SUBARU IMPREZA 2000 2.G Owners Manual

Maintenance and service10-53
–
CONTINUED –

Front turn signal light Type A
HGA011BB
1. Remove the b olt sec uring the front turn sig nal li g ht assemb ly.
2. Remove the front turn sig nal lig ht assemb ly from the front b ump er
and remove the b ulb soc ket b y turning it c ounterc lo c kwise.
3. Remove the b ulb from the soc ket b y p ushing it in and turning
c loc kwise, then install a new b ulb .
4. Install the removed p arts in the reverse ord er of removal.
Type B
HG0194
1. Remove the front turn sig nal lig ht assemb ly mount ing sc rews using
the p hillip s sc rewd river.
2. Remove the lens from the front turn sig nal lig ht assemb ly.

10-543. Remove the b ulb from the soc ket b y p ushing it in
and turning
c ounterc loc kwise. Install a new b ulb .
4. Reinstall the lens to the front turn sig nal lig ht assemb ly and tig hten
the mounting sc rews.
Side turn signal light
OM-H0246
1. Pull the left sid e of the turn sig nal lig ht assem b ly while moving it for-
ward in relation to the vehic le.
2. Remove the b ulb hold er from the sid e turn sig nal lig ht assemb ly b y
turning it c ounterc loc kwise.
3. Pull the b ulb out of the soc ket. Install a new b u lb .
4. Set the b ulb hold er into the sid e turn sig nal lig ht assemb ly and turn it
c loc kwise until it loc ks.
5. Reinstall the sid e turn sig nal lig ht assemb ly on the sid e of the front
fend er.

Maintenance and service10-55
–
CONTINUED –

Rear combination lights Sedan and Coupe
OM-H0446
HG0241
1. Remove the sp are tire c over.
2. Remove the c lip from the rear trunk trim with a r eg ular sc rew d river.
3. Remove the nut sec uring the rear trunk trim.
OM-H0447
4. Op en the rear p ortion of the sid e trunk trim p ane l.
5. Remove the b ulb hold er from the rear c omb ination lig ht assemb ly
b y turning it c ounterc loc kwise.
6. Remove the b ulb from the soc ket b y p ushing it and turning c oun-
terc loc kwise. Install a new b ulb .
7. Set the b ulb hold er into the rear c omb ination lig ht assemb ly and
turn it c loc kwise until it loc ks.
8. Sec ure the rear trunk trim p anel with the nut and the c lip s.

10-56
Wagon
HG0195
1. Unlatc h the rear c omb ination lig ht c over b y p ulli ng the knob . Op en
the c over up .
OM-H0449
2. Remove the b ulb hold er from the rear c omb ination lig ht assemb ly
b y turning it c ounterc loc kwise.
3. Remove the b ulb from the soc ket b y p ushing it and turning c oun-
terc loc kwise. Install a new b ulb .
4. Set the b ulb hold er into the rear c omb ination lig ht assemb ly and
turn it c loc kwise until it loc ks.
5. Close the c over and latc h the loc k.

Maintenance and service10-57
–
CONTINUED –

License plate light
HG0198
1. Remove the mounting sc rews using a p hillip s sc rew d river.
2. Remove the c over and lens.
3. Pull the b ulb out of the soc ket. Install a new b u lb .
4. Reinstall the lens and c over.
5. Tig hten the mounting sc rews. Interior light, spot light
OM-H0251
OM-H0250
1. Remove the lens b y p rying the ed g e of the lens wi th a reg ular sc rew-
d river.
2. Pull the b ulb out of the soc ket. Install a new b u lb .
3. Reinstall the lens.

10-58
Dome/Rear map reading lights (if equipped)
CAUTION
While sitting in the vehicle, be sure to touch the metal frame of
the vehicle to allow all static electricity to be discharged prior to replacing bulbs. Always use recommended replacement bulbs.
HBB038BA
HBB037BA
1. Remove the d ome lig ht lens as follows:
Insert a small flat-tip p ed sc rewd river into the c en ter slot in the front ed g e
of the lens and lever the lens d ownward in suc h a w ay that it may b e
b owed and d iseng ag ed from the mounting tab s.
2. To rep lac e the d ome lig ht b ulb (c enter b ulb ): rem ove the d ome lig ht
b y p ulling it out of its retainer c lip s, then inser t a new b ulb into the retain-
er c lip s.
3. To rep lac e the map lig ht b ulb s: use a Phillip s he ad sc rewd river to re-
move the two mounting sc rews loc ated on either sid e of the lamp assem-
b ly. Pull the assemb ly d ownward out of the head line r. At this time, use
c are not to touc h the c irc uit b oard .
4. Remove the nec essary b ulb soc ket from the c irc uit b oard b y g rasp ing
it on the b ac ksid e of the lamp assemb ly and twistin g c ounterc loc kwise to
d iseng ag e.
5. Pull the b ulb out of the soc ket. Install a new b u lb b y p ushing it into the
soc ket.

Maintenance and service10-59
–
CONTINUED –
6. Reinstall the soc ket in the c irc uit b oard . Then,
fit the lamp assemb ly
b ac k into the head liner.
7. Reinstall the lens in the reverse ord er of remova l.

11
Specifications Specifications11-2
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dimensions 11-2
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maximum load limits 11-2
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine 11-2
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrical system 11-3
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Capacities 11-3
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tires 11-4
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuses and circuits 11-5
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bulb chart 11-8
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Vehicle identification 11-9
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11-2Specifications
These sp ec ific ations are sub jec t to c hang e without
notic e.
Dimensions
Overall leng th 172.2 in. (4,375 mm)
Overall wid th 67.1 in. (1,705 mm)
Overall heig ht 56.3 in. (1,430 mm)* 1
55.5 in. (1,410 mm)
Ground c learanc e 6.5 in. (165 mm)* 1
5.7 in. (145 mm)
Front tread 57.5 in. (1,460 mm), 57.9 in. (1,470 mm)*2
Rear tread 57.1 in. (1,450 mm), 57.5 in. (1,460 mm)*2
Wheelb ase 99.2 in. (2,520 mm)
* 1
: OUTBACK
* 2
: RS
Maximum load limits
Gross vehic le weig ht rating See the c ertific ation la b el attac hed
Gross axle weig ht rating to the d river ’s d oor jamb .
Engine
2500 c c Eng ine mod el EJ251
Eng ine typ e Horizontally op p osed , liq uid c ooled 4 c ylind er,
4 stroke g asoline eng ine
Eng ine d isp lac ement 149.9 c u in (2,457 c c )
Bore 3.92 in. (99.5 mm)
Stroke 3.11 in. (79.0 mm)
Comp ression ratio 10.0 : 1
Firing ord er 1 – 3 – 2 – 4

Specifications11-3
–
CONTINUED –
2200 c c
Eng ine mod el EJ222
Eng ine typ e Horizontally op p osed , liq uid c ooled 4 c ylind er,
4 stroke g asoline eng ine
Eng ine d isp lac ement 135.0 c u in (2,212 c c )
Bore 3.81 in. (96.9 mm)
Stroke 2.95 in. (75.0 mm)
Comp ression ratio 10.0 : 1
Firing ord er 1 — 3 — 2 — 4
Electrical system
Battery Typ e MT: 55D23L, AT: 75D23L
Reserve c ap ac ity MT: 99 min., AT: 118 min.
Cold c ranking amp ere MT: 356 amp ., AT: 520 amp .
Alternator 12V - 75A
Sp ark p lug s BKR6E-11 (NGK) RC10YC4, RC8YC4 (CHAMPION)
K20PR-U11 (NIPPONDENSO)
Sp ark p lug g ap 0.039 to 0.043 in. (1.0 to 1.1 mm) Capacities
2.5 Liter mod els Fuel tank 15.9 US g al (60 liter, 13.2 Imp g al)
Eng ine oil 4.2 US q t (4.0 liter, 3.5 Imp q t)
Transmission oil 3.7 US q t (3.5 liter, 3.1 Imp q t)
Automatic transmission fluid 9.8 US q t (9.3 liter, 8.2 Imp q t)
AT d ifferential g ear oil 1.3 US q t (1.2 liter, 1.1 I mp q t)
AWD rear d ifferential g ear oil 0.8 US q t (0.8 liter, 0.7 Imp q t)
Power steering fluid 0.7 US q t (0.7 liter, 0.6 Imp q t)
Eng ine c oolant 6.2 US q t (5.8 liter, 5.2 Imp q t)
2.2 Liter mod els Fuel tank 15.9 US g al (60 liter, 13.2 Imp g al)
Eng ine oil 4.2 US q t (4.0 liter, 3.5 Imp q t)