engine oil SSANGYONG MUSSO 2003 Service Manual

M162 ENGINE ELECTRICAL 1E1-9
IGNITION CABLE Preceding Work : Removal of intake air duct
1 Control Cable Connection
2 Ignition Cable
3 Spark Plug Connector
4 Coupling Plug5a, 5b Secondary Voltage Connection
E Iron Core
L1 Secondary Ignition Coil
L2 Primary Ignition Coil

1E1-10 M162 ENGINE ELECTRICAL Functions
1. Firing order : 1-5-3-6-2-4
2. The ignition cables are located on the cylinder head cover.Each ignition coil provides the high voltage to two spark
plugs simultaneously.
- T1/1 : cylinder 2 and 5
- T1/2 : cylinder 3 and 4
- T1/3 : cylinder 1 and 6
Removal & Installation Procedure
1. Disconnect the negative battery cable (1).
2. Remove the ignition cable connector from the ignition cable.
3. Disconnect the secondary spark plug connectors from the each spark plugs and remove the ignition cable. Installation Notice
3. The secondary output voltage (5a) is supplied to the No.2
cylinder spark plug through the spark plug connector. The secondary output voltage (5b) is supplied to the No.5 cylinderspark plug through the ignition cable. The guide pin (W)acts as a ground while the ignition cable is operated.
Make sure that the ignition cables are correctly routed.
Exactly install the ignition cable guide pin into the vehicle
to be grounded.
4. Installation should follow the removal procedure in the reverse order.
Tightening Torque 9 - 11 Nm

M162 ENGINE ELECTRICAL 1E1-11
Circuit Diagram
Inspection & Maintenance Procedure (for MSE)
1. While the ignition switch is in 'OFF' position, remove thewiring connectors (1 and 15) from ignition coil and measure the primary resistance between terminal No.1 and No.15.
2. During engine cranking, measure primary voltage (T1/1) between ECU terminal No. 71 and No. 69.
Notice If out of specified value, replace the ignition coil.
Specified Value
0.9 - 1.6 (20 °C)
Specified Value 200 - 350 V
Notice
Measure remaining cables.
- T1/2 : No. 72 and 69.
- T1/3 : No. 70 and 69.
If out of specified value, check ignition cable and ECU.
3. Using a multi-tester, measure the secondary coil resistance between 5a and 5b.
Specified Value 6 - 8.5 k

M161 ENGINE ELECTRICAL 1E2-7
SPARK PLUG Preceding Work : Removal of intake air duct
Tools Required
119 589 01 09 00 Spark Plug Wrence1 Screw (3 pieces)
.................................. 9 - 11 Nm
2 Adaptor (3 pieces)
3 Ignition Coil Cable Cover
4 Spark Plug Connector
5 Ignition Coil Connector 6 Bolts (M6 X 25, 4 pieces)
..................... 9 - 11 Nm
7 Ignition Coil (T1/1)
8 Coupling Plug
9 Spark Plug ......................................... 25 - 30 Nm
10 Ignition Coil (T1/2)

1E2-8 M161 ENGINE ELECTRICAL
Tightening Torque 9 - 11Nm
Replacement Procedure
1. Unscrew the three screws(1) and remove the ignition coil
cable cover Installation Notice
Tightening Torque
Clearance 25 - 30 Nm
0.8 + 0.1 mm
2. Disconnect the cable from ignition coil and spark plug.
4. Using the special tool, remove the spark plug . Installation Notice
Spark Plug Wrench 119 589 01 09 00
Notice
Tighten the spark plug with specified torque.
Install the ignition coil to number 2 and 4 cylinder, and
connect the cable to number 1, 4 and 2, 3 cylinder
- T1/1 : cylinder 1 and 4
- T1/2 : cylinder 2 and 3
3. Unscrew two bolts(M6 X 25) from each ignition coil and remove the ignition coil(arrow) . Installation Notice
Tightening Torque 9 - 11Nm

M161 ENGINE ELECTRICAL 1E2-9
IGNITION CABLE Preceding Work : Removal of intake air duct
1 Control Cable Connection
2 Ignition Cable
3 Spark Plug Connector
4 Coupling Plug5a, 5b Secondary Voltage Connection
E Iron Core
L1 Secondary Ignition Coil
L2 Primary Ignition Coil

M161 ENGINE ELECTRICAL 1E2-11
Inspection & Maintenance (for E2.3 MSE)
1. Measure the primary resistance between the cable terminals1 and 15 after removing the ignition cable wiring connector
(1 and 15) with ignition switch OFF. Notice Replace the ignition coil if out of the specified resistance.
T1/2 : between No.71 and No.69
Notice Check the ignition cable and the ECU if out of the
specified value.
3. Measure the secondary cable resistance between the ignition coil 5a and 5b using a multimeter.
2. Measure the primary voltage(T1/1) between the ECU
terminals No.72 and No.69 during the engine cranking (starter motor activated).
Specified Value 6 - 8.5 K
Specified Value0.9 - 1.6
Specified Value 200 - 350 V

OM600 ENGINE ELECTRICAL 1E3-3
1. Preheating time - control relay.Control relay functions as followings :
Switching of preheating current.
Indication of preheating finish.
Control of preheating sequence.
Indication of fault.
2. Coolant temperature sensor. Coolant temperature sensor senses coolant ’s temperature
and signals it to the preheating relay continuously.
3. Glow plug The glow plug parts are housing with M12 ´ 1.25 thread
and heating pin in housing. It is connected in a parallel circuit
with the specified voltage of 11.5V. The heating element has a heating coil and a control coil and they are connected in series.
1. Control Coil 2. Heater Coil
4. Current and temperature of glow plug Current of glow plug While the preheating system operates, current of about
30A flows in each glow plug and temperature of heating coil rises very fast.
Due to the rise of temperature, the resistance of control
coil increases therefore the current is controlled to
about 8~15A and that protects the glow plug from over-
heating.
Temperature of glow plug The temperature of the glow plug reaches up to 900 °C
after about 9 seconds and up to 1,050 °C after 30
seconds.

M162 ENGINE CONTROLS 1F1-7
41 44455657 58 59606264 65 66677172 73 74757677 78 79808182 83 86 8789
0001 02 0304 05 08091011 17 1819 20 21 2324 25 26272930 31 34 3540
Failure
code Description
Coolant temperature sensor open Coolant temperature sensor shortCoolant temperature sensor signal failureIntake temperature sensor openIntake temperature sensor short Intake temperature sensor signal failure Low battery voltageHFM sensor signal failureHFM sensor signal failure(Low)HFM sensor signal failure(High) Crankshaft position sensor signal failure (no engine revolution signal)Crankshaft position sensor signal failure(rpm > max. value)No.1 cylinder recognition failure Crankshaft position sensor signal failure (gab recognition failure)
Transmission coding failureCAN communication failure : ASR-
Transponder signal failure CAN communication failure : TCU(A/T only)CAN communication failure : TOD(E32 only)-- CAN communication failure : communication initialization failureFuel pump relay short(PWR)Fuel pump relay open/short(GND)Purge valve short
Fa
ilure
code Description
Purge valve open/short Condenser fan(HI) relay short(PWR)Condenser fan(HI) relay short(GND)No.1 knock sensor signal failureNo.2 knock sensor signal failure No.1 cylinder synchronization failure --Cluster S/W defectaveNo ignition voltage output(No.1 ignition coil) No ignition voltage output(No.2 ignition coil) No ignition voltage output(No.3 ignition coil)Crankshaft position sensor adaptation failureStart signal recognition failureNo.1 injector short(PWR) No.1 injector open/short(GND) No.2 injector short(PWR)No.2 injector open/short(GND)No.3 injector short(PWR)No.3 injector open/short(GND) No.4 injector short(PWR) No.4 injector open/short(GND)High oxygen sensor voltageLow oxygen sensor amplifying voltageOxygen sensor operating failure Not excessive lean indication in oxygen sensor(during coasting)Oxygen sensor heater short(PWR)Oxygen sensor heater open/short(GND)Low oxygen sensor voltage
SELF DIAGNOSIS FAILURE CODE

M162 ENGINE CONTROLS 1F1-21
Failurecode ItemChecking method
 Ignition:ON
Test stepRequirementSpecified
value Possible cause
10 12 11 - 14V



ECU:power
supply - terminal 30(TM.30)
2.2 


Power
supply:
- terminal 87(TM.87) 
Ignition:ON 
Power supply cable
 OVPR
IGNITION SYSTEM TEST
08, 
1.1
 1.2
1.1 
Ignition:ON
10 2 11 - 14V



Ground
cable:- Battery ground
 Ground cable
 Ground condition
(figure 1)
Diagnosis
socket
69 2
Diagnosis socket
1.2 
Ignition:ON
11 2 11 - 14V



Power
supply: - terminal 30(TM.30)
 Power supply cable
 Fuse No.8
Diagnosis socket
2.0 
Ignition:ON
51 1 11 -14V



ECU:power
supply - terminal 87(TM.87)
08, 
2.1
 2.2
2.1 
Ignition:ON 11 - 14V



Ground
cable - Electronic ground 
Ground cable
52
Diagnosis socket
11 1
Diagnosis
socket
 Ignition:OFF
11 - 14V
< 1V
3.0 
Ignition:ON
69 71 11 - 14 V



Ignition
coil(T1/1) - No.2,5 Cylinder64, 
Cable
 Ignition coil(T1/1)
 Fuse No.17
 Engine:in cranking > 10 V