ignition SUZUKI BALENO 1999 1.G Owners Manual (65 Pages)

60G-74E

MODIFICATION WARNING

60G-00-004

The circle with a slash in this manual

means "Don't do this" or "Don't let this

happen".
Do not modify this vehicle. Modification

could adversely affect safety, handling,

performance, or durability and may

contravene regulations. In addition,

damage or performance problems

resulting from modification may not be

covered under warranty.
Improper installation of mobile

communication equipment such as

cellular talephones or CB (Citizen's

Band) radios may cause electronic

interference with your vehicle's ignition

system, resulting in vehicle

performance problems. Consult your

MARUTI dealer or qualified service

technician for advice on installing such

mobile communication equipment.

0-2
Copying, quoting or reproduction of any

part of this manual is not permitted without

explicit approval by MARUTI UDYOG

LIMITED.

60G-74E

WARRANTY POLICY

WARRANTY POLICY

Maruti Udyog Limited (hereinafter called "Maruti"), warrants that each

new Maruti vehicle distributed in India by Maruti and sold by an

authorised Maruti dealer will be free, under normal use and service,

from any defects in material and workmanship at the time of

manufacture SUBJECT TO THE FOLLOWING TERMS AND

CONDITIONS:

(1) Qualification:

To qualify for this warranty:

(a) The Maruti vehicle must be delivered by Maruti authorised

dealer and set-up, serviced by Maruti authorised dealer/

service station.

(b) The warranty registration card in respect of each vehicle

must be completed by the dealer at the time of delivery

of the vehicle and dealer should retain the same.

(2) Term:

The term of the warranty shall be twenty four (24) months

or 40,000 kilometers (whichever occurs first) from the date

of delivery to the first owner.

(3) Maruti's Warranty Obligation:

If any defect(s) should be found in a Maruti vehicle within the

term stipulated above, Maruti's only obligation is to repair or

replace at its sole discretion any part shown to be defective,

with a new part or the equivalent at no cost to the owner for

parts or labour, when Maruti acknowledges that such a defect

is attributable to faulty material or workmanship at the time of

manufacture. The owner is responsible of any repair or

replacements which are not covered by this warranty.
(4) Limitation:

This warranty shall not apply to:

(a) normal maintenance service required other than the three

free services, including without limitation, oil and fluid

changes, headlight aiming, fastener retightening, wheel

balancing, wheelalignment and tyre rotation, cleaning of

injectors, adjustments of carburettor, ignition timing, clutch

and valve clearance.

(b) the replacement of normal wear parts including without

limitation, bulbs, battery, tyres and tubes, spark plugs, belts,

hoses, filters, wiper blades, brushes, contact points, fuses,

clutch disc, brake shoes, brake pads, cable and all rubber

parts (except oil seal and glass run).

(c) any vehicle which has been used for competition or racing.

(d) any repairs or replacement required as a result of accidents

or collision.

(e) any defects caused by misuse, negligence, abnormal use or

insufficient care.

(f) any vehicle which has been modified or altered, including

without limitation, the installation of performance accessories.

(g) any vehicle on which parts or accessories not approved by

Maruti have been used.

(h) any vehicle which has not been operated in accordance with

the operating instructions in the Maruti Owner's Manual,

(i) any vehicle which has not received, during the warranty

term, the service inspections prescribed in the Maruti

Owner's Manual.

G) any vehicle which has been assembled, disassembled,

adjusted or repaired by other than an Maruti authorised

2-1

EMISSION WARRANTY 60G74E

6. Any consequential repairs or replacement of parts which may be found necessary to establish compliance of Emission Warranty,

will not be considered under warranty, unless the same is under product warranty. The consumable will be charged as per

actual under such repair or replacement.

7. Maruti will not be responsible for the cost of transportation of the vehicle to the nearest Maruti dealer workshop or any loss

due to non-availability of the vehicle during the period of lodging of a warranty claim and examination and/or repair by Maruti

dealer.

8. Maruti will not be responsible for any penalty that may be charged by statutory authorities on account of failure to comply with

the EMISSION STANDARDS.

9. Emission Warranty will not be affected on the change of owner, provided all the documents are available.

10. All maintenance actions (as specified in the Owner's manual and Service Booklet) need to be followed and recorded in the

manual for emission warranty.

11. The customer needs to produce the PUC (Pollution Under Control) certificate valid for the period preceeding the test during

which the failure is discovered. The receipts (for the maintenance of the vehicle as per specification in Owner's Manual and

Service Booklet from the date of original purchase of the vehicle) will also be required.

Conditions under which the Emission Warranty is not APPLICABLE

1. In the absence of valid PUC certificate.

2. Vehicle not serviced from Maruti authorised workshop as per the schedule specified in the Owner's Manual .

3. Vehicle subjected to abnormal use (accident, motor race, rallies or for the purpose of establishing the records etc.)

4. Use of non MGP (Maruti Genuine Part).

5. Vehicle tempered in an unauthorised manner.

6. Tampering with odometer so that the actual kilometer reading can not be read.

7. Use of adulterated fuel and/or unspecified oils (Engine oil, Transmission oil and Brake oil etc.)

10

60G-74E

EMISSION WARRANTY

Annexure-A

List of parts covered under Emission Warranty

1. Fuel Injection Assembly, Pressure Regulator, Throttle Body Assembly.

2. Electronic Control Module (ECM).

3. Intake Manifold.

4. EGR Valve.

5. Distributor and internal parts.

6. Ignition coil.

7. Canister Assembly.

8. Vapour Liquid Separator.

9. Fuel Tank and Filler Cap.

10. PCV (Positive Crankcase Ventilation) Valve.

11. Oil Filler Cap.

12. Catalytic Convenor.

13. Exhaust Manifold.

14. All fuel Injection System related SENSORS.

11

60G-74E

BEFORE DRIVING

REMOTE KEYLESS ENTRY SYSTEM

Other Controls (if equipped)
KEYS

60G-50-001E

Remote keyless entry system is installed in

your vehicle. The general features of keyless

entry system are;

1. Remote lock/arming and remote unlock/

disarming.

2. Doors/trunk/bonnet protection.

3. Doors/trunk/bonnet open signal.

4. Personal protection alarm.

5. Mute lock/unlock.

6. Starter immobiliser.

7. Permanent siren chirp enable/disable

(programmable mode).

8. Two stage shock/impact sensor

(programmable mode).

9. Emergency disarm by personalised

PINCODE (programmable mode).

10. Car locator

11. Flashing LE.D.

15
Initially the system is programmed in factory

default. The features operative in factory

default are;

1. Remote lock/arming and remote unlock/

disarming.

2. Doors/trunk/bonnet protection.

3. Doors/trunk/bonnet open signal while

locking/arming.

4. Personal protection alarm.

5. Starter immobiliser.

6. Mute lock/unlock.

7. Permanent siren chirp enable/disable.

8. Emerging disarm by personalised

PINCODE.

9. Car locator.

10. Flashing LE.D.

The system can always be programmed back

to factory default for restoration of original

setting of the system.

For more detail and warranty condition, please

refer to the Owner's Manual of "Maruti Mobile

Security".
70F-01-003

Your vehicle comes with a pair of identical keys.

Keep the spare key in a safe place.

One key can open all of the locks on the vehicle.

The key identification number is stamped on a

metal tag provided with the keys. Keep

the tag in a safe place. If you lose your

keys, you will need this number to have

new keys made. Write the number down

and keep it in a safe accessible place away from

the vehicle.

NOTE:

Keep the spare key very carefully. When it

is lost, consult your dealer by quoting key number.

3-2

BEFORE DRIVING
60G-74E

DOOR LOCKS

60G-03-003

Ignition Key Reminder (if equipped)

A buzzer sounds intermittently to remind you

to remove the ignition key if it is in the ignition

switch when the driver's door is opened.
72F-03-002E

To lock a front door from outside the

vehicle:

a) Insert the key fully and turn the top of

the key toward the front of the vehicle,

or

b) Push in the lock knob down and hold

the door handle up as you close the

door.

To unlock a front door from outside the

vehicle, insert the key fully and turn the top

of the key toward the rear of the vehicle.

To lock a rear door from outside the vehicle,

push in the lock knob down and close the

door.
60G-03-004E

To lock a door from inside the vehicle, push

the lock knob down. Pull the lock knob up to

unlock the door.

3-3
16
Always lock all doors when driving.

Locking the door prevents occupants

from being thrown from the vehicle in

the event of an accident. It also helps

prevent unintentional opening of the

doors.

60G-74E
BEFORE DRIVING

WINDOWS

60G-03-009E

Electric window controls (if equipped)

The driver's door has switches ®,®,© & ©

to operate the driver's window, front

passenger's window, rear right and rear left

passenger's window respectively.

The passenger's door only has a switch ©

to operate the passenger's window. The

electric windows can only be operated when

the ignition switch is in the "ON" position.

To open a window with the driver's door

switches, push the top part of the switch and

to close the window lift up the top part

of the switch.
6OG-O3-010E

The driver's window has an "auto-down"

feature for added convenience (at toll booths

or drive-through restaurants, for example).

This means you can open the window without

holding the window switch in the "Down"

position. Press the driver's window

switch completely down and release it. To

stop the window before it reaches the

bottom, lift up the switch briefly.
To open or to close a window with the

passenger's door switch, push down or push

up the switch.

19

3-6

BEFORE DRIVING

60G-74E

60G-03-011E

The driver's door also has a lock switch for

the passenger's window. When you push in

the lock side of the switch, the passenger's

windows can not be raised or lowered by

operating either of the switches ®,@,® & ©.

To restore normal operation, push the unlock

side of the switch.
60G-03-012

You should always push the lock side

of the lock switch when there are

children in the vehicle. Children can be

seriously injured if they get part of their

body caught by the window during

operation.
NOTE:

The rear side door windows are not designed

to open fully. They can be opened about 2/3

of the way down.

3-7
20
CAUTION

Since the electric windows consumes

a large amount of electricity, the same

should not be used excessively with

engine in "OFF" condition.

60G-74E

BEFORE DRIVING

MIRRORS

60G-03-013

Day-Night Rearview Mirror (if equipped)

To adjust the interior rearview mirror, set the

selector tab to the day position, then move

the mirror up, down, or sideways to obtain the

best view.

When driving at night, you can move the

selector tab to the night position to reduce

glare from the headlights of vehicles behind

you.
Always adjust the mirror with the

selector set to the day position.

Only use the night position if it is

necessary to reduce glare from the

headlights of vehicles behind you. Be

aware that in this position you may

not be able to see some objects that

could be seen in the day position.
Outside Rearview Mirrors

Adjust the outside rearview mirrors so you can

just see the side of your vehicle in the mirrors.

A WARNING

Be careful when judging the size or

distance of a vehicle or other object

seen in the side convex mirror (if

equipped). Be aware that objects look

smaller and appear farther away than

when seen in a flat mirror.

21

3-8

BEFORE DRIVING
6OG-74E

FRONT SEAT ADJUSTMENT

60G-03-014

Electric Mirrors (If equipped)

The switch to control the electric mirrors is

located on the instrument panel.You can only

adjust the mirrors when the ignition switch is

in the "ON" position. To adjust the mirrors:

1) Move the selector switch to the left or right

to select the mirror you wish to adjust.

2) Press the outer part of the switch that

corresponds to the direction in which you

wish to move the mirror.

3) Return the selector switch to the centre

position to help prevent unintended

adjustment.
72F-03-016

Never attempt to adjust the driver's seat

or seatback while driving. The seat or

seatback could move unexpectedly,

causing loss of control. Make sure that

the driver's seat and seatback are

properly adjusted before you start

driving.
72F-03-013

Adjusting Seat Position

The adjustment lever for each front seat is

located under the front of the seat, on the

inboard side. To adjust the seat position, pull

up on the adjustment lever and slide the seat

forward or rearward. After adjustment, try to

move the seat forward and rearward to ensure

that it is securely latched.

3-9
22

60G-74E

STEERING COLUMN CONTROLS

STEERING COLUMN CONTROLS

ignition Switch 4.1

Lighting/Tum Signal Control Lever 4-2

Windscreen Wiper and Washer Lever 4-4

Horn 4.5

Rear Wiper and Washer(lf equipped) 4-5

31

STEERING COLUMN CONTROLS
60G-74E

IGNITION SWITCH

60G-04-001E
70F-02-002

To avoid possible injury, do not operate

controls by reaching through the

steering wheel.
The ignition switch has the following four

positions:

Do not use any locally made key.

Should you require duplicate key,

place your order with MARUTI dealer

only.
60G-04-002E

LOCK

This is the normal parking position. It is the

only position in which the key can be removed.

You must push in the key to turn it to the

"LOCK" position. The "LOCK" position locks

the ignition, and prevents normal use of the

steering wheel after the key is removed.

To release the steering lock, fully insert the

key and turn it clockwise to one of the other

positions. If you have trouble turning the key

to unlock the steering, try turning the steering

wheel slightly to the right or left while turning

the key.

4-1
32

6OG-74E
STEERING COLUMN CONTROLS

ACC

Accessories such as the radio can operate,

but the engine is off.

ON

This is the normal operating position. All

electrical systems are on.

START

This is the position for starting the engine using

the starter motor. The key should be released

from this position as soon as the engine starts.

Never remove the ignition key while

the vehicle is moving. The steering

wheel will lock and you will not be

able to steer the vehicle.

Do not leave children alone In a

parked vehicle. Unattended children

could cause accidental movement of

the vehicle, which could result in

severe personal Injury.

Always remove the key when parked

to prevent unintentional operation of

the vehicle and to improve security.
LIGHTING/TURN SIGNAL

CONTROL LEVER

CAUTION

Do not use the starter motor for

more than 15 seconds at a time. If

the engine does not start; wait 15

seconds before trying again. If the

engine does not start after several

attempts, check the fuel and ignition

systems or consult your MARUTI

dealer.

Do not leave the ignition switch in

the "ON" position if the engine is not

running as the battery will

discharge.
60G-04-003

This control lever is located on the outboard

side of the steering column. Operate the lever

as described below.

Lighting Operation

To turn the lights on or off, twist the knob on

the end of the lever. There are three positions:

in the "OFF" position all lights are off; in the

middle position the front parking lights, tail-

lights, registration plate light, and instrument

lights are on, but the headlights are off; in the

third position the headlights come on in

addition to the other lights.

33

4-2

STEERING COLUMN CONTROLS
60G-74E

With the headlights on, push the lever forward

to switch to the high beams (main beams) or

pull the lever toward you to switch to the low

beams. When the high beams (main beams)

are on, a light on the instrument panel will

come on. To flash the high beams (main

beams) pull the lever slightly towards you and

release it.

Lights "On" Reminder (if Equipped)

A buzzer/chime sounds to remind you to turn

off the lights if they are left on when the ignition

key is removed and the driver's door is opened.
Turn Signal Operation

With the ignition switch in the "ON" position,

move the lever up or down to activate the left

or right turn signals.

Normal Turn Signal

Move the lever clockwise until it clicks to signal

a right turn or anticlockwise to signal a left

turn. When the turn is completed, the signal

will cancel and the lever will return to its normal

position.
6OG-04-006

Lane Change Signal

Some times, such as when changing lanes,

the steering wheel is not turned far enough

to cancel the turn signal. For convenience,

you can flash the turn signal by moving the

lever part way and holding it there. The

lever will return to its normal position when

you release it.

4-3
34
60G-04-006

60G-04-005

60G-04-004E

60G-74E

STEERING COLUMN CONTROLS

WINDSCREEN WIPER AND

WASHER LEVER

60G-04-007E

Windscreen Wipers

To turn the windscreen wipers on, move the

lever down to one of the three operating

positions. In the "INT position (if equipped),

the wipers operate intermittently. The "INT'

position is very convenient for driving in mist

or light rain. In the "LO" position, the wipers

operate at a steady low speed. In the "HI"

position, the wipers operate at a steady high

speed. To turn off the wipers, move the lever

back to the "OFF position.
60G-04-008E

If the lever is equipped with "INT TIME" control,

turn the control toward the "SLOW" or "FAST'

positions to adjust the intermittent wiper

operation to the desired interval.

60G-04-011E

The operation of windscreen wiper and washer

Type-2 is same as Type-1.
60G-04-009E

Windscreen Washer

To spray windscreen washer fluid, pull the

lever toward you. The windscreen wipers will

automatically turn on at low speed if

they are not already on and the "INT" position

is equipped.

To prevent windscreen icing in cold

weather, turn on the defroster to heat

the windscreen before and during

windscreen washer use.

Do not use radiator antifreeze in the

windscreen washer reservoir. It can

severely impair visibility when

sprayed on the windscreen, and can

also damage your vehicle's paint.

35

4-4

STEERING COLUMN CONTROLS
60G-74E

CAUTION

To help prevent damage to the

windscreen wiper and washer system

components, you should take the

following precautions:

• Do not continue to hold in the lever

when there is no windscreen washer

fluid being sprayed or the washer

motor can be damaged.

• Do not attempt to remove dirt from

a dry windscreen with the wipers or

you can damage the windscreen and

the wiper blades. Always wet the

windscreen with washer fluid before

operating the wipers.

• Clear ice or packed snow from the

wiper blades before using the

wipers.

• Check the washer fluid level

regularly. Check it often when the

weather is bad.

• Only fill the washer fluid reservoir

3/4 full during cold weather to allow

room for expansion if the

temperature falls low enough to

freeze the solution.
HORN
REAR WIPER AND WASHER

(if equipped)

60G-04-010

Press the horn button of the steering wheel to

sound the horn. The horn will sound with the

ignition switch in any position.
Press the button located at the end of the

windscreen wiper and washer lever to operate

the rear washer and turn the lever anti

clockwise to operate the rear washer.

4-5
36

60G-74E
INSTRUMENT PANEL

INSTRUMENT PANEL

Instrument Panel 5-1

Instrument Cluster 5-2

Warning and Indicator Lights 5-3

Speedometer/Odometer/Tripmeter (if equipped) 5-5

Tachometer (if equipped) 5-6

Fuel Gauge 5-6

Temperature Gauge 5-6

Hazard Warning Switch 5-7

Rear Window Defroster Switch (if equipped) 5-7

Cigarette Lighter (if equipped) 5-7

Ashtray 5-8

Glove Box 5-8

Heating System (if equipped) 5-9

System Operating Instructions 5-10

Air Conditioning System (if equipped) 5-13

System Operating Instructions 5-13

37

INSTRUMENT PANEL
60G-74E

INSTRUMENT PANEL

1. Instrument cluster

2. Ignition switch

3. Lighting switch/Turn signal and

dimmer switch

4. Windscreen wiper and washer

switch

5. Hazard warning switch

6. Rear window defroster switch

(if equipped)

7. Other switches (if equipped)

8. Heater control panel

9. Audio system (if equipped)

10. Cigarette lighter (if equipped)

11. Ashtray

12. Bonnet release

13. Center ventilator

14. Side ventilator

15. Side defroster

16. Glove box

17. Fuse box

18. Cup holder (if equipped)

5-1
38

ignition SUZUKI BALENO 1999 1.G Owners Manual

Page 2 of 65

Page 3 of 65

Page 5 of 65

Page 7 of 65

Page 9 of 65

Page 10 of 65

Page 15 of 65

Page 16 of 65

Page 17 of 65

Page 18 of 65

SUZUKI Manuals