air filter SSANGYONG MUSSO 2003 User Guide

1F3-8 OM600 ENGINE CONTROLS
Detach line downstream of air admission filter (13).Vacuum drops.
Faulty thermovalve
Fit the line onto air admission filter. Built up vacuum with vacuum pump. Detach the plug from air admission line. Vacuum drops.
Faulty filter with restriction.
Go to test step 2.
YES
NO
YES NO

1F3-28 OM600 ENGINE CONTROLS
Tools Required 001 589 65 09 00 Socket Wrench Insert000 589 00 68 00 Cleaning Set Repair Procedure
1. Clamp the nozzle holder (1) in a vice and remove the nozzletensioning nut (8). Notice Use protective jaws for clamping.
2. Disassemble the fuel injection nozzle.
Socket Wrench Insert 001 589 65 09 00
3. Clean the nozzle needle (6) and nozzle body (7) with an abradant.
4. Clean the nozzle seat with cleaning cutter.
Cleaning Set 000 589 00 68 00
5. Immerse nozzle needle (6) and nozzle body (7) in filtered diesel fuel. When the nozzle body is held vertical, the weight of the nozzle needle must cause it to slide down toward thenozzle needle seat.
6. Assemble the injection nozzle so that the tip of the thrust (4) pin is facing toward the nozzle holder.
Tightening Torque 80 Nm
Notice Nozzle needle (6) and nozzle body (7) should always be
replaced as a pair.

5A-122 AUTOMATIC TRANSMISSION
15. Install solenoid 6 plunger, spring and retaining pin.
16. Position the third feed ball (large nylon) in the valve bodyand install the solenoid 5 filter and the solenoid 6 filter.
Refer to figures 8.5 and 8.56.
17. Check the separator plate for burrs and damage. Repair or replace the separator plate as necessary.
18. Check the upper and lower valve body gaskets for damage. Replace the gaskets as necessary.
19. Install the lower valve body gasket on the lower valve body.
20. Install the reverse lockout valve, spring, plug and retainer plate. Ensure that the valve is correctly oriented. Refer to figure 8.57.
Figure 8.57 - Reverse Lockout Valve
21. Position the five nylon ball checks in the upper valve body.Refer to figure 8.48.
22. Fit the upper valve body gasket. Install the separator plate over the upper valve body.

7D-2 FATC-HAVC
Application
Size (WxHxT) Capacity
Type Description
650x339.2x22.0 11,000 Kcal/h
Parallel Flow
Condenser
Application
Material CapacityDesiccant Description
Aluminum 250cc
XH-9 or equivalent 35g
Receiver Drier
Application
Motor Type Motor Size Description
Magnetic
70 x
145
Blower Unit
Application
Replacement Description
Every 10,000 km (replace earlier if air pollution is heavy)
Air Filter
Application
Model
Type
Displacement (cc/rev.) Pulley Oil Description
FK-II(DKV 14C) Vane rotary 140.5
143.0
ZXL 200 PG (PAG Oil)
Compressor
Application
Heater Core Type Heating CapacityHeater Core Size (LxWxT) Description
2 - ROW
4,600 Kcal/h (AT 300CMH)
219.5 X 151.8 X 52
Heater Unit
Application
Type High (OFF)Low (ON) Description
Direct
OFF : 27±2Kgf/cm 2
, DIFF : 6±2Kgf/cm 2
OFF : 1.8±2Kgf/cm 2
, ON : 1.9±0.3Kgf/cm 2
Pressure Switch

7D-14 FATC-HAVCAir Filter; replace Notice
Replace earlier if air pollution is heavy. Replacement1.
1. Open the glove box and pull it inward to release the upper left and right locking portion. Notice Remove the glove box by unscrewing lower 2 screws, if
necessary.
2. Press the 2 filter cover holds and remove the air filter cover.
3. Remove the 2 air filters. NoticeFor installation, remember the installed direction of the air filter before removal.
Replacement Interval Every 10,000km