fuse SSANGYONG MUSSO 2003 User Guide

5D2-18 TRANSFER CASE (TOD) CODING
Coding Tool SCANNER
Connection of Coding Tool Construct SCANNER into diagnosis connector (20 pins) near fuse box in engine room as below figure.
1 Diagnosis Connector2 SCANNER
Notice Coding ; An input activity of data for the proper performance by matching specification, devices andsystem with control unit.

TRANSFER CASE (TOD) 5D2-21
DIAGNOSIS Malfunction interior TOD control unit ; fault code 1714
Phenomenon
1. When ignition “ON ”, “4WD CHECK ” lamp illuminates
continuously.
2. On diagnosis by SCAN-100, it displays fault code “1714 ”.
Cause ; Error of EEPROM checksum in TOD control unit
Test Stage / Contents
Result
Stage T est Contents and Procedure Specified Value
/Yes/No Countermeasure
Check power supply for TOD control unit. 1. Disconnect 30 pin connector from TOD control unit.
2. Ignition “ON ”.
3. Using multi-tester, measure voltage between pin 5(+)
and 17/18 (-). - Specified value - Measured value is within specified range ? 11-14 Vdc
Ye sNo Perform A2 stagePerform A3 stage
Check connection status in TOD control unit connector.
1. Check connection status.
- Is it connected exactly?
2. In case of mal-connection, connect tightly then perform the follows.
a. Delete fault code using Scan-100.
b. Ignition “OFF ”.
c. Ignition “ON ”.
d. Diagnose by Scan-100.
- Does it display fault code “1714 ”? Ye s
No
Ye s No
Check short of 10A fuse (fuse No.20).
1. Detach No.20 fuse from engine room fuse box.
2. Check the existence of short.
- Is fuse normal? Yes
No
Check ground of TOD control unit.
1. Ignition “ON ”.
2. Check voltage between 4/19 (+) pin and 17/18 (-)
using multi-tester (keep connection status).
- Specified value (battery is good)
- Measured value
3. Check short between 17/18 pin and body after disconnect 30 pin connector.
- Is resistance " "? 12Vdc (battery
voltage)
Ye s
No
Ye sNo
A1 A2 A3 A4
Perform A3 stage Perform A2 stage Perform A3 stage Normal system Perform A4 stage Replace fuse, then perform A1 stage Perform A4-3 stage Replace TOD controlunit Repair ground wiring Ground is O.K., perform A5 stage

TRANSFER CASE (TOD) 5D2-25
Error in electro - magnetic clutch : fault code “1721 ”, “1722 ”
Phenomenon
1. Upon diagnosis by SCAN-100, it displays on fault
codes “1721,1722 ”.
Cause
1. Defect in electro - magnetic clutch
2. Defect in connector or wiring
- Open or short from EMC to the supply : 1721
- Short EMC to ground : 1722
Ye sNo
C1
Ye sNo
Ye s
No
11-15Vdc Ye s
No
C2
Ye sNo
Test Stage / ContentsResult
Stage T est Contents and Procedure Specified Value
/Yes/No Countermeasure
Check relevant connector connection status.
1. Check relevant connector connection status with TOD
control unit.
- Does it connect correctly ?
2. Check connection status of speed sensor and clutch coil connector (7 pin) in transfer case.
- Does it connect correctly ?
3. In case of bad connection, connect it correctly then perform the follows :
a. Delete the memorized fault code in control unit withScan - 100.
b. Ignition “OFF ”.
c. Ignition “ON ”.
d. Diagnose by SCAN-100
- Does it display on fault codes “1721,1722 ” ?
Check supply voltage into electro-magnetic clutch.
1. Ignition “ON ”
2. Measure voltage between pin 4/19(+) and 17/18(-) in TOD control unit connector.
- Specified value
- Measured value is within specified range ?
3. If the specified value would not be measured, perform the follows :
a. Check battery voltage (charging condition)
b. Check open circuit on No.13 fuse (20A)
c. Check relevant wires.
- Is the above 3a, 3b, 3c normal ? Perform C1-2 stage Perform C1-3 stage Perform C2 stage Normal system
Perform C2 stage Perform C1-3 stage Perform C3 stage Perform C2-3 stage Perform C3 stage

Charging/ Replace battery
Replace fuse
Repair wires

FATC-HAVC 7D-19
Fault : intake (recirculation/fresh air) door inoperative
Remove the glove box.
Measure voltage between 6c terminal positive pole (+)
and bo dy (-).
Measured voltage is 12V.Check No. 24 fuse (15A) in the box.
Turn the ignitin switch OFF and disconnect harness of
the intake actuator.
Ye s No
Disconnect 3-pin connector of the intake mode actuator and turn the ignition switch to ON position.
6A
6B 6C
Check that it operates toward each direction after connecting the battery to the 6C terminal of intake
actuator and ground 6A & 6B to the body.6C 6B 6A
Wiring side connector
Actuator connector
Intake actuator is normal.
Ye s
Repair and replace the intake actuator.
No
Check intake actuator linkage and door for
proper operation and repair if necessary.Disconnect 20-pin connector from the airconditioner control unit.
Check current between the intake actuator (6A, 6B) and the airconditioner control unit (6,7).
Is there current?
Ye s
Repair open wire between the intake actuator and the control unit.
No
Replace the good control unit and re-check. If no fault, replace the control panel.
67

0.5YB

0.5LgR
+
-

7D-20 FATC-HAVC Fault : air flow does not change toward panel side.
8H
Remove the center panel of the instrument panel.
Measure voltage between 8I terminal positive pole (+) and body (-).
Measured voltage is 12V.Check No. 24 fuse (15A) in the fuse box.
Turn the ignition switch OFF and disconnect harness of
the mode actuator.
Ye sNo
Disconnect 8-pin connector of the mode actuator and turn the ignition switch to ON position.
Check that it operates toward each directions when
ground is connected to terminal (8J, 8H, 8F, 8D, 8B) of
the mode actuator alternatively.
Mode actuator
connector
Mode actuator is normal.
Ye s
Repair and replace the mode actuator.
No
Check the intake actuator linkage and door
for proper operation and repair if necessary.Disconnect 20-pin connector from the airconditioner control unit.
Check current between the mode actuator (8J, 8H, 8F,
8D, 8B) and the airconditioner control unit (11, 12, 13,14, 15).
Is there current?
Ye s
Repair open wire between the mode actuator and the control unit.
No
Replace the good control unit and re-check. If no fault, replace the control panel.
14 15
+
-
8
IWiring side connector
8I
8J 8H 8F 8D 8B 8A
Mode actuator connector Control unit connector
12 13
11
8B 8D 8F 8J

SECTION 9A
BODY WIRING SYSTEM
Schematic and Routing Diagrams . . . . . . . . 9A-2
Power Distribution . . . . . . . . . . . . . . . . . . . . . . 9A-2
Starting & Charging (Gasoline HFM) . . . . . . . 9A-3
Starting & Charging (Diesel) . . . . . . . . . . . . . . 9A-4
Fuse Box and Relay . . . . . . . . . . . . . . . . . . . 9A-5
Location of Connectors by
Wiring Harness . . . . . . . . . . . . . . . . . . . . . 9A-7
Main . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9A-7
Engine Room . . . . . . . . . . . . . . . . . . . . . . . . 9A-11
Floor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9A-13
Roof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9A-14
Driver's Door . . . . . . . . . . . . . . . . . . . . . . . . . 9A-15
Passenger's Door . . . . . . . . . . . . . . . . . . . . . 9A-15
TABLE OF CONTENTS
Caution: Disconnect the negative battery cable before removing or installing any electrical unit or when a tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable will help prevent personal injury and damage to the vehicle. The ignition must also be in LOCK unless otherwisenoted.
Rear Left Door . . . . . . . . . . . . . . . . . . . . . . . 9A-16
Rear Right Door . . . . . . . . . . . . . . . . . . . . . . 9A-16
Tail Gate . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9A-17
Semi Automatic Air Conditioner . . . . . . . . . . 9A-18
Full automatic Air Conditioner . . . . . . . . . . . . 9A-19
Gasoline Engine (MSE) . . . . . . . . . . . . . . . . 9A-20
Gasoline Engine (HFM) . . . . . . . . . . . . . . . . 9A-21
Diesel Engine . . . . . . . . . . . . . . . . . . . . . . . . 9A-22
Manual Transmission . . . . . . . . . . . . . . . . . . 9A-23
Automatic Transmission (BENZ) . . . . . . . . . . 9A-24
Automatic Transmission (BTRA) . . . . . . . . . . 9A-25
Driver's Seat . . . . . . . . . . . . . . . . . . . . . . . . . 9A-26

BODY WIRING SYSTEM 9A-5
FUSE BOX AND RELAY
1 Interior Relay Box
2 Interior Fuse Box
3 Engine Compartment Fuse and Relay Box

9A-6 BODY WIRING SYSTEM Engine Room Fuse (EF) and Relay Box1 Fuse (15A) : ABS, ABD
2 Fuse (20A) : Sun Roof
3 Fuse (10A) : Air Bag
4 Fuse (15A) : Audio, Clock, Out Side Mirror
5 Fuse (30A) : Cigarette lighter, Power Socket
6 Fuse (30A) : Heater
7 Fuse (15A) : Door Lock
8 Fuse (30A) : Rear Heated
9 Fuse (10A) : Audio, Buzzer, Chime, Clock
10 Fuse (30A) : Power Window
11 Fuse (10A) : Immobilizer
12 Fuse (20A) : T/C
13 Fuse (15A) : Interior Lamp
14 Fuse (15A) : Hazard Lamp
15 Fuse (15A) : Stop Lamp
16 Fuse (15A) : Turn signal Lamp, Head Lamp
17 Fuse (10A) : Back up Lamp
18 Fuse (15A) : Cluster, STICS
19 Fuse (15A) : A/T, Diagnosis
20 Fuse (15A) : Over Voltage Protection Relay (Gasolin Only)
21 Fuse (15A) : Seat Heater
22 Fuse (15A) : ECS
23 Fuse (15A) : Front Wiper & Washer
24 Fuse (10A) : Rear Wiper & Washer, A/C
25 Relay : Front Wiper 26 Relay : ABS Warning Lamp
27 Relay : Flasher Unit
28 Relay : Fuel Pump (Gasoline Only)
29 Relay : Shift Lock (A/T)
30 Relay : Clutch Interlock & Neutral
31 Relay : Sun Roof
32 Relay : A/T ‘B’ Interlock (MB A/T)
33 Relay : Power Window
34 Relay : Rear Fog Lamp
35 Relay : ECS
36 Relay : Compressor (Diesel E/G)
Condenser Fan (Gasoline E/G)
37 Relay : Condenser Fan
38 Relay : Air Conditioner
39 Fuse (10A) : Tail Lamp
40 Fuse (15A) : Head Lamp(LH)
41 Fuse (15A) : Head Lamp(RH)
42 Fuse (15A) : Front Fog Lamp
43 Fuse (10A) : Horn
44 Fuse (10A) : Compressor
45 Relay : Resistor with Diode (Gasoline E/G)
46 Relay : Front fog Lamp
47 Relay : Condenser Fan
48 Relay : Tail Lamp
49 Relay : Horn

9A-8 BODY WIRING SYSTEM1 Fuse Box
2 Door Lock Relay
3 Relay Box
3.1 Front Wiper Relay
3.2 ABS Warning Lamp Relay ....................................ABD 5.0
3.3 Flasher Unit
3.4 Fuel Pump Relay ................................................. Gasoline E/G
3.5 Shift Lock Relay ................................................... Automatic Transmission
3.6 Clutch Interlock & Neutral Relay ...........................Manual Transmission or Automatic Transmission
3.7 Sun Roof Relay
3.8 Automatic T ransmission ‘B’ Switch Interlock ....... Automatic Transmission
3.9 Power Window Relay
3.10 Rear Fog Lamp Relay .......................................... Rear Fog Lamp
3.11 ECS Relay 4 Defogger Relay
5 Ground 1
6 Roof Wiring Connector
7 Diode 1
8 Front Door Wiring Connector
9 Front Door Wiring Connector
10 Front Door Wiring Connector 11 Front Door Wiring Connector
12 Kick Down Relay .................................................. Automatic Transmission
13 Floor Wiring Connector
14 Floor Wiring Connector
15 Floor Wiring Connector
16 ABD Floor Wiring Connector ................................ABD 5.0
17 ECS Floor Wiring Connector
18 Rear Iper & Washer Switch
19 Clutch Switch ........................................................ Manual Transmission
19-1 Clutch Switch ........................................................ E32 Gasoline E/G with Manual Transmission
20 Stop Lamp Switch
21 Outside Mirror Switch
22 Ignition Switch
23 Multi Function Switch
24 Multi Function Switch
25 Black Out Switch .................................................. Black Out Lamp
26 Black out switch ................................................... Black Out Lamp
27 Joint Connector (Tail)
28 Joint Connector (Ignition)
29 Cluster
30 Cluster ................................................................. Automatic Transmission
31 Cluster
32 Cluster
33 4WD Switch .......................................................... Except TOD
33-1 4WD Switch .......................................................... TOD
3 4 Hazard Switch
35 Ground 2
36 Pedal Module ....................................................... Gasoline E/G with MSE ECU
37 Audio Switch
3 8 Immobilizer ........................................................... Crypto Type, Gasoline E/G with MSE ECU or Diesel E/G
39 Ignition Switch
40 Multi Function Switch
4 1 STICS
4 2 STICS
4 3 REKES ................................................................. Remote Keyless

MUSSO-SPORTS 1A-29
SUPPLEMENT
C101
W/H MAIN
12345 678910
11 12 13 14 15 16 17 18 19 20 21
Main - Engine Main - Engine Engine - MainMain - Floor Floor - FRAME FRAME - DECKMain Engine EngineMain Main Floor
C101 (21Pin, Colorless) C103 (2Pin, White) C108 (16Pin, Black)C206 (Colorless) C904 (10Pin, Black) C905 (12Pin, Black)S101 (Black) G101 G102G201 G204 G301
b. CONNECTOR IDENTIFICATION SYMBOL & PIN NUMBER POSITION
a. CONNECTOR INFORMATION
CONNECTOR(NUMBER)
CONNECTING. WIRING HARNESSCONNECTOR POSITION
Inside The Engine Room Fuse Block Inside The Engine Room Fuse Block Under The Coolant Reservoir Tank Inside Co-Driver Side Cowl PanelBehind The Left FRAME Behind The Left FRAME Inside The Engine Room Fuse BlockBehind The Left Lamp Behind The Right Head Lamp Right The I/P Fuse BlockUpper The ECM Center The Left 'B' Pillar
123 456
HEAD LAMP
MULTI-FUNCTION SWITCH
C1C2
C3 C4
B1 B2 B3 B4
B5 B6 B7 B8 B9
B10
A1 A2 A3 A4 A5 A6
A7 A8 A9
A10 A11 A12 A13 A14
123456789101112
29 30 31 32 33 34 35 36 37 38
28 13 2714261525162417231822
19 2021
39 43 40
44 45 46 4147
48
42
CLUSTER C108
W/H ENGINE
1234 5678
9 101112
13 14 15 16
C103
W/H MAIN
12
5678910 34
HAZARD
SWITCH
2
1
TAIL
LAMP
123 456
1234 5678
9 101112
C905
W/H DECK
5432
109871 6
C904
W/H FLOOR