weight SSANGYONG MUSSO 2003 User Guide

2E-4 TIRES AND WHEELSCOMPONENT LOCATOR
WHEEL AND TIRE
1 Wheel Bolts .................Steel Wheel : 80-120 Nm
.......................... Aluminium Wheel : 110-130 Nm
2 Steel Wheel
3 Aluminium Wheel
4 Tire
5 Steel Wheel Weight Balance
6 Hub Cap

2E-6 TIRES AND WHEELS
4. Tire pressure inspection. Tire pressure.
Check tread contact with road.
Notice
If underinflated, tire may come away from the wheel
during rapid steering.
An overinflated tire will cause a hard riding and uneven
wear.
Front & Rear
(P235/75R15) 2.1kg/cm (30PSI)
2
5. Wheel balance. Balance weights should be on each side. When the wheel
is out of balance or a tire has been repaired, be sure to balance the wheel again.
If total weight is over 150g, readjust the balance by
reinstalling the tire on the wheel.
Balance weight should not protrude from the wheel rim
over 3mm.
For aluminum wheel, use aluminum wheel balance weight
only.

TIRES AND WHEELS 2E-7
To correct unbalance, install equal weights 180 ° opposite
each other, one on the inside of the wheel and one on the outside, at the point of unbalance.
Balance Weight
6. Cautions for installation and removal. Clean the mounting surfaces of hub and wheel.
Do not apply grease or oil on the nuts and bolts (It will
cause looseness and poor tightening).
Using a jack, lift up the tire about 3cm from the ground.
Tighten nuts in a criss-cross pattern 2-3 times.10g
0.4oz
20g
0.7oz 30g
1.10oz 40g
1.40oz 50g
1.80oz 60g
2.1oz
Steel : 80 - 120Nm
Aluminium : 110 - 130NmTighten Torque

PROPELLER SHAFT 3C-7
Installation Procedure Clean the disassembled parts and replace them if damaged.
1. Align the alignment marks of the yoke and assemble thespider, bearing and snap ring.
2. Apply grease to the inner of the bearing cap of the needle roller bearing and assemble the needle roller.
Grease EP #2
6. Possible cause of vibration.
Drift away of balance weights.
Excessive runout of the propeller shaft.
Using normal bolts.
Excessive wear of the universal joint.
Sticks in sleeve joint.
Drive angle changes in universal joints or cross causes vibration and can be detected around 60~100 km/h.
5. Universal joint starting torque.
Starting Torque 3 - 8 kg

cm

AUTOMATIC TRANSMISSION 5A-105
21. Holding the cylinder horizontal, install the sleeve and clutchplate assembly into the cylinder, with the crest of one wave
of the washer In line with one of the holes in the outside of
the cylinder, until the sleeve contacts the C2 wave washer.
22. Check the C4 clutch pack clearance using special tool No. 0555-331900. Refer to figure 8.25. NoticeWith the C2 wave spring compressed, and the clutch Pack supporting a 2 k9 weight, the dimension from the undersideof the C2 pressure plate to the selective steel is to bebetween 1.4- 1.8 mm. If the clutch is to be gauged from the top of the pressure plate, then the dimension is to be the actual thickness of the pressure plate plus 1.4-1.8 mm.
23. Use selective plates to achieve the correct specification. If new friction plates are being fitted, remove the clutch packand soak the friction plates in ATF for a minimum of 5
minutes prior to reassembly. NoticeThe clutch pack clearance must be taken before the
elements are soaked in Automatic Transmission Fluid
(ATF).
24. Reassemble the sleeve and clutch pack into the cylinder. Observe the alignment of the wave washer to the hole in
the cylinder.
25. Install the C2 clutch plates in the cylinder in the following sequence:
Friction disc
Steel plate
Friction disc
Steel plate
Steel plate - 0574-000001, 0574-000003, 0574-000004, 0574-000005, 0574-000020,
0574-000021, or friction disc -0574-000002
Steel plate (selective)
Friction disc
Steel plate (selective)
Friction disc

5A-106 AUTOMATIC TRANSMISSION
29. Align the tangs and fit the nylon thrust washer onto theC4 hub. Refer to figure 8.27.
30. Align and fit the C4 hub to the C2 clutch and the OWC assembly.
31. Check the rotation of the C2 hub. While holding the C4 hub, the C2 hub should rotate in the clockwise
direction and lockup in the anti-clockwise direction when
viewed from the C2 hub. Refer to figure 8.27.
Figure 8.27 - C2 - Hub Rotation
32. Apply petroleum jelly to the No. 5 thrust bearing and fitit to the C4 hub. Refer to figure 8.19.
33. Remove the C2 clutch plates from the clutch cylinder.
34. Fit the thrust plate over the cylinder inner hub. Refer to figures 8.24 and 8.19.
35. Engage the C2/C4 clutch hub assembly in the C4 clutch plates.
36. Install the C2 clutch plates.
37. Install the C3 hub and secure it with the circlip, ensuring that the circlip is firmly seated in its groove.Refer to figure 8.32. Figure 8.26 - Typical C2 Clutch Pack Clearance
26. Check the clutch pack clearance using only the weight
from tool No.0555-331900. Refer to figure 8.26.NoticeWith the clutch pack supporting a 2 kg weight, the dimension from the C3 clutch hub locating step to the friction plate is to be between 0.80-1.05 mm.
27. Use selective plates to achieve the correct specification. If new friction plates are being fitted, remove the clutch
pack and soak the friction plates in ATF for a minimum
of 5 minutes prior to reassembly. NoticeThe clutch pack clearance must be taken before the
elements are soaked in ATF.
28. Lubricate and fit the 3-4 OWC and end caps to the C2 hub.

5A-108 AUTOMATIC TRANSMISSION
12. Install the circlip.
13. Check the C3 clutch clearance (refer to figure 8.29) usingspecial tool No.0555-331900 in the following manner (weight only).
a. Place the weight on the pressure plate and measure
the distance from the end of the cylinder to the top of the pressure plate.
b. Record this figure.
c. Remove the weight.
d. Lift the pressure plate up against the circlip and measure the distance from the end ofthe cylinder to the top of the pressure plate.
e. Record this figure.
f. Subtract the second reading from the first reading to obtain the clutch pack clearance.
NoticeWith the clutch pack supporting a weight of 2 kg, the clearance between the snap ring and the top of the pressure plate is to be between 1.20-1.45 mm.
14. If new friction plates are being fitted, remove the clutch pack and soak the friction elements in automatic
transmission fluid for a minimum of five minutes prior to
reassembly. NoticeThe clutch pack clearance must be taken before the elements are soaked in automatic transmission fluid. Figure 8.29 - Typical C3 Clutch Assembly
Clearance

5A-110 AUTOMATIC TRANSMISSION C1 Clutch Overdrive Shaft and Input Shaft Assembly Notice
1. Ensure that the snap rings are fitted correctly.
2. Check pistons for cracks, especially the C1 piston.
3. Do not mix clutch piston return springs.
4. If the C1/C2 clutch packs separate from the C3 clutch pack,make sure the No. 6 bearing doesn ’t drop out of the bearing
retainer.
To assemble the C1 clutch overdrive shaft and input shaft
assembly, proceed as follows:
1. Check the overdrive shaft grooves for any defect.
2. Coat the sealing rings, large and small, with petroleum jelly and fit them to the overdrive shaft. The sealing rings may
be held in place with a small amount of petroleum jelly.
3. Assemble the clutch plate and disc into the cylinder in the following sequence:
steel plate
friction disc
steel plate
friction disc
steel plate
steel plate - 0574-GOOGOl, 0574-000003, 0574-000004, 0574-000005, 0574-000020,
0574-000021, or friction disc -0574-000002
steel plate (selective)
friction disc
steel plate (selective)
friction disc
4. Check the clutch pack clearance using special tool No.0555- 331900. Refer to figure 8.31.Use selective plates to achieve the correct specification.NoticeThe clutch pack supporting a 2 kg weight, the dimension from the input shaft locating stop to the friction disc mustbe 0.70-0.90 mm.
5. If new friction plates are being fitted, remove the clutch pack and soak the friction elements in automatic transmission
fluid for a minimum of five minutes prior to assembly. NoticeThe clutch pack clearance must be taken before elements are soaked in automatic transmission fluid.
6. Check the fit of the C1 clutch hub on the overdrive shaft. If it is loose, the hub and shaft assembly must be replaced. Figure 8.31 - Typical C1 Clutch Assembly
Clearance

Model
Type Gear Ratio Oil Weight (Dry)SECTION 5B
MANUAL TRANSMISSION
TABLE OF CONTENTS
Specifications . . . . . . . . . . . . . . . . . . . . . . . . 5B-1 General Specifications . . . . . . . . . . . . . . . . . . 5B-1
Fastener Tightening Specifications . . . . . . . . . 5B-2
External View . . . . . . . . . . . . . . . . . . . . . . . . 5B-3 Gear T rain . . . . . . . . . . . . . . . . . . . . . . . . . . 5B-3
Power Flow . . . . . . . . . . . . . . . . . . . . . . . . . 5B-4
Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . 5B-5 Will not Shift (Control Lever Moves) . . . . . . . . 5B-5 Hard Shift or Control Lever Will not Move Into
Gear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5B-5
Gears Crash When Shifting . . . . . . . . . . . . . . 5B-5
Transmission Jumps Out . . . . . . . . . . . . . . . . . 5B-6
Transmission Locked in One Gear . . . . . . . . . 5B-6
Transmission Noise . . . . . . . . . . . . . . . . . . . . . 5B-6
Transmission Leakage . . . . . . . . . . . . . . . . . . 5B-7Diagnosis Table . . . . . . . . . . . . . . . . . . . . . . .
5B-8
Component Locator . . . . . . . . . . . . . . . . . . . 5B-9
Maintenance and Repair . . . . . . . . . . . . . . 5B-11
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . 5B-11 Shift Control Cable . . . . . . . . . . . . . . . . . . . . 5B-11
Transmission . . . . . . . . . . . . . . . . . . . . . . . . 5B-14
Unit Repair . . . . . . . . . . . . . . . . . . . . . . . . . 5B-17 Major Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . 5B-17
Main Shaft . . . . . . . . . . . . . . . . . . . . . . . . . . 5B-27
Input Shaft . . . . . . . . . . . . . . . . . . . . . . . . . . 5B-32
Counter Shaft . . . . . . . . . . . . . . . . . . . . . . . . 5B-34
Extension Housing . . . . . . . . . . . . . . . . . . . . 5B-35
Shift Cover . . . . . . . . . . . . . . . . . . . . . . . . . . 5B-36
Inspection of Components . . . . . . . . . . . . . . 5B-40
Pre-Installation Checks . . . . . . . . . . . . . . . . . 5B-45
SPECIFICATIONS
GENERAL SPECIFICATIONS
Application Description
T5WC
Floor Change
3.97 : 1 2.34 : 11.46 : 11.00 : 10.85 :1
3.71 : 1
ATF DEXRON II / III 3.4 L
Check : Every 15,000km, Replace : Every 50,000km
33kg
1st
2nd 3rd
4th 5th
Reverse
Specification
Capacity(litre)
Change Interval
Notice Add LUBRIZOL (280cc) in oil after overhauling.

Model
TypeGear Ratio Oil Manufacturer WeightPart-Time 4408 (E)
E.S.O.F. Type
1 : 1
2.48 : 1
ATF S-3, S-4 or DEXRON II, III
1.2 L
Check : Every 15,000 km
Replace : Every 50,000 km Borg Warner30 kg
SECTION 5D1
TRANSFER CASE (PART TIME 4408)
TABLE OF CONTENTS
SPECIFICATIONS
GENERAL SPECIFICATIONS
Caution: Disconnect the negative battery cable before removing or installing any electrical unit or when a tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting thiscable will help prevent personal injury and damage to the vehicle. The ignition must also be in LOCKunless otherwise noted.
Specifications . . . . . . . . . . . . . . . . . . . . . . . 5D1-1
General Specifications . . . . . . . . . . . . . . . . . 5D1-1
Schematic and Routing Diagram . . . . . . . . 5D1-2 Part Time Transfer Case - 4408 . . . . . . . . . . 5D1-2
Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . 5D1-3
Self-Diagnosis . . . . . . . . . . . . . . . . . . . . . . 5D1-4 System Description . . . . . . . . . . . . . . . . . . . . 5D1-4
Self-Diagnosis Test . . . . . . . . . . . . . . . . . . . . 5D1-8Diagnostic Diagram . . . . . . . . . . . . . . . . . . .
5D1-9
Maintenance and Repair . . . . . . . . . . . . . 5D1-10
On-Vehicle Service . . . . . . . . . . . . . . . . . . . 5D1-10
Maintenance of Transfer Case Lubricant . . 5D1-10
Transfer Case . . . . . . . . . . . . . . . . . . . . . . . 5D1-11
Unit Repair . . . . . . . . . . . . . . . . . . . . . . . . 5D1-14
Transfer Case . . . . . . . . . . . . . . . . . . . . . . . 5D1-14
Transfer Case Control Unit (TCCU) . . . . . . 5D1-36
High LowSpecification Capacity Lubrication
Application
Description