heating SUZUKI BALENO 1999 1.G Owners Manual

60G-74E
INSTRUMENT PANEL

INSTRUMENT PANEL

Instrument Panel 5-1

Instrument Cluster 5-2

Warning and Indicator Lights 5-3

Speedometer/Odometer/Tripmeter (if equipped) 5-5

Tachometer (if equipped) 5-6

Fuel Gauge 5-6

Temperature Gauge 5-6

Hazard Warning Switch 5-7

Rear Window Defroster Switch (if equipped) 5-7

Cigarette Lighter (if equipped) 5-7

Ashtray 5-8

Glove Box 5-8

Heating System (if equipped) 5-9

System Operating Instructions 5-10

Air Conditioning System (if equipped) 5-13

System Operating Instructions 5-13

37

INSTRUMENT PANEL
60G-74E

INSTRUMENT PANEL

1. Instrument cluster

2. Ignition switch

3. Lighting switch/Turn signal and

dimmer switch

4. Windscreen wiper and washer

switch

5. Hazard warning switch

6. Rear window defroster switch

(if equipped)

7. Other switches (if equipped)

8. Heater control panel

9. Audio system (if equipped)

10. Cigarette lighter (if equipped)

11. Ashtray

12. Bonnet release

13. Center ventilator

14. Side ventilator

15. Side defroster

16. Glove box

17. Fuse box

18. Cup holder (if equipped)

5-1
38

60G-74E
INSTRUMENT PANEL

TACHOMETER (if equipped)

FUEL GAUGE
TEMPERATURE GAUGE

60G-05-004

The tachometer indicates engine speed in

revolutions per minute.

Never drive with the engine speed

indicator in the red zone or severe

engine damage can result.
60G-05-005

This gauge gives an approximate indication

of the amount of fuel in the fuel tank as shown

in figure. "P stands for full and "E" stands for

empty.

If the indicator gets in the red zone, refill the

tank as soon as possible.

Note:

This vehicle has fuel gauge of new design.

Even when the ignition switch is "OFF", the

needle will not return to "E" position but will

show the reading.
60G-05-006

When the ignition switch is on, this gauge

indicates the engine coolant temperature.

Under normal driving conditions, the indicator

should stay within the normal, acceptable

temperature range between "H" and "C". If the

indicator approaches "H", and maintains that

reading, overheating is indicated. Follow the

instructions for engine overheating in the

EMERGENCY REMEDIES section.

CAUTION

Continuing to drive the vehicle when

engine overheating is indicated, can

result in severe engine damage.

43

5-6

INSTRUMENT PANEL

60G-74E

HAZARD WARNING SWITCH
REAR WINDOW DEFROSTER SWITCH CIGARETTE LIGHTER (if equipped)

(if equipped)

60G-05-007

Push in the hazard warning switch to activate

the hazard warning lights. All four turn signal

lights and both turn signal indicators will flash

simultaneously. To turn off the lights, push the

switch again.

Use the hazard warning lights to warn other

traffic during emergency parking or when your

vehicle could otherwise become a traffic

hazard.
60G-05-008

When the rear window is misted, push this

switch to clear the window. An indicator light

will be lit when the defroster is on. The

defroster will only work when the ignition

switch is in the "ON position. To turn off the

defroster, push the switch again.

CAUTION

The rear window defroster uses a large

amount of electricity. Be sure to turn

off after the window has become clear.
60G-05-009

To use the cigarette lighter, push it all the way

into the receptacle and release it. It will

automatically heat up and will pop out to its

normal position when it is ready for use.

5-7
44

60G-74E
INSTRUMENT PANEL

ASHTRAY

GLOVE BOX

60G-05-010

843-05-011E

Front Ashtray

To remove the front panel ashtray for cleaning,

push down on the metal plate, and pull the

ashtray completely out of its holder.
Rear Ashtray

To remove the rear ashtray, push down on the

tongue and pull the ashtray out of its holder.

Make sure tobacco is fully extinguished

before closing the ashtray. Never throw

waste in the ashtray: it could create a

fire hazard.
60G-05-011

To open the glove box, pull the latch lever.

To close it, push the lid until It latches securely.

If a lock is equipped on the latch lever, lock

the glove box by inserting the key and turning

it clockwise and unlock the glove box by

turning the key counterclockwise.

Never drive with the glove box lid open.

It could cause injury if an accident

occurs.

45

5-8

INSTRUMENT PANEL
60G-74E

HEATING SYSTEM (if equipped)

The heating system provides heating

demisting, and ventilation.

a. Windscreen defroster

b. Side defroster

c. Side outlet

d. Center outlet

e. Floor outlet

60G-05-012

@

RECIRCULATED AIR FRESH AIR

60G-05-013

5-9
46

60G-74E
INSTRUMENT PANEL

Description of Controls

Function Buttons ©: These buttons are used

to select one of the functions described below:

VENTILATION ©: Temperature-

controlled air comes out of the

center and side air outlets.

BI-LEVEL ®: Temperature-

controlled air comes out of the floor

outlets and cooler air comes out of

the center and side outlets. When

the temperature control lever is in

the fully "COOL" position or fully

"HOT" position, however, the air from

the floor outlets and the air from the

center and side outlets will be the

same temperature.

HEAT ©: Temperature-controlled air

comes out of the floor outlets.

HEAT & DEFROST ©: Tempera-

ture-controlled air comes out of the

floor outlets, the windscreen de-

froster outlets, and the side defroster

outlets.
DEFROST ©: Temperature-

controlled air comes out of the

windscreen defroster outlets and the

side defroster outlets.

Air Intake Lever ©:This lever is used to select

between circulating outside air (FRESH AIR)

or recirculating inside air (RECIRCULATED

AIR).

Temperature Control Lever ©: This lever is

used to control the temperature of the air that

comes out of the air outlets.

Fan switch ©: This switch is used to turn on

the fan and to select fan speed. There are five

positions: OFF, LOW, MEDIUM, MEDIUM

HIGH and HIGH.
SYSTEM OPERATING INSTRUCTIONS

60G-05-014

Natural Ventilation

Push the "VENTILATION" button and move the

air intake lever to "FRESH AIR", the

temperature control lever to the desired

temperature position, and the fan switch to

"OFF. Fresh air will flow through the vehicle

when it is moving.

70F-03-032

47
5-10

INSTRUMENT PANEL

60G-74E

60G-05-015

Forced Ventilation

The lever settings are the same as for natural

ventilation except you move the fan switch to

a position other than "OFF".
1

I
*
A/C

1
OFF
| | ••

= =11

60G-05-016

Normal Heating (Using outside air)

Push the "HEAT" button and move the air

intake lever to "FRESH AIR", the temperature

control lever to the desired temperature

position, and the fan switch to the desired fan

speed position. Moving the fan switch to a

higher fan speed position increases heating

efficiency.
60G-05-017

Quick Heating (Using recirculated air)

The lever settings are the same as for normal

heating except you move the air intake lever

to "RECIRCULATED AIR". If you use this

heating method for an extended period of time,

the air in the vehicle can become

contaminated and the windows can become

misty. Therefore, use this method only for quick

heating and change to the normal heating

method as soon as possible.

5-11
70F-03-031
70F-03-030
70F-03-029

OTHER CONTROLS AND EQUIPMENTS
60G-74E

PARKING BRAKE LEVER

63B-06-001E

The parking brake lever is located between

the seats. To apply the parking brake, hold the

brake pedal down and pull the parking brake

lever all the way up.
63B-06-002E

To release the parking brake, hold the brake

pedal down, pull up slightly on the parking

brake lever, push the button on the end of the

lever with your thumb, and lower the lever to

its original position.
Never drive your vehicle with the

parking brake on: rear brake

effectiveness can be reduced from

over heating, brake life may be

shortened, or permanent brake

damage may result.

If the parking brake does not hold

the vehicle securely or does not fully

release, have your vehicle inspected

immediately by an authorized

MARUTI dealer.

Always apply the parking brake fully

before leaving your vehicle or it may

move, causing injury or damage. When

parking, make sure the gear shift lever

is left in first gear or reverse.

Remember, even though the

transmission is in gear, you must

always apply the parking brake fully.

6-1
54

60G-74E
OTHER CONTROLS AND EQUIPMENT

PEDALS

GEAR LEVER

60G-06-001

Clutch Pedal ©

The clutch pedal is used to disengage the drive

to the wheels when starting the engine,

stopping, or shifting the transmission lever.

Depressing the pedal disengages the clutch.

CAUTION

Do not drive with your foot resting on

the clutch pedal. It could result in

excessive clutch wear, clutch damage,

or unexpected loss of engine braking.
Brake Pedal ®

Your MARUTI vehicle is equipped with front

disc brakes and rear drum brakes. Depressing

the brake pedal applies both sets of brakes.

You may hear occasional brake squeal when

you apply the brakes. This is a normal

condition caused by environmental factors

such as cold, wet, snow, etc.

If brake squeal is excessive and occurs

each time the brakes are applied, you

should have the brakes checked by

your MARUTI dealer.

A WARNING

Do not "ride" the brakes by applying

them continuously or resting your foot

on the pedal. This will result in

overheating of the brakes which could

cause unpredictable braking action,

longer stopping distances, or

permanent brake damage.

Accelerator Pedal ®

This pedal controls the speed of the engine.

Depressing the accelerator pedal increases

power output and speed.
70F-04-005E

The gear change pattern is shown in the

illustration. For details on how to use the

transmission, refer to USING THE

TRANSMISSION in the OPERATING YOUR

VEHICLE section.

55

6-2

60G-74E
OPERATING YOUR VEHICLE

CATALYTIC CONVERTER

(if equipped)

70F-05-005

The purpose of the catalytic converter installed

on your vehicle is to convert exhaust pollutants

to harmless water vapour, carbon dioxide, and

nitrogen. Use of leaded fuel in vehicles

equipped with catalytic converters is

prohibited, because lead deactivates the

pollutant-reducing components of the catalyst

system.

It is very important to keep the engine properly

tuned. Engine misfiring, which can result from

an improperly tuned engine, may cause

overheating of the catalyst. This may result in

permanent heat damage to the catalyst and

other vehicle components.
CAUTION

To minimize the possibility of catalyst

or other vehicle damage:

• Maintain the engine in the proper

operating condition.

• In the event of an engine

malfunction, particularly one

involving engine misfire or other

apparent loss of performance, have

the vehicle serviced promptly.

• Do not turn off the engine or

interrupt the ignition when the

transmission is in gear and the

vehicle is in motion.

• Do not try to start the engine by

pushing or towing the vehicle, or

coasting down a hill.

• Do not idle the engine with any spark

plug wires disconnected or

removed, such as during diagnostic

testing.

• Do not idle the vehicle for prolonged

periods if idling seems rough or

there are other malfunctions.

• Do not allow the fuel tank to get near

the empty level.
60Q-07-002E

Be careful where you park and drive;

the catalytic converter and other

exhaust components can get very hot.

As with any vehicle, do not park or

operate this vehicle in areas where

combustible materials such as dry

grass or leaves can come in contact

with a hot exhaust system.

7-6

OPERATING YOUR VECHILE

60G-74E

IMPROVING FUEL ECONOMY

The following instructions will help you improve

fuel economy.

Avoid excessive idling:

If you are to wait for more than a minute while

you are parked, stop the engine and start it

again later. When warming up a cold engine,

allow the engine to idle until the temperature

gauge pointer comes up to the "C" position. In

this position, the engine is sufficiently warm

for starting off.

Avoid "fast" starts:

Fast starts away from lights or stop signs will

consume fuel unnecessarily and shorten

engine life. Start off slowly.

Avoid unnecessary stops:

Avoid unnecessary deceleration and stopping.

Try to maintain a slow, steady speed whenever

possible. Slowing down and then accelerating

again uses more fuel.

Keep a steady cruising speed:

Keep as constant a speed as road and traffic

conditions will permit.
Air Outlet side

(Facing up)

60G-09-010

Keep the air cleaner clean:

A dirty air cleaner will cause the carburation

system to supply too much fuel to the engine

for the amount of air being supplied. The result

is waste of fuel due to incomplete combustion.

Keep weight to a minimum:

The heavier the load, the more fuel the vehicle

consumes. Take out any luggage or cargo

when it is not necessary.

Keep tyre pressures correct:

Under-inflation of the tyres can waste fuel due

to increased running resistance of the tyres.

Keep your tyres inflated to the correct pressure

shown on the label on the driver's side door

or door lock pillar.
TRAILER TOWING

Your MARUTI was originally designed to carry

people and a normal amount of cargo, not to

tow a trailer. Maruti does not recommend you

use your vehicle to tow a trailer.Towing a trailer

can adversely affect handling, durability, and

fuel economy.

7-7

72
71

60G-74E
DRIVING TIPS AND SAFE DRIVING

Snow Chains

If you must use snow chains to increase tyre

traction, observe the following precautions:

• Choose a safe place away from traffic to

install the chains.

• When installing the chains carefully follow

the manufacturer's instructions.

• Install the chains on the front tyres.

• With the chains on, drive only at slow and

moderate speeds.

• If Your Vehicle Gets Stuck

If your vehicle gets stuck in snow, mud, or

sand, follow the directions below:

1) Change back and forth between first gear

and reverse. This will create a rocking

motion which may give you enough

momentum to free the vehicle. Press

gently on the accelerator to keep wheel

spin to a minimum. Remove your foot from

the accelerator while changing gear.

Do not race the engine. Excessive wheel

spin will cause the tyres to dig deeper,

making it more difficult to free the vehicle.

2) If your vehicle remains stuck after a few

minutes of rocking, get another vehicle to

pull you out.
Do not allow anyone to stand near the

vehicle when you are rocking it, and do

not spin the wheels faster than an

indicated 40 km/h on the speedometer.

Personal injury and/or vehicle damage

may result from spinning the wheels

too fast.

CAUTION

Do not continue rocking the vehicle for

more than a few minutes. Prolonged

rocking can cause engine overheating

or transmission damage.

DRIVING ON WET ROADS

CAUTION

When driving on wet roads, avoid driv-

ing through large amount of standing

water on the road. Large amount of

water entering the engine compart-

ment may cause damage to the engine

and or electrical components.

If stuck in deep water, do not start till

water level drops.

Water Is incompressible substance,

water inside engine is harmful to

the engine."
Make sure your tyres are in good

condition and always maintain the

specified tyre pressure. Refer to

"TYRES" in the "INSPECTION AND

MAINTENANCE" section for details.

Do not use tyres other than those

specified by MARUTI. never use

different sizes or types of tyres on

the front and rear wheels. For

information regarding the specified

tyres, refer to ^"SPECIFICATIONS"

section.

Never use oversized tyres or special

shock absorbers and springs to

raise (jack up) your vehicle.This will

change the handling characteristics.

After driving through water, test the

brakes while driving at a slow speed

to see if they have maintained their

normal effectiveness. If the brakes

are less effective than normal, dry

them by repeatedly applying the

brakes while driving slowly until the

brakes have regained their normal

effectiveness.

75

8-2

DRIVING TIPS AND SAFE DRIVING

60G-74E

DO'S AND DON'TS FOR SAFE

DRIVING

Exercise care in handling your vehicle. Be

conscious of not only your own safety but also

the safety of others on the road, and thus enjoy

the best and most comfortable driving

experience.

This section contains basic rules for safe

driving. Read it carefully for good

understanding of the content so that you can

enjoy safe and pleasant driving in your Maruti

vehicle.

72F-08-001

Starting

1. Adjust the driver's seat for the proper

driving posture.

2. Adjust the rear view mirror so as to obtain

the best possible rear view.

3. Before moving off, look forward and back

to confirm safety.
72F-08-002

72F-08-003

8-3
76

60G-74E
INSPECTION AND MAINTENANCE

Interval: This Interval should be judged

by odometer reading or months,

whichever comes first.
km (x 1,000)

months

ROAD TEST

1. Operation of Brakes, Gear shifting & speedometer

2. Body and Chassis noise

AIR CONDITIONER (if equipped)

1. Check belt tension

2. Check Receiver Drier bubbles.

3. Tighten compressor mounting bolts

4. Check all hose joints, tighten if necessary

5. Check functioning of Recirc flap .*

6. Clean condenser with low pressure water

7. Check belt for frayed edges, change if necessary

8. Check all mounting bolts
FREE

1

1

I

I

I

I

—

I

I

_

-

-
INSPECTIONS

5

6

I

I

I

I

T

I

I

C

I

I
10

12

I

I

I

I

T

I

I

C

I

I
PERIODIC

20

24

I

I

I

I

T

I

I

C

I

I
30

36

I

I

I

I

T

I

I

C

I

I
MAINTENANCE

40

48

I

I

I

I

T

I

I

C

I

I
50

60

I

I

I

I

T

I

I

C

I

I
SERVICE

60

72

I

I

I

I

T

I

I

C

I

I
AT,

70

84

I

I

I

I

T

I

I

C

I

I
COST

80

96

I

I

I

I

T

I

I

C

I

I

The rear shock absorbers are filled with

high pressure gas. Never attempt to

disassemble it or throw it into a fire.

Avoid storing it near a heater or heating

device. When scrapping the absorber,

the gas must be released from the

absorber safely. Ask your dealer for

assistance.

89

9-6

INSPECTION AND MAINTENANCE
60G-74E

All maintenance should be carried

out with the Ignition switch in the

"OFF" position and the car parked

securely on the level ground unless

otherwise specified.

If you are In any way unsure of your

ability to undertake a task, then do

not start it but contact your Maruti

dealer to perform the work for you.
ENGINE OIL AND FILTER

Specified oil

Be sure that the engine oil you use comes

under the API classification of SF, SG or SH.

Select the appropriate oil viscosity according

to the above chart.

9-7
90
70F-07-004E

EMERGENCY SERVICE

60G-74E

CAUTION

Vehicle equipped with electronic fuel

injection system will not start by

pushing or towing as the fuel pump

will not work in this condition. This

starting method could also result in

permanent damage to the catalytic

converter. Use jump leads to start a

vehicle with a weak or flat battery.

60G-10-004E

When jump starting your vehicle, use the

following procedure:

1) Use only a 12 volt battery to jump start

your vehicle. Position the good 12V battery

close to your vehicle so that the jump leads

will reach both batteries. When using a

battery installed on another vehicle, DO

NOT LET THE VEHICLES TOUCH. Apply

the parking brakes fully on both vehicles.

2) Turn off all vehicle accessories, except

those necessary for safety reasons (for

example, headlights or hazard lights).
3) Make jump lead connections as follows:

a) Connect one end of the first jump lead

to the positive (+) terminal of the flat

battery.

b) Connect the other end to the positive

(+) terminal of the booster battery.

c) Connect one end of the second jump

lead to the negative (-) terminal of the

booster battery.

d) Make the final connection to an

unpainted, heavy metal part of the

engine of the vehicle with the flat

battery.

Never connect the jump lead directly

to the negative (-) terminal of the

discharged battery, or an explosion

may occur.

10-3
4) If the booster battery you are using is fitted

to another vehicle, start the engine of the

vehicle with the booster battery. Run the

engine at moderate speed.

5) Start the engine of the vehicle with the flat

battery.

6) Remove the jump leads in the exact

reverse order in which you connected

them.

118

60G-74E
EMERGENCY SERVICE

TOWING

If you need to have your vehicle towed, contact

a professional service.

CAUTION

To help avoid damage to your vehicle

during towing, proper equipment and

towing procedures must be used.

Manual Transmission

Whenever possible, your vehicle should be

towed from the front with the front wheels lifted.

If the steering and drivetrain are in good

condition, your vehicle may be towed from the

rear with the rear wheels lifted and the front

wheels on the ground. Before towing, make

sure the steering is unlocked and the

transmission is in neutral.
EMERGENCY REMEDIES

If the Starter Does Not Operate:

1) Try turning the ignition switch to the

"START" position with the headlights

turned on to determine the battery

condition. If the headlights go excessively

dim or go off, it usually means that either

the battery is flat or the battery terminal

contact is poor. Recharge the battery or

correct battery terminal contact as

necessary.

2) If the headlights remain bright, check the

fuses. If the reason for failure of the starter

is not obvious, there may be a major

electrical problem. Have the vehicle

inspected by your authorized MARUTI

dealer.

If the Engine is Flooded

If the engine is flooded with petrol, it may be

hard to start. If this happens, press the

accelerator pedal all the way to the floor and

hold it there while cranking the engine. (Do

not operate the starter motor for more than

15 seconds). Release the accelerator as soon

as the engine has started.
If the Engine Overheats

The engine could overheat temporarily under

severe driving conditions. If the engine coolant

temperature gauge indicates overheating

during driving:

1) Turn off the air conditioner, if equipped.

2) Take the vehicle to a safe place and park.

3) Let the engine run at normal idle speed

for a few minutes until the indicator is within

the normal, acceptable temperature range

between "H" and "C".

If you see or hear escaping steam, stop

the vehicle in a safe place and

Immediately turn off the engine to let it

cool. Do not open the bonnet when

steam is present. When the steam can

no longer be seen or heard, open the

hood to see if the coolant is still boiling.

If it is, you must wait until it stops

boiling before you proceed.

119

10-4

EMERGENCY SERVICE

60G-74E

WARNING TRIANGLE (TYPE-1)

If the temperature indication does not come

down to within the normal, acceptable range:

1) Turn off the engine and check that the

water pump belt and pulleys are not

damaged or slipping. If any abnormality is

found, correct it.

2) Check the coolant level in the reservoir. If

it is found to be lower than the "LOW" line,

look for leaks at the radiator, water pump,

and radiator and heater hoses. If you

locate any leaks that may have caused the

overheating, do not run the engine until

these problems have been corrected.

3) If you do not find a leak, carefully add

coolant to the reservoir and then the

radiator, if necessary. (Refer to "ENGINE

COOLANr in the "INSPECTION AND

MAINTENANCE" section.)
K is dangerous to remove the radiator

cap when the water temperature is

high, because scalding fluid and steam

may be blown out under pressure. The

cap should only be taken off when the

coolant temperature has lowered.

To help prevent personal Injury, keep

hands, tools and clothing away from the

engine cooling fan and airconditioner

fan (if equipped). These electric fans

can automatically turn on without

warning.
843-10-004

In case of vehicle break-down or during

emergency stopping where your vehicle could

become a potential traffic hazard, please keep

the warning triangle, provided with your

vehicle, on the pathway (road) behind the

vehicle so as to warn the approaching traffic,

at an approximate distance of 5-15 m, such

that reflecting side of the triangle faces the

rear. Please activate the hazard warning lamps

before alighting the vehicle to keep the warning

triangle.

10-5
120

60G-74E
EMERGENCY SERVICE

WARNING TRIANGLE (TYPE-2)

In case of vehicle breakdown or during

emergency stopping where your vehicle

could become a potential traffic hazard,

keep the warning triangle, provided with

your vehicle, on the road free from any

obstacles behind your vehicle so as to warn

the approaching traffic, at an approximate

distance of 50-100 m, the reflecting side of

the triangle should face the on coming

traffic. Please activate the hazard warning

lamps before alighting the vehicle to keep

the warning triangle.
Remove the warning triangle

carefully from the box as shown by arrow

1.

Open both the reflector arms as shown

by arrows and lock arms with each other

with the clip provided in the right arm.

Open the bottom stand in counter clock-

wise direction as shown by arrow 3.

Position the warning triangle behind the

vehicle on a plain surface.

Reverse the removal procedure

keeping inside the box.
for

121

10-6