turn signal SSANGYONG NEW ACTYON SPORTS 2013 User Guide

01-12
(3) Turn signal lamp (Hazard warning lamp operation)
The B+ power supplied through the No. F66 interior fuse on the right-hand of the engine compartment is
on standby on the No. 30 and 86 hazard warning lamp relay terminals via the ICM No. 18 terminal.
The STICS activates and/or controls the hazard warning lamp relay using the No. A26 terminal
depending on the operating conditions. The activated relay supplies the No. 87 and 87a terminals with
the power, which is on standby on the No. 30 hazard warning lamp relay terminal.
The supplied power flows to the corresponding circuit via the No. 7 and 16 ICM terminals.

02-58710-01
NO.Input Signal Name Logic Status
27 Central door lock switch ON = GND, OFF = OPEN
28 Multifunction auto light switch ON = GND, OFF = OPEN
29 Turn signal lamp switch ON = BAT/GND, OFF = OPEN
(approx. 5.1 V ~ 9.2 V)
30 Rain sensor ON = GND (DATA), OFF = BAT
31 Telematics ON = GND (DATA), OFF = BAT
32 Diagnosis ON = GND (DATA), OFF = BAT (KWP2000)

02-10
▶Auto Washer and Wiper Switch (AFW)When the auto washer switch is turned on with the ignition switch "ON" and the INT switch
"OFF", the washer motor output gets ON for 1 second. If the system recog\
nizes the output signal,
the wiper relay output gets ON during 4 cycles and the washer motor output gets ON for 1
second. Then, the wiper relay output gets OFF after 3 cycles.
-

02-138710-01
Rain sensing unit
(AUTO light integrated type)
▶INT Switch Auto Position Remi nder (Power-Up Reminder Wiper)
When turning off and on the auto INT switch, the system drives the wiper motor through LOW
relay regardless of communication with rain sensor.
When turning the INT-AUTO switch from the "OFF" to "ON" position with the ignition switch in the
"ON" mode, the LOW relay operates to drive the wiper motor for 1 cycle, regar\
dless of the rain
sensor communication.
After that, when turning the INT-AUTO switch fr om the "OFF" to "ON" position, the LOW relay
operates to drive the wiper motor for 1 cycle only if data from the rain\
sensor indicates rain drops.
-
-
Multifunction wiper switch:
AUTO and sensitivity control
A sensor that emits infrared rays through LED and
then detects the amount of rain drops by receiving
reflected rays against sensing section (rain senso
r
mounting section on the windshield) with
photodiode (auto light sensor integrated type) AUTO
: Wiper operates automatically by rain sensor
FAST↔SLOW : Auto delay/Auto speed control. A
position that can control sensitivity against rains on
the windshield and transmits wiping demand signal
accordingly

02-158710-01
▶Sensitivity ControlThe wiper LOW relay is turned on and the wiper motor runs one cycle when the volume sensitivity
is increased (ex: sensitivity 0 ⇒ 1) while the ignition switch and the INT switch is in the "ON"
position, and the wiper motor is in "Parked" position). However, the wiper motor can be operated
only when the rain sensor detects the "Rain Detected" signal.
If the volume sensitivity is changed more than 2 stages within 2 seconds, the wiper motor runs
only one cycle.
-
※

02-26
▶Tail Lamp Left On WarningThe chime buzzer sounds with the interval of 0.8 second when opening the\
driver's door while the
tail lamp is turned on and the ignition key is removed.
The c/buzzer output stops when turning off the tail lamp and closing the\
driver's door.
The system outputs "UNLOCK" signal for 5 seconds when the driver's and p\
assenger's door lock
switch is locked (while the tail lamp is turned on and the driver's doo\
r is open).
This function does not work when the IGN1 switch is in "ON" position.
-
-
-
-

02-30
▶Center Room Lamp Control
The overhead console lamp (front room lamp) and the center room lamp come on at 100% when
opening the door (driver's/passenger's/rear) while the center room lamp switch\
is at the doo
r
coupled/tailgate coupled operating position and the key reminder switch \
is "OFF".
When the door (driver's/passenger's/rear) is opened, the front and center room lamps come on at
100% and automatically go off after 30 seconds.
The room lamp stays on for 2 seconds and then dims through 3 seconds whe\
n closing the doors
within 30 seconds.
The dimming operation must have greater than 32 steps per one second.
The room lamp output should stop immediately after turning on the ignition key during the
dimming operation.
The front room lamp and the center room lamp come on for 30 seconds when\
receiving the
unlock signal from the remote control key while the doors are closed.
The front room lamp and the center room lamp output period is extended b\
y 30 seconds when
receiving the unlock signal from the remote control key again during output under step (5). (The
lamp stays on when unlocked by the remote control key.)
When a door is opened during its extended period, the lamp stays on. If closed, operates as in
step (2).
The room lamp output stops immediately after receiving the lock signal from door lock switches
while all doors are closed or entering into the anti-theft mode by pushi\
ng LOCK button on the
remote control key.
1.
2.
3.
4.
5.
6.
7.
8.

02-32
▶Ignition Key Hole IlluminationThe ignition key hole illumination comes on when opening the driver's door or passenger's doo
r
while the ignition key is removed.
The ignition key hole illumination stays on for 10 seconds when closing \
the door after step (1).
The output stops when the ignition key is turned to the "ON" position.
The output stops when receiving the lock signal from the remote control key and entering armed
mode.
1.
2.
3.
4.
▶Key cylinder with key hole illumination With diesel and gasoline engine With diesel engine With gasoline engine
Without immobilizer
→With key hole
illumination With immobilizer
→With key hole
illumination With immobilizer
→Without key hole
illumination function

02-418710-01
The door lock system outputs "LOCK" when the vehicle speed maintains over 30 km/h.
However, it doesn't output "LOCK" when all doors are locked or failed.
If any of doors is unlocked after outputting "LOCK" in step 1, outputs "LOCK" up to 5 times
(except step (1)) at the interval of one second.
If any of doors is unlocked after 5 times of "LOCK" outputs, the door (driver's/passenger's/rear) is
regarded as "FAIL".
If the door that was regarded as fail is changed (UNLOCK to LOCK), it will be recognized as a
normal one.
If any door is regarded as FAIL, the auto door lock function does not work. (if it is occurred when
the vehicle speed is over 30 km/h, the auto door lock output does not occur even if the vehicle
speed falls below 30 km/h and accelerates again to over 30 km/h.) Nonetheless, the central
door lock function works properly.
When the system receives "UNLOCK" signal fr om a door switch, it outputs "LOCK" signals 5
times. If additional "LOCK" signal from another door switch is detected during \
the period, the
system outputs five "LOCK" signals 5 times for the switch.
The door lock system outputs "UNLOCK" automatically if the "LOCK" output conditions are
established by this function or the key is cycled (IGN=OFF) (even when there is no "LOCK"
output while the vehicle speed maintains over 30 km/h under lock conditi\
on).
(If the LOCK condition is established with the ignition switch ON, the system outputs UNLOCK
signal unconditionally when turning the ignition switch to OFF position.\
)
However, when the ignition key is turned to "OFF" position, the lock output conditions will be
cancelled.
The "FAIL" condition of the door will be erased when the ignition key is\
turned to "OFF" position.
1.
2.
3.
4.
5.
6.
7.
8.
▶Auto Door Lock
T2: 0.5 s
(*1) LOCK: Driver's & Passenger's & Rear door & = Lock

02-42
▶Auto Door Unlock (Crash Unlock: Automatic Door Unlock in Collision)
The air bag collision signal input cannot be accepted within 7 seconds after turning the ignition
key to "ON" position.
After this period, the door lock system outputs "UNLOCK" for all doors for 5 seconds from 40 ms
after receiving the air bag collision signal.
Even though the key is turned to "OFF" position during the output of "UNLOCK", the output
continues on for remaining period.
The function is erased when turning "OFF" the ignition switch.
1.
2.
3.
4.
Cautions for door lock/unlock control
The "Unlock" control by air bag signal prevails over any "LOCK" or "UNLOCK" control by othe
r
functions.
The "LOCK/UNLOCK" request by other functions will be ignored after/durin\
g the output o
f
"UNLOCK" by the air bag.
However, the door lock is controlled by other functions when the ignitio\
n switch is "OFF".
"LOCK" (or "UNLOCK") output is ignored if "LOCK" (or "UNLOCK") output is required while
performing the output of "LOCK" (or "UNLOCK").
(However, UNLOCK by air bag signal and operation by the remote control \
key are valid.)
If the door lock system outputs "LOCK" and "UNLOCK" simultaneously, only\
the "LOCK" output
can be activated.
1.
2.
3.
4.