display SUBARU TRIBECA 2009 1.G Service Workshop Manual

AB(diag)-2
Basic Diagnostic Procedure
AIRBAG SYSTEM (DIAGNOSTICS)
1. Basic Diagnostic Procedure
A: PROCEDURE
Step Check Yes No
1CHECK WARNING LIGHT.
Check whether the airbag warning light in the
combination meter is lit.
Does the airbag warning light
illuminate?
Go to step 2.Perform the diag-
nosis according to
phenomenon of
the problem.
2READ DTC.
1) Turn the ignition switch to OFF.
2) Connect the Subaru Select Monitor to data
link connector.
3) Turn the ignition switch to ON, and the Sub-
aru Select Monitor power switch to ON.
4) Read the DTC. <Ref. to AB(diag)-36,
OPERATION, Read Diagnostic Trouble Code
(DTC).>
NOTE:If the communication function of the Subaru Se-
lect Monitor cannot be executed normally,
check the communication circuit. <Ref. to
AB(diag)-33, COMMUNICATION FOR INI-
TIALIZING IMPOSSIBLE, INSPECTION, Sub-
aru Select Monitor.>
5) Record all DTCs and freeze frame data.
Is DTC displayed? Go to step 3.<Ref. to AB(diag)-
40, Airbag Warn-
ing Light Fail-
ure.>Go to “Airbag
Wa r ni n g L ig h t Fa i l-
ure”.
3PERFORM DIAGNOSIS.
1) Judge the possible cause from “List of
Diagnostic Trouble Code” <Ref. to AB(diag)-
45, List of Diagnostic Trouble Code (DTC).>.
2) Inspect the DTC using “List of Diagnostic
Tr o u b l e C o d e ( D T C ) ” .
3) Repair the trouble cause.
4) Perform the clear memory mode. <Ref. to
AB(diag)-38, Clear Memory Mode.>
5) Perform the inspection mode. <Ref. to
AB(diag)-37, Inspection Mode.>
6) Read any other DTCs displayed.
Is DTC displayed? Perform the proce-
dure 1) to 5) in
step 3.
Finish the diagno-
sis.

AB(diag)-31
Subaru Select Monitor
AIRBAG SYSTEM (DIAGNOSTICS)
7. Subaru Select Monitor
A: OPERATION
1. READ DIAGNOSTIC TROUBLE CODE
(DTC)
When malfunction of airbag system occurs, the
DTC stored in airbag control module will be read
out.
1) Prepare the Subaru Select Monitor kit. <Ref. to
AB(diag)-8, SPECIAL TOOL, PREPARATION
TOOL, General Description.>
2) Connect the diagnosis cable to Subaru Select
Monitor.
3) Insert the cartridge to Subaru Select Monitor.
<Ref. to AB(diag)-8, SPECIAL TOOL, PREPARA-
TION TOOL, General Description.>
4) Connect the Subaru Select Monitor to data link
connector.
(1) Data link connector (1) is located in the low-
er portion of instrument panel (on the driver’s
side).
(2) Connect the diagnosis cable to data link
connector.
CAUTION:
Do not connect the scan tools except for Suba-
ru Select Monitor.
5) Turn the ignition switch to ON (engine OFF) and
turn the Subaru Select Monitor switch to ON.
6) On the «Main Menu» display screen, select the
{Each System Check} and press the [YES] key.
7) On the «System Selection Menu» display
screen, select the {Airbag System} and press the
[YES] key.
8) {Press the [YES] key after the {**MY AIRBAG
SYSTEM} is displayed.
9) On the «Airbag System» screen, select the
{DTC Display}, and then press the [YES] key.
NOTE:
•For details concerning operation procedure, re-
fer to the “SUBARU SELECT MONITOR OPERA-
TION MANUAL”.
•For details concerning DTCs, refer to List of Di-
agnostic Trouble Code (DTC). <Ref. to AB(diag)-
45, List of Diagnostic Trouble Code (DTC).>
ABS00111
ABS00112
EN-03693
(1) Power switch
ABS00114
(1)

AB(diag)-32
Subaru Select Monitor
AIRBAG SYSTEM (DIAGNOSTICS)
2. DISPLAY OF STATUS INFORMATION
Check the operating condition of each sensor in the event of malfunction in seat belt buckle switch and seat
position sensor, or when the seat belt buckle switch and seat position sensor has been replaced.
1) On the «Main Menu» display screen, select the {Each System Check} and press the [YES] key.
2) On the «System Selection Menu» display screen, select the {Airbag System} and press the [YES] key.
3) On the «Airbag System» display screen, select the {Status Data} and press the [YES] key.
The following table is for support data.
*1: The seat position is forward.
*2: The seat position is rearward.
*3: Displayed when data other than before and behind the seat, such as the breakdown etc, is input.
*4: Displayed when it is initial.
*5: Seat position sensor not supported
*6. Seat belt fastened
*7. Seat belt not fastened
*8: Displayed when data other than belt fastened or not fastened, such as breakdowns is input.
*9: Seat belt buckle switch not supported
*10: Passenger’s seat air bag operating state
*11: Passenger’s seat air bag non-operating state
NOTE:
For details concerning operation procedure, refer to the “SUBARU SELECT MONITOR OPERATION MAN-
UAL”.
3. CLEAR MEMORY MODE
Clear the DTC stored in the airbag control module after repairing airbag system. (After the breakdown is re-
covered, the breakdown code for completed recoveries are read out when the next breakdown occurs if the
memory clear work is not performed.)
1) On the «Main Menu» display screen, select the {Each System Check} and press the [YES] key.
2) On the «System Selection Menu» display screen, select the {Airbag System} and press the [YES] key.
3) On the {Airbag System} menu screen, select the {Clear Memory} and press the [YES] key.
4) When the “Clear Memory?” is shown on the screen, press the [YES] key.
5) When “Done” is displayed, turn the Subaru Select Monitor to OFF.
NOTE:
For details concerning operation procedure, refer to the “SUBARU SELECT MONITOR OPERATION MAN-
UAL”.
Item Display contents
Seat position sensor LHFr o nt p os it i on *1/Rear position *2 /Other *3/Initial Setting *3 /–– *5
Seat position sensor RH–– *5
Seat belt buckle switch LHBelted *6/Unbelted *7 /Other *8/Initial Setting *4 /–– *9
Seat belt buckle switch RHBelted *6/Unbelted *7 /Other *8/Initial Setting *4 /–– *9
Passenger’s airbag control statusON *10/OFF *11 /Initial Setting *4

AB(diag)-34
Subaru Select Monitor
AIRBAG SYSTEM (DIAGNOSTICS)
Step Check Yes No
1CHECK IGNITION SWITCH.Is the ignition switch ON? Go to step 2.Turn the ignition
switch to ON, and
select the airbag
mode using the
Subaru Select
Monitor.
2CHECK BATTERY.
1) Turn the ignition switch to OFF.
2) Measure the battery voltage.
Is the voltage more than 11 V? Go to step 3.Charge or replace
the battery.
3CHECK BATTERY TERMINAL.Is there poor contact at battery
terminal?
Repair or tighten
the battery termi-
nal.
Go to step 4.
4CHECK SUBARU SELECT MONITOR COM-
MUNICATION.
1) Turn the ignition switch to ON.
2) Using the Subaru Select Monitor, check
whether communication to other system can
be executed normally.
Are the system name and
model year displayed on Sub-
aru Select Monitor?
Go to step 9.Go to step 5.
5CHECK AIRBAG CONTROL MODULE CON-
NECTOR.
1) Turn the ignition switch to OFF, disconnect
the battery ground cable, and wait more than
20 seconds.
2) Is the connector of the air bag control mod-
ule (AB6) securely connected?
Is the connector of the air bag
control module securely con-
nected?
Go to step 6.Connect the con-
nector of the air-
bag control
module.
6CHECK SUBARU SELECT MONITOR COM-
MUNICATION.
1) Turn the ignition switch to OFF.
2) Disconnect the airbag control module con-
nector.
3) Turn the ignition switch to ON.
4) Check whether communication to other
systems can be executed normally.
Are the system name and
model year displayed on Sub-
aru Select Monitor?
Replace the airbag
control module.
<Ref. to AB-21,
Airbag Control
Module.>
Go to step 7.
7CHECK HARNESS CONNECTOR BETWEEN
EACH CONTROL MODULE AND DATA LINK
CONNECTOR.
1) Turn the ignition switch to OFF.
2) Disconnect the airbag control module,
ABSCM&H/U, ECM and TCM.
3) Measure the resistance between data link
connector and chassis ground.
Connector & terminal
(B40) No. 10 — Chassis ground:
Is the resistance more than 1
MΩ?
Go to step 8.Repair the har-
ness and connec-
tor between each
control module
and data link con-
nector. (Replace
the harness with-
out repairing the
airbag harness.)
8CHECK THE OUTPUT SIGNAL TO THE AIR-
BAG CONTROL MODULE.
1) Turn the ignition switch to ON in the status
of step 7.
2) Measure the voltage between data link con-
nector and chassis ground.
Connector & terminal
(B40) No. 10 (+) — Chassis ground (–):
Is the voltage less than 1 V? Go to step 9.Repair the har-
ness and connec-
tor between each
control module
and data link con-
nector. (Replace
the harness with-
out repairing the
airbag harness.)

AB(diag)-35
Subaru Select Monitor
AIRBAG SYSTEM (DIAGNOSTICS)
2. WITHOUT DTC
DETECTING CONDITION:
•Defective combination meter
•Open circuit of harness
TROUBLE SYMPTOM:
•Airbag warning light remains on.
•“NO TROUBLE CODE” will be displayed on the Subaru Select Monitor.
For detailed operation procedure, refer to “Airbag Warning Light Failure”. <Ref. to AB(diag)-40, Airbag Warn-
ing Light Failure.>
NOTE:
•For detailed operation procedure, refer to “Airbag Warning Light Failure”. <Ref. to AB(diag)-40, Airbag
Warning Light Failure.>
•When the airbag warning light is OFF and “NO TROUBLE CODE” is displayed on Subaru Select Monitor,
the system is in normal condition.
9CHECK THE HARNESS BETWEEN THE AIR-
BAG CONTROL MODULE AND DATA LINK
CONNECTOR.
1) Turn the ignition switch to OFF, disconnect
the battery ground cable, and wait more than
20 seconds.
2) Disconnect the connector (AB6) from air-
bag control module.
3) Connect the connector (1U) in the test har-
ness U to connector (AB6).
4) Measure the resistance between connector
(4U) in the test harness U and the data link
connector.
Connector & terminal
(4U) No. 18 — (B40) No. 10:
Is the resistance less than 10
Ω?
Go to step 10.Repair the har-
ness between the
airbag control
module and the
data link connec-
tor. Or replace the
airbag main har-
ness with the bulk-
head harness.
10 CHECK POWER SUPPLY CIRCUIT.
1) Turn the ignition switch to ON.
2) Measure the voltage between connector
(2U) in the test harness U and chassis ground.
Connector & terminal
(2U) No. 1 — Chassis ground:
(2U) No. 6 — Chassis ground:
Is the voltage more than 10 V? Go to step 11.Repair the har-
ness between the
airbag control
module and the
battery. Or replace
the airbag main
harness with the
bulkhead harness.
11 CHECK BETWEEN THE AIRBAG CONTROL
MODULE AND CHASSIS GROUND.
1) Turn the ignition switch to OFF.
2) Measure the resistance between connector
(2U) in the test harness U and chassis ground.
Connector & terminal
(2U) No. 10 — Chassis ground:
(2U) No. 11 — Chassis ground:
Is the resistance less than 10
Ω?
Go to step 12.Repair the har-
ness between the
airbag control
module and the
chassis ground. Or
replace the airbag
main harness with
the bulkhead har-
ness.
12 CHECK POOR CONTACT OF CONNECTOR.Is there poor contact in the
control module power supply,
ground circuit and data link
connector?
Repair the con-
nector. (Replace
the harness with-
out repairing the
airbag system
connector.)
Replace the only
airbag control
module. <Ref. to
AB-21, REMOVAL,
Airbag Control
Module.>
Step Check Yes No

AB(diag)-41
Airbag Warning Light Failure
AIRBAG SYSTEM (DIAGNOSTICS)
Step Check Yes No
1READ DTC.
Read the DTC. <Ref. to AB(diag)-31, READ
DIAGNOSTIC TROUBLE CODE (DTC),
OPERATION, Subaru Select Monitor.>
Is DTC displayed? Perform the diag-
nosis according to
DTC.
Go to step 2.
2CHECK POOR CONTACT.
1) Turn the ignition switch to OFF, disconnect
the battery ground cable, and wait more than
20 seconds.
2) Confirm that there is solid connection
between the airbag control module and con-
nector (AB6).
Is there poor contact in con-
nector (AB6)?
If the poor contact
of the connector is
not fixed, replace
the airbag main
harness with body
harness or replace
the airbag control
module. <Ref. to
AB-21, Airbag
Control Module.>
Go to step 3.
3CHECK AIRBAG MAIN HARNESS.
1) Remove the instrument panel lower cover
and disconnect the connectors (AB7) and
(AB2).
2) Remove the console side cover lower on
the passenger's side and disconnect the con-
nectors (AB10) and (AB9).
3) Disconnect the connector (AB6) from air-
bag control module, and connect the connector
(1U) in the test harness U.
4) Connect the battery ground terminal and
turn the ignition switch to ON.
5) Connect the connectors (7U) and (8U) in
the test harness U.
NOTE:After the fault has been cleared, disconnect the
connectors (7U) and (8U).
Does the airbag warning light
go off?
Go to step 4.Go to step 5.
4CHECK GROUND CIRCUIT.
1) Turn the ignition switch to OFF, disconnect
the battery ground cable, and wait more than
20 seconds.
2) Disconnect the connector (AB6) from air-
bag control module.
3) Connect the connector (1U) in the test har-
ness U to body harness connector (AB6).
4) Measure the resistance between connector
(2U) in the test harness U and chassis ground.
Connector & terminal
(2U) No. 10 — Chassis ground:
(2U) No. 11 — Chassis ground:
Is the resistance less than 10
Ω?
Replace the airbag
control module.
<Ref. to AB-21,
Airbag Control
Module.>
Repair the chas-
sis ground circuit.
5CHECK AIRBAG MAIN HARNESS AND
BULKHEAD HARNESS.
1) Disconnect the connectors (7U) and (8U).
2) Remove the combination meter.
3) Measure the resistance between connector
(i11) and connector (2U) in the test harness U.
Connector & terminal
(2U) No. 7 — (i11) No. 12:
Is the resistance less than 10
Ω?
Check the combi-
nation meter.
Go to step 6.

AB(diag)-44
Airbag Warning Light Failure
AIRBAG SYSTEM (DIAGNOSTICS)
Step Check Yes No
1CHECK COMBINATION METER.
Tu r n t h e i g n i t i o n s w i t c h t o O N , a n d c o n f i r m t h a t
warning light of combination meter is turned
on.
Do warning lights except for
airbag turn on?
Go to step 2.Check the combi-
nation meter.
2CHECK DTC.
Read the DTC. <Ref. to AB(diag)-31, READ
DIAGNOSTIC TROUBLE CODE (DTC),
OPERATION, Subaru Select Monitor.>
Is DTC displayed? Perform the diag-
nosis according to
DTC.
Go to step 3.
3CHECK FUSE NO. 5 (IN MAIN FUSE BOX).
Remove the fuse No. 5 and perform visual
inspection.
Is the fuse No. 5 (in main fuse
box) blown out?
Replace the fuse
No. 5. If the fuse
No. 5 is blown out
again, go to step
4.
Go to step 4.
4CHECK AIRBAG WARNING LIGHT CIRCUIT
(IN COMBINATION METER).
1) Turn the ignition switch to OFF, disconnect
the battery ground cable, and wait more than
20 seconds.
2) Disconnect the connector (AB1) from
(B31).
3) Connect the battery ground terminal and
turn the ignition switch to ON.
Does airbag warning light turn
on?
Go to step 5.Check the combi-
nation meter.
5CHECK AIRBAG MAIN HARNESS.
1) Turn the ignition switch to OFF, disconnect
the battery ground cable, and wait more than
20 seconds.
2) Connect the connector (AB1) to (B31).
3) Disconnect the connector (AB6) from air-
bag control module.
4) Connect the battery ground terminal and
turn the ignition switch to ON.
Does airbag warning light turn
on?
Replace the airbag
control module.
<Ref. to AB-21,
Airbag Control
Module.>
Replace the airbag
main harness with
bulkhead harness.

AB(diag)-45
List of Diagnostic Trouble Code (DTC)
AIRBAG SYSTEM (DIAGNOSTICS)
13.List of Diagnostic Trouble Code (DTC)
A: LIST
DTC Display Content of diagnosis Reference target
11 Driver’s Airbag failure • Airbag main harness circuit is open, shorted
or shorted to ground.
•Airbag module harness (Driver's side) circuit
is open, shorted or shorted to ground.
•Roll connector circuit is open, shorted or
shorted to ground.
•Airbag control module is faulty.
•Driver's airbag module is faulty.
<Ref. to AB(diag)-49, DTC 11 DRIVER'S
AIRBAG FAILURE, Diagnostic Chart
with Trouble Code.>
12 Passenger's Airbag failure • Airbag main harness circuit is open, shorted
or shorted to ground.
•Airbag module harness (Passenger's side)
circuit is open, shorted or shorted to ground.
•Airbag control module is faulty.
•Passenger's airbag module is faulty.
<Ref. to AB(diag)-53, DTC 12 PASSEN-
GER'S AIRBAG FAILURE, Diagnostic
Chart with Trouble Code.>
15 Driver’s Airbag failure • Airbag main harness circuit (Driver’s side) is
shorted to power supply.
•Airbag module harness circuit (Driver’s side)
is shorted to power supply.
•Roll connector is shorted to power supply.
•Airbag control module is faulty.
•Driver’s airbag module is faulty.
<Ref. to AB(diag)-56, DTC 15 DRIVER'S
AIRBAG FAILURE, Diagnostic Chart
with Trouble Code.>
16 Passenger's Airbag failure • Airbag main harness circuit (Passenger's
side) is shorted to power supply.
•Airbag module harness circuit (Passenger's
side) is shorted to power supply.
•Airbag control module is faulty.
•Passenger's airbag module is faulty.
<Ref. to AB(diag)-59, DTC 16 PASSEN-
GER'S AIRBAG FAILURE, Diagnostic
Chart with Trouble Code.>
21 Airbag ECU failure Airbag control module is faulty. <Ref. to AB(diag)-61, DTC 21 AIRBAG
ECU FAILURE, Diagnostic Chart with
Tr o u b l e C o d e . >
22 Front Airbag Firing output Front airbag module and seat belt pretensioner
(LH/RH) are inflated.
<Ref. to AB(diag)-62, DTC 22 FRONT
AIRBAG FIRING OUTPUT, Diagnostic
Chart with Trouble Code.>
23 Connector to Airbag ECU
failure
Connection of (AB6), (AB17) and (AB18) to air-
bag control module is improper.
<Ref. to AB(diag)-63, DTC 23 CONNEC-
TOR TO AIRBAG ECU FAILURE, Diag-
nostic Chart with Trouble Code.>
24 IG1 open • Airbag control module is faulty.
•Airbag main harness circuit is open.
•Fuse No. 12 (in joint box) is blown.
•Airbag rear harness circuit is open.
<Ref. to AB(diag)-64, DTC 24 IG1
OPEN, Diagnostic Chart with Trouble
Code.>
25 IG2 open • Airbag control module is faulty.
•Airbag main harness circuit is open.
•Fuse No. 25 (in joint box) is blown.
•Airbag rear harness circuit is open.
<Ref. to AB(diag)-66, DTC 25 IG2
OPEN, Diagnostic Chart with Trouble
Code.>
26 Passenger's Airbag indi-
cator failure
•Passenger's airbag indicator is faulty.
•Airbag control module is faulty.
•Airbag main harness circuit is open, shorted
or shorted to ground.
•Body harness circuit is open.
<Ref. to AB(diag)-68, DTC 26 PASSEN-
GER'S AIRBAG INDICATOR FAILURE,
Diagnostic Chart with Trouble Code.>
27 ODS Communication error • Occupant detection control module communi-
cation is faulty.
•Airbag rear harness circuit is open, shorted,
shorted to ground or shorted to power supply.
•Occupant detection harness is faulty.
•Airbag control module is faulty.
•Occupant detection system is faulty.
<Ref. to AB(diag)-70, DTC 27 ODS
COMMUNICATION ERROR, Diagnostic
Chart with Trouble Code.>

AB(diag)-46
List of Diagnostic Trouble Code (DTC)
AIRBAG SYSTEM (DIAGNOSTICS)
29 ODS failure • Occupant detection sensor is faulty.
•Occupant detection control module is faulty.
•Occupant detection harness is faulty.
•Fuse No. 25 (in joint box) is blown.
Refer to “Occupant Detection System”
for details on DTC 29. <Ref. to OD(diag)-
29, DTC 29 ODS FAILURE, Diagnostic
Procedure with Diagnostic Trouble Code
(DTC).>
2A ODS Calibration error System calibration (Rezeroing) of the occupant
detection system was not ended normally.
Refer to “Occupant Detection System”
for details on DTC 2A. <Ref. to
OD(diag)-26, DTC 2A OCCUPANT
DETECTION CALIBRATION FAILURE,
Diagnostic Procedure with Diagnostic
Tr o u b l e C o d e ( D T C ) . >
2B ODS System Wrong error • Wrong airbag control module was installed.
•Wrong occupant detection system was
installed.
•Occupant detection system is faulty.
Refer to “Occupant Detection System”
for details on DTC 2B. <Ref. to
OD(diag)-26, DTC 2B ODS ERRONE-
OUS PARTS, Diagnostic Procedure with
Diagnostic Trouble Code (DTC).>
2C Belt Tension Sensor fail-
ure
•Passenger’s seat belt tension sensor is faulty.
•Occupant detection system is faulty.
•Airbag rear harness circuit is open, shorted,
shorted to ground or shorted to power supply.
•Occupant detection harness is faulty.
Refer to “Occupant Detection System”
for details on DTC 2C. <Ref. to
OD(diag)-27, DTC 2C BELT TENSION
SENSOR FAILURE, Diagnostic Proce-
dure with Diagnostic Trouble Code
(DTC).>
31 Front Sub Sensor RH fail-
ure
•Front sub sensor harness (RH) circuit is open
or shorted.
•Front sub sensor (RH) is faulty.
•Airbag control module is faulty.
<Ref. to AB(diag)-72, DTC 31 FRONT
SUB SENSOR RH FAILURE, Diagnostic
Chart with Trouble Code.>
32 Front Sub Sensor LH fail-
ure
•Front sub sensor harness (LH) circuit is open
or shorted.
•Front sub sensor (LH) is faulty.
•Airbag control module is faulty.
<Ref. to AB(diag)-74, DTC 32 FRONT
SUB SENSOR LH FAILURE, Diagnostic
Chart with Trouble Code.>
33 Front Sub Sensor RH fail-
ure
Fr o nt su b se ns or ( RH) i s fa u lt y. < Re f. t o A B ( d ia g ) - 76 , D TC 3 3 F RONT
SUB SENSOR RH FAILURE, Diagnostic
Chart with Trouble Code.>
34 Front Sub Sensor LH fail-
ure
Fr o nt su b se ns or ( RH) i s fa u lt y. < Re f. t o A B ( d ia g ) - 76 , D TC 3 4 F RONT
SUB SENSOR LH FAILURE, Diagnostic
Chart with Trouble Code.>
36 Seat Position Sensor LH
failure
•Driver's seat position sensor is faulty.
•Airbag control module is faulty.
•Airbag rear harness LH circuit is open,
shorted or shorted to ground.
<Ref. to AB(diag)-77, DTC 36 SEAT
POSITION SENSOR LH FAILURE,
Diagnostic Chart with Trouble Code.>
37 Buckle Switch RH failure • Passenger's seat buckle switch circuit is
open, shorted or shorted to ground.
•Occupant detection system is faulty.
•Occupant detection harness is faulty.
Refer to “Occupant Detection System”
for details on DTC 37. <Ref. to OD(diag)-
30, DTC 37 BUCKLE SWITCH RH FAIL-
URE, Diagnostic Procedure with Diag-
nostic Trouble Code (DTC).>
38 Buckle Switch LH failure • Driver's seat buckle switch circuit is open,
shorted or shorted to ground.
•Airbag rear harness LH circuit is open,
shorted or shorted to ground.
•Airbag control module is faulty.
<Ref. to AB(diag)-79, DTC 38 BUCKLE
SWITCH LH FAILURE, Diagnostic Chart
with Trouble Code.>
39 Seatbelt Warning failure • Airbag control module is faulty.
•Body integrated module is faulty.
•Harness circuits between body integrated
module and air bag control module are open,
shorted or shorted to ground.
<Ref. to AB(diag)-81, DTC 39 SEAT-
BELT WARNING FAILURE, Diagnostic
Chart with Trouble Code.>
41 Side Airbag RH failure • Side airbag harness (RH) circuit is faulty.
•Side airbag module (RH) is faulty.
•Airbag control module is faulty.
<Ref. to AB(diag)-83, DTC 41 SIDE AIR-
BAG RH FAILURE, Diagnostic Chart
with Trouble Code.>
DTC Display Content of diagnosis Reference target

AB(diag)-47
List of Diagnostic Trouble Code (DTC)
AIRBAG SYSTEM (DIAGNOSTICS)
42 Side Airbag LH failure • Side airbag harness (LH) circuit is faulty.
•Side airbag module (LH) is faulty.
•Airbag control module is faulty.
<Ref. to AB(diag)-86, DTC 42 SIDE AIR-
BAG LH FAILURE, Diagnostic Chart with
Tr o u b l e C o d e . >
45 Side Airbag RH failure • Side airbag harness (RH) is shorted to power
supply.
•Airbag control module is faulty.
<Ref. to AB(diag)-89, DTC 45 SIDE AIR-
BAG RH FAILURE, Diagnostic Chart
with Trouble Code.>
46 Side Airbag LH failure • Side airbag harness (LH) is shorted to power
supply.
•Airbag control module is faulty.
<Ref. to AB(diag)-91, DTC 46 SIDE AIR-
BAG LH FAILURE, Diagnostic Chart with
Tr o u b l e C o d e . >
51 Side Airbag Sensor RH
failure
•Side airbag sensor (RH) is faulty.
•Side airbag harness (RH) circuit is faulty.
•Airbag control module is faulty.
<Ref. to AB(diag)-93, DTC 51 SIDE AIR-
BAG SENSOR RH FAILURE, Diagnostic
Chart with Trouble Code.>
52 Side Airbag Sensor LH
failure
•Side airbag sensor (LH) is faulty.
•Side airbag harness (LH) circuit is faulty.
•Airbag control module is faulty.
<Ref. to AB(diag)-95, DTC 52 SIDE AIR-
BAG SENSOR LH FAILURE, Diagnostic
Chart with Trouble Code.>
53 Side Airbag Sensor RH
failure
Side airbag sensor (RH) is faulty. <Ref. to AB(diag)-97, DTC 53 SIDE AIR-
BAG SENSOR RH FAILURE, Diagnostic
Chart with Trouble Code.>
54 Side Airbag Sensor LH
failure
Side airbag sensor (LH) is faulty. <Ref. to AB(diag)-97, DTC 54 SIDE AIR-
BAG SENSOR LH FAILURE, Diagnostic
Chart with Trouble Code.>
55 Side Curtain Airbag Firing
output
•Side airbag module is deployed.
•Curtain airbag module is deployed.
<Ref. to AB(diag)-97, DTC 55 SIDE
CURTAIN AIRBAG FIRING OUTPUT,
Diagnostic Chart with Trouble Code.>
56 Curtain Airbag Sensor RH
failure
•Curtain airbag sensor (RH) is faulty.
•Curtain airbag harness (RH) circuit is faulty.
•Airbag control module is faulty.
<Ref. to AB(diag)-98, DTC 56 CURTAIN
AIRBAG SENSOR RH FAILURE, Diag-
nostic Chart with Trouble Code.>
57 Curtain Airbag Sensor LH
failure
•Curtain airbag sensor (LH) is faulty.
•Curtain airbag harness (LH) circuit is faulty.
•Airbag control module is faulty.
<Ref. to AB(diag)-101, DTC 57 CUR-
TA I N A I R B A G S E N S O R L H FA I L U R E ,
Diagnostic Chart with Trouble Code.>
58 Curtain Airbag Sensor RH
failure
Curtain airbag sensor (RH) is faulty. <Ref. to AB(diag)-103, DTC 58 CUR-
TAIN AIRBAG SENSOR RH FAILURE,
Diagnostic Chart with Trouble Code.>
59 Curtain Airbag Sensor LH
failure
Curtain airbag sensor (LH) is faulty. <Ref. to AB(diag)-103, DTC 59 CUR-
TA I N A I R B A G S E N S O R L H FA I L U R E ,
Diagnostic Chart with Trouble Code.>
61 Belt Pretensioner RH fail-
ure
•Seat belt pretensioner (RH) circuit is open,
shorted or shorted to ground.
•Airbag control module is faulty.
•Pretensioner is faulty.
•Pretensioner harness is faulty.
<Ref. to AB(diag)-104, DTC 61 BELT
PRETENSIONER RH FAILURE, Diag-
nostic Chart with Trouble Code.>
62 Belt Pretensioner LH fail-
ure
•Seat belt pretensioner (LH) circuit is open,
shorted or shorted to ground.
•Airbag control module is faulty.
•Pretensioner is faulty.
•Pretensioner harness is faulty.
<Ref. to AB(diag)-107, DTC 62 BELT
PRETENSIONER LH FAILURE, Diag-
nostic Chart with Trouble Code.>
65 Belt Pretensioner RH fail-
ure
•Seat belt pretensioner (RH) circuit is shorted
to power supply.
•Pretensioner is faulty.
•Pretensioner harness is faulty.
•Airbag control module is faulty.
<Ref. to AB(diag)-110, DTC 65 BELT
PRETENSIONER RH FAILURE, Diag-
nostic Chart with Trouble Code.>
66 Belt Pretensioner LH fail-
ure
•Seat belt pretensioner (LH) circuit is shorted
to power supply.
•Pretensioner is faulty.
•Pretensioner harness is faulty.
•Airbag control module is faulty.
<Ref. to AB(diag)-112, DTC 66 BELT
PRETENSIONER LH FAILURE, Diag-
nostic Chart with Trouble Code.>
DTC Display Content of diagnosis Reference target