SKODA FABIA 2011 2.G / 5J Owner's Manual

Connecting negative terminal and engine block
–
Attach one end 3 to the negative terminal of the battery supplying the power
B .
– Attach the other end 4 to a solid metal part which is connected firmly to the
engine block, or to the engine block itself ⇒  .
Starting engine
– Start the engine of the vehicle providing current and run the engine at idling
speed.
– Now start the engine of the vehicle with the discharged battery.
– Interrupt the attempt at starting an engine after 10 seconds if it does not start
right away and wait for about 30 seconds before repeating the attempt.
– Disconnect the cables in exactly the reverse order they were connected. WARNING
● The non-insulated parts of the terminal clamps must never make contact
with each other. In addition, the jump-start cable connected to the positive
terminal of the battery must not come into contact with electrically conduct-
ing parts of the vehicle - risk of short circuit!
● Do not affix the jump starting cables to the negative terminal of the dis-
charged battery. There is the risk of detonating gas seeping out the battery
being ignited by the strong spark which results from the engine being started.
● Do not affix the cable end 4 to parts of the fuel and brake system.
● Run the jump-start cables so that they cannot be caught by any rotating
parts in the engine compartment.
● Do not bend over the batteries - risk of caustic burns!
● The vent screws of the battery cells must be tightened firmly.
● Keep any sources of ignition (naked flame, smouldering cigarettes etc.)
away from the battery - risk of an explosion!
● Never jump-start the batteries which have a too low electrolyte level - risk
of explosion and caustic burns! Jump-starting on vehicles with the “START-STOP” system
Fig. 148 Jump-starting on vehicles with
the START-STOP system
One vehicles with the “START STOP” system, the negative cable of the charger
must never be connected directly to the negative pole of the vehicle battery, but
only to the engine earth ⇒ fig. 148. 
The vehicle General Vehicles with manual transmission can be towed in with a tow bar or a tow rope
or with the front or rear wheels raised.
Vehicles with automatic transmission can be towed in with a tow bar or a tow
rope or with the front wheels raised. If the vehicle is raised at rear, the automatic gearbox is damaged!
A tow bar is safest way of towing a vehicle and also minimizes any shocks. You
can use a tow rope only if a suitable tow bar is not available.
Refer to the following guidelines when towing:
Driver of the towing vehicle
– Release the clutch particularly gently when starting off or depress the acceler-
ator particularly gently if your vehicle is fitted with an automatic gearbox.
– On vehicles with manual transmission, only push down on the accelerator ped-
al once the rope is taught.
The maximum towing speed is 50 km/h. £ 179
Breakdown assistance Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical data

Driver of the towed vehicle
–
Switch the ignition on so that the steering wheel is not blocked and you can
also operate the turn signal lights, the headlight flasher, the windscreen wip-
ers and windscreen washer system.
– Take the vehicle out of gear or move the selector lever into position N if your
vehicle is fitted with an automatic gearbox.
Note that the brake servo unit and power steering only operate if the engine is
running. You will require significantly greater physical force to depress the brake
pedal and to steer the vehicle if the engine is not running.
Ensure that the tow rope is always kept taught. CAUTION
● Do not tow start the engine - danger of damaging the engine. On vehicles with
a catalytic converter, unburnt fuel may get into the catalytic converter where it
may ignite. This in turn may damage or destroy the catalytic converter. You can
use the battery of another vehicle as a jump-start aid ⇒ page 178, Jump-starting.
● If the gearbox of your vehicle no longer contains any oil because of a defect,
your vehicle must only be towed in with the driven wheels raised clear of the
ground, or on a special vehicle transporter or trailer.
● The vehicle must be transported on a special vehicle or trailer if it is not possi-
ble to tow in the vehicle in the way described or if the towing distance is greater
than 50 km.
● To protect both vehicles when tow-starting or towing, the tow rope should be
elastic. Thus one should only use plastic fibre rope or a rope made out of a similar-
ly elastic material.
● One should be constantly vigilant not to allow impermissibly high towing
forces or jerky loadings. There is always a risk of excessive stresses and damage
resulting at the points to which you attach the tow rope or tow bar when you at-
tempt to tow a vehicle which is not standing on a paved road.
● Attach the tow rope or the tow bar only to the towing eyes
provided for this
purpose ⇒ page 180,

Front towing eye and ⇒ page 181, Rear towing eye.Note
● We recommend a tow rope from the range of ŠKODA Original Accessories that
you can purchase from an authorised
ŠKODA Service Partner.
● Towing another vehicle requires a certain amount of practice. Both drivers
should be familiar with the particular points about towing a vehicle. Unskilled driv-
ers should not attempt to tow in another vehicle or to be towed in. ●
When towing, respect the national legal provisions, especially those which re-
late to the identification of the towing vehicle and the vehicle being towed.
● The tow rope must not be twisted as it may in certain circumstances result in
the front towing eye being unscrewed out of your vehicle. 
Front towing eye The towing eye is stored in the box of the vehicle tool kit.
Fig. 149 Front bumper: Cover/installing the towing eye
–
Press on the left half of the cover at the point of the arrow ⇒ 
fig. 149 - left.
– Pull the cover out of the front bumper.
– Screw in the towing eye by hand to the left up to the stop ⇒ fig. 149 - right. For
tightening, we recommend that you use for example the wheel wrench, the
lashing eye of another vehicle or a similar object which you can push through
the eye.
– In order to reinstall the cover after screwing out the towing eye, insert it in the
mounts and then press on the right side of the cover. The cover must engage
firmly. CAUTION
The towing eye must always be screwed in fully and firmly tightened, otherwise
the towing eye can tear when towing. 180
Breakdown assistance

Rear towing eye
Fig. 150 Rear towing eye
The rear towing eye is located below the rear bumper on the right ⇒ fig. 150
. 181
Breakdown assistance Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical data

Fuses and light bulbs
Electric fuses Replacing fuses in the dash panel Defect fuses must be replaced.
Fig. 151 Bottom side of the dash panel:
fuse cover
Individual electrical circuits are protected by fuses. The fuses are located on the
left side of the dash panel behind the safety cover.
– Switch the ignition off and also the electrical component affected.
– Carefully swivel the cover in the direction of arrow and pull it out ⇒ fig. 151.
– Find out which fuse belongs to the component which is not operating
⇒ page 183, Fuse assignment in the dash panel .
– Take the plastic clip out of its fixture in the fuse cover, insert it onto the re-
spective fuse and pull out this fuse.
– Defect fuses can be detected by their melted metal strips. Replace the defect
fuse by a new fuse of the same ampere number.
– Insert the fuse cover into the dash panel in such a way that the guide lugs are
guided into the openings of the dash panel and then lock them by pressing.
We recommend that you always have the small box of replacement fuses in your
vehicle. You can obtain a box of replacement fuses from the range of ŠKODA Origi-
nal Parts or from a specialist garage. Colour coding of fuses Colour Maximum amperage
light brown 5
brown 7,5
red 10
blue 15
yellow 20
white 25
green 30
WARNING
Read and observe the warning notes ⇒ page 153, Working in the engine com-
partment before working in the engine compartment. CAUTION
● Never attempt to “
repair” fuses and also do not replace them with a fuse of a
higher amperage - risk of fire! This may also cause damage at another part of the
electrical system.
● Have the electrical system checked as quickly as possible by a specialist ga-
rage if a newly inserted fuse blows again after a short time. Note
We recommend that you have these fuses replaced by a specialist garage. 182
Fuses and light bulbs

Fuse assignment in the dash panel
Fig. 152 Schematic representation of the fuse box for vehicles with left-hand steering/right-
hand steering
Certain electrical components are only standard on certain vehicle model versions
or only suppliable as optional equipment for certain models. No. Power consumer
1 S-contact
2 START - STOP
3 Instrument cluster, headlight range adjustment
4 ABS control unit
5 Petrol engine: Speed regulating system
6 Reversing light (manual gearbox)
7 Ignition
Engine control unit, automatic gearbox
8 Brake pedal switch, coolant fan
9 Operating controls for the heating, control unit for air conditioning sys-
tem, parking aid, control unit for cornering lights, coolant fan
10 The air conditioning system
11 Mirror adjustment
12 Control unit for trailer detection
13 Control unit for automatic gearbox
14 Motor for halogen projector headlights with cornering light function
15 Radio navigation system PDA
16 Electrohydraulic power steering No. Power consumer
17 START - STOP - radio
Daylight driving lights
18 Mirror heater
19 S-contact
20 Anti-theft alarm system
21 Reversing light, fog lights with the function “CORNER”
22 Operating controls for the heating, control unit for air conditioning sys-
tem, parking aid, mobile phone, instrument cluster, steering angle
sender, ESP, vehicle voltage control unit, multifunction steering wheel
23 Interior lighting, storage compartment and luggage compartment, side
lights
24 Central control unit of the vehicle
25 Seat heaters
26 Rear window wiper
27 Telephone preinstallation
28 Petrol engine: AKF valve, petrol engine: Control flap
29 Injection, water pump
30 Fuel pump
Ignition
Cruise control system, operation of PTC relay
31 Lambda probe
32 High pressure pump, pressure valve
33 Engine control unit
34 Engine control unit
Vacuum pump
35 Power supply of ignition lock
36 Main beam
37 Rear fog light
38 Fog lights
39 Blower
40 Heatable windscreen washing nozzles, windscreen cleaning system
41 Not assigned
42 Rear window heater
£ 183
Fuses and light bulbs Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical data

No. Power consumer
43 Horn
44 Front window wiper
45 Central control unit for convenience system
46 Engine control unit
Engine control unit
Fuel pump relay
Fuel pump control unit
47 Cigarette lighter, power socket in the luggage compartment
a)48 ABS, START-STOP - DC/DC converter ESP
49 Turn signal lights, brake lights
50 START-STOP - DC/DC converter infotainment
Radio
51 Electrical power window (front and rear) - left side
52 Electrical power window (front and rear) - right side
53 Parking light - left side
Electric sliding/tilting roof
54 START-STOP - instrument cluster
Anti-theft alarm system
55 Control unit for automatic gearbox DSG
56 Headlight cleaning system
Parking light - right side
57 Left low beam, headlight range adjustment
58 Low beam on the right
a)
If the engine is switched off already one electrical component which is connected can discharge the
battery. Replacing fuses at the battery (manual gearbox, automatic
gearbox DSG) Fig. 153 The battery: fuse cover
– Press together the interlocks of the fuse cover simultaneously in direction of
arrow A ⇒ fig. 153 and push out the cover in direction of arrow
B .
– Release the fixtures in the openings C using a flat screwdriver and fold the
cover upwards in direction of arrow D .
– Find out which fuse belongs to the component which is not operating.
– Defect fuses can be detected by their melted metal strips. Replace the defect
fuse by a new fuse of the same ampere number. WARNING
Read and observe the warning notes ⇒ page 153, Working in the engine com-
partment before working in the engine compartment. CAUTION
● Never attempt to “
repair” fuses and also do not replace them with a fuse of a
higher amperage - risk of fire! This may also cause damage at another part of the
electrical system.
● Have the electrical system checked as quickly as possible by a specialist ga-
rage if a newly inserted fuse blows again after a short time. Note
We recommend that you have these fuses replaced by a specialist garage. 184
Fuses and light bulbs

Fuse assignment at the battery (manual gearbox, automatic
gearbox DSG)
Fig. 154 Schematic representation of
fuse assignment at battery
Certain electrical components are only standard on certain vehicle model versions
or only suppliable as optional equipment for certain models. No. Power consumer
1 Generator
2 Not assigned
3 Interior
4 Electrical auxiliary heating system
5 Interior
6 Glow plugs, coolant fan
7 Electrohydraulic power steering
8 ABS or TCS or ESP
9 The radiator fan
10 Automatic gearbox
11 ABS or TCS or ESP
12 Central control unit
13 Electrical auxiliary heating system
CAUTION
Please refer to the following guidelines ⇒  in Replacing fuses at the battery
(manual gearbox, automatic gearbox DSG) on page 184 .Note
The fuses 1 - 7 can be replaced by a specialist garage. Replace fuses at the battery (automatic gearbox)
Fig. 155 The battery: Open the positive terminal cover/fuse cover
–
Open the positive terminal cover (+) ⇒ fig. 155 - left.
– Press onto the interlocks of the fuse covers A ⇒
 fig. 155 on the right and open
the covers.
– Press together the interlocks of the fuse cover B simultaneously and push
out the cover in the direction of the arrow.
– Find out which fuse belongs to the component which is not operating
⇒ page 186 ,
Fuse assignment at the battery (automatic gearbox).
– Defect fuses can be detected by their melted metal strips. Replace the defect
fuse by a new fuse of the same ampere number. WARNING
Read and observe the warning notes ⇒ page 153,
Working in the engine com-
partment before working in the engine compartment. CAUTION
● Never attempt to “
repair” fuses and also do not replace them with a fuse of a
higher amperage - risk of fire! This may also cause damage at another part of the
electrical system.
● Have the electrical system checked as quickly as possible by a specialist ga-
rage if a newly inserted fuse blows again after a short time. Note
● We recommend that you have these fuses replaced by a specialist garage.
● Some vehicles are only fitted with the cover B ⇒ fig. 155
on the right.  185
Fuses and light bulbs Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical data

Fuse assignment at the battery (automatic gearbox)
Fig. 156 Schematic representation of
fuse assignment at battery
Certain electrical components are only standard on certain vehicle model versions
or only suppliable as optional equipment for certain models. No. Power consumer
1 Generator
2 Interior
3 Electrical auxiliary heating system
4 ESP
5 Electrohydraulic power steering
6 Glow plugs
7 ESP
8 The radiator fan
9 The air conditioning system
10 ABS
11 Central control unit
12 Automatic gearbox
electrical auxiliary heating system
CAUTION
Please refer to the following guidelines ⇒  in Replace fuses at the battery (auto-
matic gearbox) on page 185. Bulbs
Replacing bulbs The relevant lamp must always be switched off before a light bulb is replaced.
Do not take hold of the glass bulb with naked fingers (even the smallest amount
of dirt reduces the working life of the light bulb). Use a clean cloth, serviette or
something similar.
Defect light bulbs should only be replaced with light bulbs of the same type. The
designation is located on the light socket or the glass bulb.
Changing certain bulbs is not something which you can do yourself, but requires
to be done by a specialist. Other parts of the vehicle must be removed in order to
change the light bulbs. This applies, in particular, to bulbs which can only be
reached from the engine compartment.
We therefore recommend that you have any bulbs changed by a specialist garage
or, in exceptional cases, by calling on other professional assistance.
Please note that the engine compartment is a hazardous area
⇒ page 153, Work-
ing in the engine compartment .
We recommend that you always have a small box of replacement bulbs in your ve-
hicle. You can obtain replacement bulbs from
ŠKODA Original Accessories or from
a specialist garage.
A stowage place for spare bulbs is located in the box in the spare wheel.
Vehicles with LED separate daytime running lights
In vehicles with LED separate daytime running lights, the bulbs are replaced by a
specialist garage.
Bulb - Overview Front headlight Halogen headlight Halogen projector head-
lights Low beam H4 LL H7 LL
Main beam H4 LL H7 LL
Parking lights W5W LL, LED
a)
/W5W BL LL Turn signals PY21W
£186
Fuses and light bulbs

Front headlight Halogen headlight Halogen projector head-
lights Fog lights H8/HB4
b) Daylight driving lights P21W, LED
a)
c) a)
Valid for RS vehicles with separate lights for daylight driving lights.
b) Valid for vehicles Scout.
c) Valid for Scout vehicles with separate lights for daylight driving lights. Rear light unit Bulb
Reversing light P21W
Turn signals PY21W
Brake lights P21W
Rear fog light P21W
Parking lights 2x W5W
Others Bulb
Side turn signal lights WY5W
Licence plate light C5W/T4W (5W)
3. Brake light LED
Interior lighting front / rear C10W
Reading lights W5W
Luggage compartment light W5W
Lighting in storage compartment W5W
WARNING
● Read and observe the warning notes ⇒  page 153, Working in the engine
compartment before working in the engine compartment.
● Bulbs H7 LL and H4 LL are pressurised and may burst when changing the
bulb - risk of injury!
● It is recommended to wear gloves and safety glasses when changing a
bulb. Note
This Owner's Manual only describes the replacement of bulbs where it is assumed
that no major complications will arise. Other light bulbs should be changed by your
specialist garage. Front headlight
Fig. 157 Fitting position of the bulbs: Halogen headlights/halogen projector headlights
Positions of the bulbs in the halogen headlamp
A - low beam, main beam and side lights
B - front turn signal light
Positions of the bulbs in the halogen projector headlight 1 - low beam/low and main beam
2 - Parking light/parking and main beam lights
3 - front turn signal light
WARNING
Read and observe the warning notes ⇒ page 153,
Working in the engine com-
partment before working in the engine compartment. 187
Fuses and light bulbs Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical data

Low beam and main beam (halogen headlights)
Fig. 158 Removing the light bulb for the
low beam and main beam light
– Remove the protective cap A ⇒
 fig. 157 .
– Pull off the connector from the lamp, release the sprung wire clamp and pull
out the lamp towards the rear ⇒ fig. 158 .
– Replace the lamp H4 LL, insert into the opening in the reflector (with the fixing
lugs in the recesses), secure with the sprung wire clamp, mount the connector
and position the protective cap.
– We recommend that you have the headlight setting checked by a Skoda Serv-
ice Partner after replacing the light bulb. 
Low beam and main beam/low beam (halogen projector
headlights) Fig. 159 Removing the light bulb for the
low beam and main beam light/low
beam light
– Remove the protective cap 1 ⇒
 fig. 157
. –
Turn the connector with the light bulb up to the stop towards the left
⇒ fig. 159 and remove.
– Replace the halogen lamp H7 LL, insert the connector with the new halogen
lamp and turn to the right up to the stop.
– Insert the protective cap.
– We recommend that you have the headlight setting checked by a Skoda Serv-
ice Partner after replacing the light bulb. 
Main beam (halogen projector headlights) Fig. 160 Removing the light bulb for the
main beam light
– Remove the protective cap 2 ⇒
 fig. 157
.
– Turn the connector with the light bulb up to the stop towards the left
⇒ fig. 160 and remove.
– Replace the halogen lamp H7 LL, insert the connector with the new halogen
lamp and turn to the right up to the stop.
– Insert the protective cap.
– We recommend that you have the headlight setting checked by a Skoda Serv-
ice Partner after replacing the light bulb. 
Turn signal light (at the front) –
Turn the socket B ⇒ fig. 157 or the socket
3 to the left and take it out to-
gether with the light bulb for the turn signal light.
– Replace the defective light bulb. £188
Fuses and light bulbs