key SSANGYONG RODIUS 2012 User Guide
Page 436 of 715
02-58710-01
The remote engine control function has been deleted in this model.
1. COMPONENTS
STICS / ICM module
Air bag ECU
Sends the vehicle collision
signals to STICS.
Theft deterrent horn
Installed under the battery.
This horn works only for the
theft deterrent function,
panic function, and remote
starting.
SCAN-tool
SIW is used for REKES key
coding and trouble
diagnosis.
REKES
Added the escort and
panic function
RK STICS
ICM module
This module contains
various relays, chime and
buzzer controlled by STICS
Page 437 of 715
02-6
2. FUNCTIONS OF RK STICS
1) Wiper Control
(1) Wiper MIST and Washer Coupled Wiper
The wiper relay is turned on 0.3 seconds (T1) after turning “ON” the washer switch for 0.2 ~
0.59 seconds (T2) with the ignition key “ON”, and it is turned off when the parking terminal is
turned off. 1.
The wiper relay is turned on 0.3 seconds (T1) after turning “ON” the washer switch over 0.6
seconds (T2) with the ignition key “ON”, and it is turned on three times immediately after
turning off the washer switch. 2.
Page 440 of 715
02-98710-01
▶ Rain sensing operation point
The wiper relay is turned on and the wiper motor runs one cycle when the ignition key is
<009b009c00990095008c008b0047009b0096004702c80076007502c9004700970096009a0090009b0090009600950047004f009e008f00900093008c0047009b008f008c0047009e00900097008c00990047009a009e0090009b008a008f00470090009a00
4700900095004702c80068007c007b007602c9004700970096>sition).
The wiper relay (LO) is turned on and the wiper motor runs one cycle when changing the
<009e00900097008c00990047009a009e0090009b008a008f0047009b0096004702c80068007c007b007602c9004700970096009a0090009b0090009600950047008d00990096009400470088009500a000470096009b008f008c0099004700970096009a00
90009b009000960095009a0047004f009e008f00900093008c> the ignition key is in “ON”
<00970096009a0090009b009000960095005000550047007e008f008c00950047009b008f008c0047009e00900097008c00990047009a009e0090009b008a008f00470090009a0047009b009c00990095008c008b0047009b0096004702c80068007c007b00
7602c9004700970096009a0090009b00900096009500470088>gain from other positions, the
system drives the wiper relay (LO) to run the wiper motor one cycle only when the rain sensor
detects the “Rain Detected” signal. 1)
2)
Page 442 of 715
02-118710-01
The wiper system continuously outputs the parking signal of current sensitivity when the
parking terminal is grounded (while the ignition key is in “ON” position and the wiper switch is
in “AUTO” position). 1)
<0b540047007b008f008c0047009e00900097008c0099004700940096009b0096009900470099009c0095009a004700960095009300a00047009e008f008c00950047009b008f008c004700990088009000950047009a008c0095009a009600990047009900
8c0098009c00900099008c009a0055>
When the parking terminal is fixed to IGN (HIGH), the wiper system outputs the operating
signal of current sensitivity for 2 seconds, then continuously outputs the parking signal of
current sensitivity. 2)
<0b540047007b008f008c0047009e00900097008c0099004700940096009b0096009900470099009c0095009a004700960095009300a00047009e008f008c00950047009b008f008c004700990088009000950047009a008c0095009a009600990047009900
8c0098009c00900099008c009a0055>
▶ Wiper operation when the wiper parking terminal is grounded
Page 444 of 715
02-138710-01
The wiper relay (LO) is turned on and the wiper motor runs one cycle when the wiper
sensitivity is changed to 3 from 4 during receiving the malfunction signal (2) from the rain
sensor (while the ignition key is in “ON” position and the wiper switch is in “AUTO” position). 2)
The wiper relay (LO) is turned on and the wiper motor runs one cycle when the wiper sensitivity
is changed to 2 from 1 during receiving the malfunction signal (3) from the rain sensor (while
<009b008f008c00470090008e00950090009b00900096009500470092008c00a000470090009a004700900095004702c80076007502c9004700970096009a0090009b009000960095004700880095008b0047009b008f008c0047009e00900097008c009900
47009a009e0090009b008a008f00470090009a004700900095> “AUTO” position). Also, the wiper
relay (LO) is turned on and the wiper motor runs one cycle when the wiper sensitivity is
changed to 2 from 1 during receiving the ground fixed or IGN fixed signal from the rain sensor. 3)
Page 448 of 715
02-178710-01
2) Ignition Key Reminder
▶Key Reminder Warning
<007b008f008c0047008a008f00900094008c00470089009c00a100a1008c009900470096009c009b0097009c009b0047009000950047009b008f008c00470070006a0074004700890096009f0047008a00960095009b00900095009c008c009a0047009e00
8f008c0095004700960097008c009500900095008e0047009b>he driver’s door while the
ignition key is inserted into ignition switch.
<007e008f008c009500470099008c00940096009d00900095008e0047009b008f008c00470090008e00950090009b00900096009500470092008c00a00047009600990047008a00930096009a00900095008e0047009b008f008c0047008b00990090009d00
8c009902c5009a0047008b0096009600990047008b009c0099>ing chime buzzer output, the
output turns off.
This function is not available when the ignition switch is “ON”. 1.
2.
3.
Page 449 of 715
02-18
This function does not work if the vehicle speed is over 3 km/h.
<007b008f008c0047009a00a0009a009b008c009400470096009c009b0097009c009b009a004702c8007c007500730076006a007202c90047008d009600990047005c0047009a008c008a00960095008b009a0047004f007b005900500047008d0099009600
94004700570055005c0047009a008c008a00960095008b009a> after the driver’s door is
<00960097008c0095008c008b004700880095008b0047009b008f008c0047008b009600960099004700930096008a00920047009a009e0090009b008a008f00470090009a0047008a008f00880095008e008c008b0047009b0096004702c800730076006a00
7202c90047004f009e008f00900093008c0047009b008f008c> ignition key is in ignition
switch).
<007b008f008c0047009a00a0009a009b008c009400470096009c009b0097009c009b009a004702c8007c007500730076006a007202c90047008d009600990047005c0047009a008c008a00960095008b009a0047004f007b005900500047009e008f008c00
950047009b008f008c0047008b009600960099004700930096>ck switch is changed to
“LOCK” from “UNLOCK” and the driver’s door is closed within 0.5 seconds (T1) (while the
ignition key is in ignition switch). 1.
2.
3. ▶Key Reminder
Operating conditions for (*1) and (*2) -
<004f00510058005000610047006b00990090009d008c009902c5009a0047008b00960096009900470090009a004700960097008c0095008c008b004700880095008b0047008b00990090009d008c009902c5009a0047008b00960096009900470093009600
8a00920047009a009e0090009b008a008f00470090009a0047>turned to LOCK
<004f0051005900500061004700770088009a009a008c0095008e008c009902c5009a0047008b00960096009900470090009a004700960097008c0095008c008b004700880095008b004700970088009a009a008c0095008e008c009902c5009a0047008b00
9600960099004700930096008a00920047009a009e0090009b>ch is turned to LOCK
Page 450 of 715
02-198710-01
▶All Door Lock Prevention Function when a Door is Opened
When a door is opened, all doors should be unlocked for 5 seconds if inputs LOCK signal. 1.
The LOCK signal means the central door locking (REKES, central door lock switch, knob
switch) except LOCK input by rear door knob.
After unlocking and o
p<008c009500900095008e004700960095009300a00047009b008f008c0047008b00990090009d008c009902c5009a0047008b0096009600990047009e0090009b008f00470099008c00940096009b008c0047008a00960095009b0099009600930047009200
8c00a00047009c0095008b008c00990047008800990094008c>d mode
<004f008b00990090009d008c009902c5009a0047008b00960096009900470090009a0047009c009500930096008a0092008c008b00470089009c009b004700970088009a009a008c0095008e008c009902c5009a004700880095008b00470099008c008800
990047008b009600960099009a004700880099008c00470093>ocked), only the driver’s door
generates unlock signal when trying to lock the driver’s door with the driver’s door opened.
Above operations is regardless of key positions and have priority over the ignition key
reminder function. -
-
-
When the door is closed during unlock output for 5 seconds under item 1 condition, the unlock
output stops. 2.
<0068009300930047008b009600960099009a0047008c009f008a008c0097009b0047009b008800900093008e0088009b008c004700880095008b0047008f00960096008b00470096009c009b0097009c009b004702c8007c007500730076006a007202c900
47008d009600990047005c0047009a008c008a00960095008b>s (T1) when the “LOCK”
signal is inputted (while the ignition key is removed and a of door is opened).
When the door is closed during unlock output for 5 seconds, the unlock output stops. -
-
Page 451 of 715
02-20
3) Mark Lamp Left on Warning
The chime buzzer in the ICM box sounds with the interval of 0.8 second when opening the
<008b00990090009d008c009902c5009a0047008b0096009600990047009e008f00900093008c0047009b008f008c0047009b0088009000930047009300880094009700470090009a0047009b009c00990095008c008b004700960095004700880095008b00
47009b008f008c00470090008e00950090009b009000960095> key is removed.
<007b008f008c00470089009c00a100a1008c009900470096009c009b0097009c009b0047009a009b00960097009a0047009e008f008c00950047009b009c0099009500900095008e00470096008d008d0047009b008f008c0047009b008800900093004700
93008800940097004700880095008b0047008a00930096009a>ing the driver’s door.
<007b008f008c0047009a00a0009a009b008c009400470096009c009b0097009c009b009a004702c8007c007500730076006a007202c90047008d009600990047005c0047009a008c008a00960095008b009a0047009e008f008c00950047009b008f008c00
47008b00990090009d008c009902c5009a004700880095008b> passenger’s door lock
switch is locked (while the tail lamp is turned on and the driver’s door is opened).
This function is not available when the ignition key is in “ON” position. 1.
2.
3.
4.
Page 455 of 715
02-24
7) Room Lamp Control
▶ Front Room Lamp
The front room lamp comes on when opening the
driver’s door or passenger’s door while the front
room lamp switch is at door coupled position and
the key reminder switch is turned off.
The room lamp stays on for 2 seconds (T1) and
then decays through 3 seconds (T2) when closing
the driver’s door or passenger’s door.
The room lamp output should stop immediately
after turning on the ignition key during decaying
operation.
The front room lamp comes on for 30 seconds
(T3) when receiving the unlock signal from the
remote control key while the door is closed. 1.
2.
3.
4.
The front room lamp output period is extended by 30 seconds (T3) when receiving the unlock
signal from the remote control key again during output.
When a door is opened during its extended period, the lamp stays on. If closed, operates as in
step 2.
<007b008f008c004700990096009600940047009300880094009700470096009c009b0097009c009b0047009a009b00960097009a0047009000940094008c008b00900088009b008c009300a000470088008d009b008c009900470099008c008a008c009000
9d00900095008e0047009b008f008c004700930096008a0092> signal from driver’s door and
<00970088009a009a008c0095008e008c009902c5009a0047008b009600960099004700930096008a00920047009a009e0090009b008a008f0047009e008f00900093008c0047009b008f008c0047008b00990090009d008c009902c5009a0047008b009600
960099004700880095008b004700970088009a009a008c0095>ger’s door are closed. 5.
6.
7.
Door coupled front
room lamp switch