torque SSANGYONG MUSSO 2003 Service Manual

8B-18 SUPPLEMENTAL RESTRAINT SYSTEM(SRS)
MAINTENANCE AND REPAIR ON-VEHICLE SERVICE AIR BAG MODULE Removal & Installation Procedure
1. Remove the steering wheel rid (LH,RH) with a screwdriver.Installation Notice Each position mark (LH,RH) is stamped on the inner surface of the rids.
Tightening Torque 7 - 11 Nm
3. Disconnect the connectors and remove the air bag module.
4. Installation should follow the removal procedure in thereverse order.
2. Unscrew the bolts from both sides.
Installation Notice

9L-8 GLASS AND MIRRORS
Tightening Torque 7.7 Nm
4. Before installation, ensure that the stay bolt washer is
inserted.
5. Using suction holders, install the side glass within 5minutes after application of sealant.

FRAME AND UNDERBODY 9N-5
1 Mounting Bolt....................................... 28-47 Nm
SKID PLATE .2 Skid Plate
Removal & Installation Procedure
1. Remove 6 mounting bolts and carefully remove the skid
plate. Installation Notice
2. Installation should follow the removal procedure in the reverse order.
Tightening Torque 28 - 47 Nm

9R-6 BODY FRONT END
5. Remove the fender mounting bolts.Notice Be careful not to damage the paintwork.
Installation Procedure
1. Installation should follow the removal procedure in the reverse order. Notice Apply a tape sealer to the fender and body panel to prevent rust in fender mounting bolts area.
Tightening Torque 7 - 9 Nm

8. ECM(E32, HFM) .......................................................................................................................... 5-64
1) INJECTOR, OVPR, IGNITION COIL, FUEL PUMP CIRCUIT(W/ IMMOBILIZER) ........................................... 5-64
2) INJECTOR, OVPR, IGNITION COIL, FUEL PUMP CIRCUIT(W/O IMMOBILIZER) ........................................ 5-66
3) SENSOR (CKP, CMP, KNOCK, MAF), CCP SOLENOID, CAM SHAFT ACTUATOR CIRCUIT ....................... 5-68
4) THROTTLE MOTOR & SENSOR, SENSOR (IAT, ECT, HEATED O 2), VSS, CIRCUIT (UNLEAD) ................. 5-70
5) THROTTLE MOTOR & SENSOR, SENSOR (IAT, ECT), CO POTENTIO METER, VSS CIRCUIT(LEAD) ..... 5-72
9. DLC CIRCUIT ................................................................................................................. ............. 5-74
10. TCM(GSL, BTRE) .............................................................................................................. ......... 5-76
1) POWER SUPPLY, GROUND, INDICATION LAMP CIRCUIT ............................................................................. 5- 76
2) KICK DOWN SWITCH, SELECT LEVER POSITION SENSOR, TRANSMISSION CIRCUIT ........................ 5-78
11. TCM(DSL, BTRE) .............................................................................................................. ......... 5-80
1) POWER SUPPLY, GROUND, INDICATION LAMP, SENSOR (TR, ENGINE SPEED) CIRCUIT .................... 5-80
2) KICK DOWN SWITCH, SELECT LEVER POSITION SENSOR, TRANSMISSION CIRCUIT ........................ 5-82
12. KICK DOWN RELAY, 'B' SWITCH CIRCUIT (MB A/T) ........................................................... 5-84
13. TCCU-PART TIME .............................................................................................................. ........ 5-86
1) POWER SUPPLY, GROUND, INDICATION LAMP, PNP RELAY, CLUTCH SWITCH CIRCUIT ..................... 5-86
2) 4WD SWITCH, T/C SPEED SENSOR, T/C MOTOR CIRCUIT ........................................................................ 5-88
14. TCCU-FULL TIME .............................................................................................................. ........ 5-90
1) POWER SUPPLY, GROUND, INDICATION LAMP, NEUTRAL RELAY, CLUTCH CIRCUIT ............................ 5-90
2) 4WD SWITCH, T/C SPEED SENSOR, T/C MOTOR CIRCUIT ........................................................................ 5-92
15. TOD(TORQUE ON DEMAND)-E32,MSE .................................................................................. 5-94 1) POWER SUPPLY, GROUND, WARNING LAMP, 4WD SWITCH, T/C MOTOR CIRCUIT .............................. 5-94
2) T/C SPEED SENSOR, PNP RELAY, CLUTCH SWITCH, CAN CIRCUIT .......................................................... 5-96
16. ECS ......................................................................................................................... ..................... 5-98
1) POWER SUPPLY, GROUND, SENSOR(WHEEL'G, VERTICAL, LATERAL) CIRCUIT ................................... 5-98
2) ECS SWITCH, DAMPER CIRCUIT ...................................................................................................................... 5-100

5-94 ELECTRICAL WIRING DIAGRAMS
15. TOD (TORQUE ON DEMAND) - E32, MSE
1) POWER SUPPLY, GROUND, WARNING LAMP, 4WD SWITCH, T/C MOTOR CIRCUIT Main - Engine Main - Engine Main Main Main
C101 (21Pin, Colorless)C103 (2Pin, White)S203 (Gray) G203 G205
b. CONNECTOR IDENTIFICATION SYMBOL & PIN NUMBER POSITION
a. CONNECTOR INFORMATION
TOD
CONNECTOR(NUMBER) CONNECTING. WIRING HARNESSCONNECTOR POSITION
Inside The Engine Room Fuse Block Inside The Engine Room Fuse Block Under Right The Audio Upper The ECMBeside The TCCU
A1 A9 A8
A18
B1
B6 B5
B12
11 2
29 38
28
13 2021
39 434842
CLUSTER
C101
W/H MAIN
12345 678910
11 12 13 14 15 16 17 18 19 20 21
C103
W/H MAIN
45
12
67
3
T/C MOTOR
1
5678910 23
4
4WD SWITCH
1
7 7 S203
GND
BAT+
30
IGN1
ILL
15 58
31
Ef9 60A
F20 10A
F10 20A
B4 B5
G205 G203
TOD
YW LW
LgW LgW
B11 YW
2
C103
WYW
IGN1
F22
10AEf1010A
A9 LB 18
35 31
4L
4WD
CHECK
B+
B+
GND
SIG
A16 B9
BB
GNDB10
B
A1
5V
5V
5V
5V
5V SIG
A4
B7B2
6
B 7
G 4
A 2
E 1
D 3
C 5
F
RW RWB6
R
B1
R
LgWSIG
A5RW SIG
A15Br
T/C MOTOR SIG
A18
Ef2 80A
"A15"
TCMGrR BW BW GW GW
GW
B
59 1
0
A24L 4H
4
C101
4WD Switch
Cluster
M
1
2