Automatic trans SUBARU FORESTER 2000 SF / 1.G User Guide

Page 187 of 322

7-12n
Manual transmission vehicles:
HS0125
1
2
The key c an b e turned from “ACC ” to “LOCK ” only when the key is
p ushed in while turning it. ACC
In this p osition the elec tric al ac c essories (rad io, ac c essory p ower
soc ket, etc .) c an b e used . ON
This is the normal op erating p osition after the eng ine is started .
START
CAUTION
Do not turn the ignition switch to the “START” position while the
engine is running.
The eng ine is started in this p osition. The starter c ranks the eng ine to
start it. When the key is released (after the eng in e has started ), the
key automatic ally returns to the “ON ” p osition.
Key reminder chime
The remind er c hime sound s when the d river ’s d oor op ens and the key is
in the “LOCK ” or “ACC ” p ositions. The c hime stop s when the key is re-
moved from the ig nition switc h.

Page 189 of 322

7-14tral. Hold the c lutc h p ed al to the floor while star
ting the eng ine. The
starter motor will only op erate when the c lutc h p ed al is p ressed fully
to the floor.
4. Turn the ig nition switc h to the “ON ” p osition and c hec k the op era-
tion of the warning and ind ic ator lig hts. Refer to “Warning and ind ic a-
tor lig hts ” sec tion (Chap ter 3).
5. Turn the ig nition switc h to the “START ” p osition without d ep ressing
the ac c elerator p ed al. Release the key immed iately after the eng ine
has started .
If the eng ine d oes not start within ten sec ond s, wa it a while and then
turn the ig nition switc h to the “START ” p osition ag ain while d ep ressing
the ac c elerator p ed al half way d own.
6. Confirm that all warning and ind ic ator lig hts hav e g one off after the
eng ine has started . The fuel injec tion system autom atic ally lowers the
id le sp eed as the eng ine warms up . Automatic transmission vehicles CAUTION
If you restart the engine while the vehicle is moving, shift the se- lector lever into the “N” position. Do not attempt to place the se-
lector lever of a moving vehicle into the “P” position.
1. Ap p ly the p arking b rake.
2. Turn off unnec essary lig hts and ac c essories.
3. Shift the selec tor lever to the “P ” or “N ” p osition (p referab ly “P ”
p osition).
The starter will only op erate when the selec t lever is at the “P ” or “N ”
p osition.
4. Turn the ig nition switc h to the “ON ” p osition and c hec k the op era-
tion of the warning and ind ic ator lig hts. Refer to “Warning and ind ic a-
tor lig hts ” sec tion (Chap ter 3).
5. Turn the ig nition switc h to the “START ” p osition without depress-
ing the accelerator pedal . Release the key immed iately after the en-
g ine has started .

Page 194 of 322

Starting and operating7-19

CONTINUED –
Automatic transmission
WARNING
Do not shift from the “P” or “N” position into the “D”, “3”, “2”,
“1” or “R” position while depressing the accelerator pedal. This
may cause the vehicle to jump forward or backward.
CAUTION
Shift into the “P” or “R” position only after the vehicle is com-
pletely stopped. Shifting while the vehicle is moving may cause
damage to the transmission. Do not race the engine for more than five seconds in any posi-
tion except the “N” or “P” position when the brake is set or the
tires are on blocks. This may cause the automatic transmissionfluid to overheat. Avoid shifting from one of the forward driving positions into
the “R” position or vice versa until the vehicle has completely
stopped. Such shifting may cause damage to the transmission.
The automatic transmission is elec tronic ally c ontro lled with 4-forward
sp eed s and 1-reverse sp eed .
NOTE
Immediately after a disconnected battery is reconnected or ATF (au- tomatic transmission fluid) is replaced, you may feel that the auto-matic transmission operation is somewhat unusual.This results from erasure or invalidation of data which the on-boardcomputer has collected and stored in memory to allow the transmis-sion to shift at the most appropriate times for the current conditionof your vehicle. Optimized shifting will be restored as the vehiclecontinues to be driven for a while.

Page 196 of 322

Starting and operating7-21

CONTINUED –

R (Reverse)
This p osition is for b ac king the vehic le.
To shift from the “N ” to “R ” p osition, first stop the vehic le c omp letely
then move the lever to the “R ” p osition while p ushing the release b ut-
ton. N (Neutral)
WARNING
Do not drive the vehicle with the selector lever in the “N” (neutral)
position. Engine braking has no effect in this condition and the risk of an accident is consequently increased.
This p osition is for restarting a stalled eng ine.
In this p osition the wheels and transmission are no t loc ked . In this
p osition, the transmission is neutral; the vehic le will roll freely, even on
the slig htest inc line unless the p arking b rake or f oot b rake is on.
Avoid c oasting with the transmission neutral.
During c oasting , the eng ine b raking d oes not ac t. D (Drive)
This p osition is for normal d riving .
The transmission automatic ally shifts into a suitab le g ear from 1st to
4th ac c ord ing to the vehic le sp eed and the ac c elera tion you req uire.
When more ac c eleration is req uired in this p osition , p ress the ac c eler-
ator p ed al fully to the floor and hold that p ositio n. The transmission
will automatic ally d ownshift to 3rd , 2nd or 1st g ea r. When you release
the p ed al, the transmission will return to the orig inal g ear p osition.
n While climbing a grade
When d riving up a hill, und esired up shift to 4th g e ar is p revented from
taking p lac e when the ac c elerator is released . This minimizes the
c hanc e of sub seq uent d ownshifting to a lower g ear w hen ac c elerat-
ing ag ain. This p revents rep eated up shifting and d o wnshifting result-
ing in a smoother op eration of the vehic le.

Page 197 of 322

7-22NOTE
The transmission may downshift to 2nd or 1st gear, depending on the way the accelerator pedal is pressed to accelerate the vehicleagain. n
While going down a hill
When d esc end ing a steep hill, d ep ressing the b rake p ed al will c ause
the transmission to d ownshift to 3rd g ear, thus ap p lying eng ine b rake-
ing . Reac c eleration for a short time will c ause the transmission to up -
shift normally. NOTE In some cases, depressing the brake pedal on a downhill grade
does not result in an automatic downshift to 3rd gear. This canhappen when the automatic transmission fluid temperature is
very low, for example, during driving shortly after the vehicle has
been parked for an extended period of time. When the ATF tem-perature has risen to a certain level, automatic downshift normal-ly takes place. In the meantime, downshift manually for enginebraking as required.Also, downshifting when braking downhill will not occur at
speeds above approximately 50 mph (80 km/h). 3 (Third)
This p osition is for using eng ine b raking when g oin g d own a hill or for
c limb ing a g rad e.
The transmission automatic ally shifts into a suitab le g ear from 1st to
3rd ac c ord ing to the vehic le sp eed and the ac c elera tion you req uire.
When more ac c eleration is req uired in this p osition , p ress the ac c eler-
ator p ed al fully to the floor and hold that p ositio n. The transmission
will automatic ally d ownshift to 2nd or 1st g ear. Wh en you release the
p ed al, the transmission will return to the orig inal g ear p osition.

Page 199 of 322

7-24mph (km/h)
Vehicle type
PositionLS
134 (54)34 (54)
263 (101)62 (100)
3102 (164)101 (162)
NOTE In order to prevent over-revving during acceleration of the
vehicle, the transmission will automatically shift to the next high- est gear if the Maximum Allowable Speed for the current gear isexceeded. Similarly, in order to prevent over-revving during deceleration
of the vehicle, the transmission will remain in the current gear ifthe speed of the vehicle is in excess of the Maximum AllowableSpeed for the gear to which the selector lever has been moved. Driving tips
Always ap p ly the foot or p arking b rake when the veh ic le is
stop p ed in the “D ”, “3 ”, “2 ”, “1 ”, or “R ” p osition.
Always set the p arking b rake when p arking your vehi c le. Do not
hold the vehic le with only the transmission. Do not keep the vehic le in a stationary p osition on an up hill g rad e
b y using the “D ”, “3 ”, “2 ” or “1 ” p osition. Use the b rake instead .
Shift lock release
If the selec tor lever d oes not move from the “P ” p osition with the b rake
p ed al d ep ressed and the release b utton p ushed in an d the ig nition
switc h in the “ON ” p osition, p erform the following step s:
To overrid e the shift loc k:
1. Set the p arking b rake and stop the eng ine.

Page 204 of 322

Starting and operating7-29

CONTINUED –
c elerate the vehic le. When the ac c elerator p ed al is
released , the ve-
hic le will return to and maintain the p revious c rui sing sp eed .
To temporarily cancel the cruise control
There are four ways to c anc el the c ruise c ontrol te mp orarily:
Dep ress the b rake p ed al.
Pull the c ontrol lever in the “CANCEL ” d irec tion.
Dep ress the c lutc h p ed al (manual transmission vehic les only).
Shift the selec tor lever into the “N ” p osition (automatic transmis-
sion vehic les only).
If the vehic le sp eed d rop s 9 mp h (15 km/h) b elow th e p reset sp eed ,
the p reset sp eed will automatic ally c anc elled .
To resume the c ruise c ontrol after it has b een temp orarily c anc eled
and with vehic le sp eed of 25 mp h (40 km/h) or more, p ush the c ontrol
lever up ward in the “ACCEL, RESUME ” d irec tion to return to the orig i-
nal c ruising sp eed automatic ally. To turn off the cruise control
There are two ways to turn off the c ruise c ontrol: Push the main switc h ag ain.
Turn the ig nition switc h to the “ACC ” p osition (b ut only when the
vehic le is c omp letely stop p ed ). To change the cruising speed
n To increase the speed
1. Push the c ontrol lever up ward in the “ACCEL, RESUME ” d irec tion
and hold it until the vehic le reac hes the d esired s p eed .
The c ontrol lever c an b e used for inc reasing the c r uising sp eed slig ht-
ly. Pressing the c ontrol lever up ward in the “ACCEL, RESUME ” d irec -
tion inc reases the vehic le sp eed ab out 2 mp h (3.2 k m/h). Press the
c ontrol lever rep eated ly until the d esired sp eed is reac hed .
OR
1. Dep ress the ac c elerator p ed al to ac c elerate the v ehic le to the d e-
sired sp eed .
2. Push the c ontrol lever d ownward in the “SET, COAST ” d irec tion

Page 206 of 322

Starting and operating7-31

CONTINUED –
CAUTION
Never drive while the parking brake is set because this will cause
unnecessary wear on the brake linings. Before starting to drive,always make sure that the parking brake has been fully released.
To set the p arking b rake, p ress the b rake p ed al fir mly and hold it d own
while fully p ulling up the p arking b rake lever.
HS0137
Release button
To release the p arking b rake, p ull the lever up sli g htly, p ress the release
b utton, then lower the lever while keep ing the b utt on p ressed .
When the p arking b rake is set while the eng ine is r unning , the p arking
b rake warning lig ht c omes on. After starting the ve hic le, b e sure that the
warning lig ht has g one out b efore the vehic le is d r iven. Refer to the
“ Warning and ind ic ator lig hts ” sec tion (Chap ter 3).
When p arking your vehic le, always set the p arking b rake firmly and p ut
the shift lever in the “1 ” (1st) for an up g rad e or “R ” (Reverse) for a d own-
g rad e for manual transmission vehic les, or in the “P ” (Park) p osition for
automatic transmission vehic les.
Always set the p arking b rake firmly when p arking yo ur vehic le. Never
rely on the transmission alone to hold the vehic le.
For b etter p arking b rake p ower, d ep ress the b rake p ed al firmly while set-
ting the p arking b rake (Drum b rake only).

Page 217 of 322

7-42tor p ed al, b rake p ed al, and all other c ontrols op er
ate smoothly.
Clear away ic e and snow that has ac c umulated und er the fend ers to
avoid making steering d iffic ult. During severe wint er d riving , stop
when and where it is safe to d o so and c hec k und er the fend ers p eri-
od ic ally. n During cold weather below –4F ( –20 C)
If the eng ine is d iffic ult to start using the norma l method (without d e-
p ressing the ac c elerator p ed al), turn the ig nition switc h to the
“ START ” p osition while slig htly d ep ressing the ac c elerator p ed al.
n Parking in cold weather
WARNING
Snow can trap dangerous exhaust gases under your vehicle. Keep snow clear of the exhaust pipe and from around your
vehicle if you park the vehicle in snow with the engine running.
Do not use the p arking b rake when p arking for long p eriod s in c old
weather sinc e it c ould freeze in that p osition. Ins tead , ob serve the fol-
lowing :
1. Plac e the shift lever in “1 ” or “R ” for manual transmission vehic les,
and in “P ” for automatic transmission vehic les.
2. Use tire stop s und er the tires to p revent the veh ic le from moving .
When the vehic le is p arked in snow or when it snows , raise the wip er
b lad es off the g lass to p revent d amag e to them.
When the vehic le has b een left p arked after use on road s heavily c ov-
ered with snow, or has b een left p arked d uring a sn owstorm, ic ing
may d evelop on the b rake system, whic h c ould c ause p oor b raking
ac tion. Chec k for snow or ic e b uild up on the susp en sion, d isc b rakes
and b rake hoses und erneath the vehic le.
If there is c aked snow or ic e, remove it, b eing c ar eful not to d amag e
the d isc b rakes and b rake hoses and ABS harness. n Refueling in cold weather
To help p revent moisture from forming in the fuel s ystem and the risk
of its freezing , use of an antifreeze ad d itive in t he fuel tank is rec om-

Page 220 of 322

Starting and operating7-45

CONTINUED –
c orrec t tire size and typ e. All four tires should b
e of the same size,
c onstruc tion, c irc umferenc e, b rand and load rang e a nd you should nev-
er mix rad ial, b elted b ias or b ias tires sinc e this may result in d ang erous
hand ling c harac teristic s.
Rememb er to d rive with c are at all times reg ard less of the typ e of tires on
your vehic le. Tire chains
Driving on snowy g rad es or ic y road s may req uire th e use of tire c hains,
in whic h c ase p ut the c hains on the front wheels on ly. Use only SAE
c lass S typ e c hains that are of the c orrec t size fo r your tires so as not to
d amag e the vehic le b od y or susp ension.
When d riving with tire c hains, d rive at sp eed s b elo w 19 mp h (30 km/h).
When a temp orary sp are tire is on a front wheel, re p lac e the temp orary
sp are tire with the rear tire on the same sid e of t he vehic le, and then fit
c hains on the front tires.
Always use the utmost c are when d riving with tire c hains — overc onfi-
d enc e b ec ause you are d riving with tire c hains c oul d easily lead to a se-
rious ac c id ent.
Rocking the vehicle
If you must roc k the vehic le to free it from snow, sand , or mud , d ep ress the
ac c elerator p ed al slig htly and move the selec tor le ver b ac k and forth b e-
tween “D ” and “R ” rep eated ly. Do not rac e the eng ine. For the b est p ossib le
trac tion, avoid sp inning the wheels when trying to free the vehic le.
When the road surfac e is extremely slip p ery, you c a n ob tain b etter trac -
tion b y starting the vehic le with the transmission in 2nd than 1st (b oth for
MT and AT).
Refer to the “Automatic transmission ” sec tion in this c hap ter for informa-
tion on hold ing the transmission in 2nd p osition.
Corrosion protection
Refer to the “Corrosion p rotec tion ” sec tion (c hap ter 9).

Page:   < prev 1-10 11-20 21-30 31-40 next >