display SUBARU CROSSTREK 2017 1.G Multimedia System Manual

TIPS FOR THE NAVIGATION SYSTEM
244
TIPS FOR THE NAVIGATION SYSTEM
GPS (GLOBAL POSITIONING
SYSTEM)
REGARDING ERRORS IN CURRENT
POSITION DISPLAY
The system displays the vehicle current position based on
GPS information and data from various sensors and road
maps. However, when the radiowave signals from GPS
satellites are weak or when signals are received from only
two satellites or less, errors may occur in the position.
Modifying or adjusting the system will not prevent these
errors.
LIMITATIONS OF THE NAVIGATION SYSTEM
This navigation system calculates the current position using
satellite signals, various vehicle signals, map data, etc.
However, an accurate position may not be shown depending
RQ VDWHOOLWH FRQGLWLRQV URDG FRQ

TIPS FOR THE NAVIGATION SYSTEM
245
NAVIGATION SYSTEM
8
CAUTION
OThe installation of window tinting may obstruct the GPS
signals. Most window tinting contains some metallic content
that will interfere with GPS signal reception of the antenna in
the instrument panel. We advise against the use of window
tinting on vehicles equipped with navigation systems.

”Accurate current position may not be shown in the
following cases:
‡When driving on a small angled Y-shaped road.
‡When driving on a winding road.
‡When driving on a slippery road such as in sand,
gravel, snow, etc.
‡When driving on a long straight road.
‡When freeway and surface streets run in parallel.
‡After moving by ferry or vehicle carrier.
‡When a long route is searched during high speed
driving.
‡After repeating a change of direction by going
forward and backward, or turning on a turntable in
a parking lot.
‡When leaving a covered parking lot or parking
garage.
‡When a roof carrier is installed.
‡When driving with tire chains installed.‡When the tires are worn.
‡After replacing a tire or tires.
‡When using tires that are smaller or larger than the
IDFWRU\VSHFL¿FDWLRQV
‡When the tire pressure in any of the 4 tires is not
correct.

”Inappropriate route guidance may occur in the
following cases:
‡When turning at an intersection off the designated
route guidance.
‡If you set more than 1 destination but skip any of
them, auto reroute will display a route returning to
the destination on the previous route.
‡When turning at an intersection for which there is
no route guidance.
‡When passing through an intersection for which
there is no route guidance.
‡During auto reroute, the route guidance may not be
available for the next turn to the right or left.
‡During high speed driving, it may take a long time
for auto reroute to operate. In auto reroute, a detour
route may be shown.
‡After auto reroute, the route may not be changed.
‡If an unnecessary U-turn is shown or announced.

Siri
250
”To cancel Siri, select
Cancel (Cancel), or press and
hold the talk switch.
NOTE
OSiri cannot be started while placing or receiving hands-free
calls with your iPhone and iPod touch (including while holding
incoming calls), or while having a hands-free conversation.
OSiri cannot be used while using the system’s voice recognition
function. Start Siri after exiting the voice recognition function.
OThe system screen will display the calling screen when a hands-
free call is placed.
OUnit operation while using Siri will differ depending on your
iPhone or iPod touch.
OSiri may not recognize what is being said if:
‡Spoken too quickly.
‡Spoken at a low or high volume.
‡Driving with a window open.
‡Passengers are talking while using Siri.
‡The air conditioning speed is set high.
‡When air from the ventilator blows directly toward the
microphone.
OIn the following conditions, the system may not recognize what is
being said properly, and use of Siri may not be possible.
‡What is being said is incorrect or unclear. Note that certain
ZRUGV DFFHQWV RU VSHHFK SDWWHUQV PD\ EH GLI

VOICE RECOGNITION SYSTEM OPERATION
254
NOTE
OWhile the recognition data is being created or being updated, a
track search cannot be performed using a voice command.
VOICE COMMAND EXAMPLE: CALL NAME
1. Press the talk switch.
2. Say “Call <contacts> <phone types>”.

”If multiple matching items are found, a selection
screen will be displayed. Say “<number>” or select
the number.
NOTE
OIn the same manner as it is displayed on the screen, “Call
<contacts> <phone types> (Call <contacts> <phone types>)”,
after saying “Call a contact” say the name, or the name and
type of phone, of a contact.
For example: “Call a contact”, “John Smith” or “Call a
contact”, “Mary Davis”, “Mobile”
OThere are 4 types of phones: Home, Mobile, Work and Other.
OShort or abbreviated names in the contacts list may not be
recognized. Change names in the contacts list to full names.
O6RPHWLPHVDYRLFHUHFRJQLWLRQUHVXOWFRQ

COMMAND LIST
257
Siri/VOICE RECOGNITION SYSTEM
9
COMMAND LIST
Recognizable voice commands and their actions are shown
below.

”Frequently used commands are listed in the following
tables.

”For devices that are not installed in the vehicle, the
related commands will not be displayed in the screen.
Also, according to conditions, other commands may
not be displayed in the screen.

”The functions available may vary according to the
system installed.

”Voice recognition language can be changed.

:3
NOTE
OThe notations used in the commands are as follows.
‡>
|
|
|UUU]: Commands that need not to be spoken
‡<UUU>: Numbers, titles, or names to be spoken
XBasic command
Voice command Phrase Function
System pause pausePause the current
voice interaction
System back [go] backGo back one
hierarchy
System cancel cancelCancel the current
task
System help helpAsk for help with
the current task
System start over start overStart the current
task over
Page change¿UVWSDJHODVW
page, previous
page, next pageChange display
page

COMMAND LIST
259
Siri/VOICE RECOGNITION SYSTEM
9
XCommands for Hands-free
Voice command Phrase Function
Redialredial, call again, dial
againPlaces a call to the
phone number of
the latest outgoing
call
Call backcall back, return phone
callPlaces a call to the
phone number of
latest incoming call
Recent calls [show] recent callsDisplays the call
history screen
Dial number
callingcall <phone number>,
dial <phone number>Places a call to
the said phone
number
Call by name
and typecall <contacts>
<phone types>,
dial <contacts> on
<phone types>Place a call to the
said phone type of
the contact from
the phone book
List messagelist messages, list
<messagetypes>
messagesDisplays e-mails
Call call
This can be used
when receiving
messages Ignore ignore
Read read
Reply reply
XCommands for Pandora*
*: Pandora is available in the United States, Australia, and New Zealand.
Voice command Phrase Function
Pandora mode
changeplay Pandora stationsSwitch to Pandora
mode
List Pandora
stationslist Pandora stationsList Pandora
stations
Thumb up like, thumbs up0DUN³/LNH´ÀDJ
Thumb down dislike, thumbs down0DUN³'LVOLNH´ÀDJ
and skip to the
next song
XCommands for aha
Voice command Phrase Function
aha mode
changeplay aha stationsSwitch to aha
mode
List aha stations list aha stations List aha stations
Like on/offlike/unselect like,
thumbs up/unselect
thumbs up0DUN³/LNH´ÀDJ
Unmark it

COMMAND LIST
265
Siri/VOICE RECOGNITION SYSTEM
9
Voice command Phrase Function
Go go5HÀHFWVWKH
selected route
and starts the
navigation
guidance
Go mapgo to [the] map
Transits to the
Map screen [screen] show [me]
[the] map
[screen] back to [the]
map
Help helpTransits to the
voice recognition
mode’s help
screen
Half halfReduces the
detour distance set
on the avoid route
screen by halfVoice command Phrase Function
History>¿QG@>LQ@KLVWRU\Sets the
destination from
the search history
results
Less lessReduces the
detour distance set
(on the avoid route
screen)
Line 1[line] 1 Selects the item
OLVWHGLQWKH¿UVW
line of the list
(on the screen
where the list is
displayed) ¿UVW>OLQH@
Line 2[line] 2Selects the item
listed in the
second line of the
list (on the screen
where the list is
displayed) second [line]

COMMAND LIST
266
Voice command Phrase Function
Line 3[line] 3Selects the item
listed in the third
line of the list
(on the screen
where the list is
displayed) third [line]
Line 4[line] 4Selects the item
listed in the fourth
line of the list
(on the screen
where the list is
displayed) fourth [line]
Middle[go, jump, move, scroll]
[to] [the] middleTransits to the
middle of the list
(on the screen
where the list is
displayed)
More moreTransits to the
information list
reception screenVoice command Phrase Function
Near here[near] here
Narrows down
the selected POI
search candidates
to places along the
route nearby
around here
in the neighborhood
New route new routeRegisters
the selected
destination as a
new destination
Next nextTransits to the next
screen
Nono
Rejects questions
or other contents
spoken to you nope
nop

WHAT TO DO IF
287
APPENDIX/WHAT TO DO IF/INDEX
10
XWhen using the Bluetooth message function
Symptom Likely cause SolutionPage
Cellular
phoneThis
system
Messages cannot be viewed.Message transfer is not enabled on
the cellular phone.Enable message transfer on the
cellular phone (approve message
transfer on the phone).*-
Automatic transfer function on this
system is set to off.Set automatic transfer function on
this system to on.- 145
1HZPHVVDJHQRWL¿FDWLRQVDUHQRW
displayed.1RWL¿FDWLRQRI606006(PDLO
reception on this system is set to off.6HWQRWL¿FDWLRQRI606006(PDLO
reception on this system to on.-145
Automatic message transfer function
is not enabled on the cellular phone.Enable automatic transfer function on
the cellular phone.*-
*: For details, refer to the owner’s manual that came with the cellular phone.

WHAT TO DO IF
288 XIn other situations
Symptom Likely cause SolutionPage
Cellular
phoneThis
system
The Bluetooth connection status is
displayed at the top of the screen
each time the ignition switch is turned
to the “ACC” or “ON” position.&RQQHFWLRQFRQ¿UPDWLRQGLVSOD\RQ
this system is set to on.To turn off the display, set connection
FRQ¿UPDWLRQGLVSOD\RQWKLVV\VWHP
to off.- 188
Even though all conceivable
measures have been taken, the
symptom status does not change.The cellular phone is not close
enough to this system.Bring the cellular phone closer to this
system.--
The cellular phone is the most likely
cause of the symptom.Turn the cellular phone off, remove
and reinstall the battery pack, and
then restart the cellular phone.*-
Enable the cellular phone’s Bluetooth
connection.*-
Stop the cellular phone’s security
software and close all applications.*-
Before using an application installed
on the cellular phone, carefully check
its source and how its operation
might affect this system.*-
*: For details, refer to the owner’s manual that came with the cellular phone.