ The activated MIX function is underlined to highlight it.
■ MIX CD - plays the tracks on a CD in random order
■ MIX FOLDER - plays the tracks in the selected folder in random order
■ MIX PLAYLIST - Plays a playlist (folder of selected tracks from individual
folders that is stored on the CD) in random order; only appears when a play-
list has been created on the CD being played
■  - scrolls up in the folders
■  - scrolls down in the folders
■ INF - by pressing the INF function button again, additional information about
MP3 files can be selected in the display ■ TITLE - name of the track
■ ARTIST - name of the performer
■ ALBUM - name of the album
■ FILE - file
■ FOLDER - folder
■ SCR - Information about MP3 files with lengths that extend beyond the
screen area; by pressing this button, the entire text information is displayed step by step
■ NAV - Changes to the connected multi-function device
■ AUX - Changes to an external source connected to an AUX multimedia in-
put » page 9 , Advice for dealing with external sources

General information for MP3 operation
Requirements for the MP3 data and data carrier
› CD-ROM, CD-R, CD-RW with a capacity of 650 MB and 700 MB.
› The CDs must correspond to the ISO 9660 Level 2 standard as well as the Joliet
data system (single and multi-session).
› Data names must be no longer than 64 characters.
› The list structure is restricted to a depth of 8 list levels.
› The name of the artist, the album and the title of the MP3 file being played can
be shown, providing this information is available as an ID3 tag » page 8, Player
operation . The list and data name will be displayed if there is no ID3 tag.
› WMA data (
Windows Media Audio) can also be played even if the copyright is
additionally protected by the DRM procedure ( Digital Rights Management). Such
WMA data is not supported by the unit.
Bit rate (data flow per time unit)
› The system supports MP3 data with bit rates of 32 to 320 KB/s as well as MP3
data with variable bit rates.
› The indicated playing time data with variable bit rates is not reliable.

8CD player