ignition SUZUKI BALENO 1999 1.G User Guide

60G-74E
INSTRUMENT PANEL

INSTRUMENT CLUSTER

© Speedometer

® Odometer

© Trip meter (if equipped)

© Trip meter reset knob

© Tachometer (if equipped)

© Fuel gauge

® Temperature gauge

© Warning and indicator lights

60G-05-002

39

5-2

INSTRUMENT PANEL
60G-74E

WARNING AND INDICATOR LIGHTS

70F-07-070

Brake fluid level warning/Parking Brake

Indicator light

This light operates under three conditions:

1) when the ignition switch is turned to the

"START' position, 2) when the fluid in the brake

fluid reservoir falls below the specified level

or 3) when the parking brake is not fully

released and the ignition switch is in the "ON"

position. The light should go out after starting

the engine and fully releasing the parking

brake, if the fluid in the brake fluid reservoir is

adequate. If the light does not go off or comes

on whilst you are driving, it may mean that

there is something wrong with the vehicle's

braking system. If this happens, you should:

1) Pull off the road and stop carefully.

Remember that stopping distance may

be longer, you may have to push

harder on the pedal, and the pedal

may go down farther than normal.
2) Test the brakes by carefully starting and

stopping at the side of the road.

3) If you determine that it is safe, drive

carefully at low speed to the nearest dealer

for repairs.

Have the vehicle towed to the nearest

dealer for repairs.
or

4)

If any of the following conditions occur,

you should Immediately ask your

MARUTI dealer to inspect the brake

system.

• If the brake fluid level warning light

does not go out after the engine has

been started and the parking brake

has been fully released.

• If the brake fluid level warning light

does not come on when the ignition

switch is turned to the "START"

position.

• If the brake fluid level warning light

comes on at any time during vehicle

operation.

NOTE:

Because the disc brake system is self

adjusting, the fluid level will drop as the brake

pads become worn.

Replenishing the brake fluid reservoir is

considered normal periodic maintenance.
70F-03-039

Oil Pressure Light

This light comes on when the ignition switch

is turned on, and goes out when the engine

is started. The light will come on and remain

on if there is insufficient oil pressure. If the

light comes on when driving, pull off the

road as soon as you can and stop the

engine. Check the oil level and add oil if

necessary (see pages 9-8 and 9-9). If there

is enough oil, the lubrication system should

be inspected by your MARUTI dealer before

you drive the vehicle again.

5-3
40

60G-74E
INSTRUMENT PANEL

60G-09-002

CAUTION

If you operate the engine with this

light on, severe engine damage can

result.

Do not rely on the Oil Pressure Light

to indicate the need to add oil. Be

sure to periodically check the engine

oil level (see pages 9-8 and 9-9).
70F-03-009

Charging Light

This light comes on when the ignition switch

is turned on, and goes out when the engine is

started. The light will come on and remain on

if there is something wrong with the battery

charging system. If the light comes on when

the engine is running, the charging system

should be inspected immediately by your

MARUTI dealer.

CAUTION

Do not continue driving long with the

charging light ON as this will drain the

battery 'dead'.
72F-05-027

"Malfunction Indicator" Light

Your vehicle has a computer-controlled

emission control system. A "Malfunction

Indicator" light is provided on the instrument

panel to indicate when it is necessary to have

the emission control system serviced. The

"Malfunction Indicator" light comes on when

the ignition switch is turned to "ON" and goes

out when the engine is started.

If the "Malfunction Indicator" light comes on

when the engine is running, there is a problem

with the emission control system. Take the

vehicle to your MARUTI dealer to have the

problem corrected.

CAUTION

Continuing to drive the vehicle when

the "Malfunction Indicator" light is on

can cause permanent damage to the

vehicle's emission control system, and

can affect fuel economy and

driveability.

5-4

INSTRUMENT PANEL
60G-74E

70F-03-042

Turn Signal Indicators

When you turn on the left or right turn signals,

the corresponding green arrow on the

instrument panel will flash along with the

respective turn signal lights. When you turn

on the hazard warning switch, both arrows will

flash along with all of the turn signal lights.

70F-03-043

Main Beam (High Beam) Indicator Light

This indicator comes on when headlight main

beams (high beams) are turned on.
SPEEDOMETER/ODOMETER/

TRIPMETER (if equipped)

60G-05-003

© Speedometer

© Odometer

(D Trip meter

© Trip meter reset knob

The speedometer indicates vehicle speed in

km/h.The odometer records the total distance

the vehicle has been driven. The tripmeter can

be used to measure the distance travelled on

short trips or between fuel stops. You can reset

the tripmeter to zero by pushing the reset

knob.
CAUTION

Keep track of your odometer reading

and check the maintenance schedule

regularly for required services.

Increased wear or damage to certain

parts can result from failure to perform

required services at the proper mileage

intervals and your warranty rights may

be affected.

5-5

42
41

60G-74E
INSTRUMENT PANEL

TACHOMETER (if equipped)

FUEL GAUGE
TEMPERATURE GAUGE

60G-05-004

The tachometer indicates engine speed in

revolutions per minute.

Never drive with the engine speed

indicator in the red zone or severe

engine damage can result.
60G-05-005

This gauge gives an approximate indication

of the amount of fuel in the fuel tank as shown

in figure. "P stands for full and "E" stands for

empty.

If the indicator gets in the red zone, refill the

tank as soon as possible.

Note:

This vehicle has fuel gauge of new design.

Even when the ignition switch is "OFF", the

needle will not return to "E" position but will

show the reading.
60G-05-006

When the ignition switch is on, this gauge

indicates the engine coolant temperature.

Under normal driving conditions, the indicator

should stay within the normal, acceptable

temperature range between "H" and "C". If the

indicator approaches "H", and maintains that

reading, overheating is indicated. Follow the

instructions for engine overheating in the

EMERGENCY REMEDIES section.

CAUTION

Continuing to drive the vehicle when

engine overheating is indicated, can

result in severe engine damage.

43

5-6

INSTRUMENT PANEL

60G-74E

HAZARD WARNING SWITCH
REAR WINDOW DEFROSTER SWITCH CIGARETTE LIGHTER (if equipped)

(if equipped)

60G-05-007

Push in the hazard warning switch to activate

the hazard warning lights. All four turn signal

lights and both turn signal indicators will flash

simultaneously. To turn off the lights, push the

switch again.

Use the hazard warning lights to warn other

traffic during emergency parking or when your

vehicle could otherwise become a traffic

hazard.
60G-05-008

When the rear window is misted, push this

switch to clear the window. An indicator light

will be lit when the defroster is on. The

defroster will only work when the ignition

switch is in the "ON position. To turn off the

defroster, push the switch again.

CAUTION

The rear window defroster uses a large

amount of electricity. Be sure to turn

off after the window has become clear.
60G-05-009

To use the cigarette lighter, push it all the way

into the receptacle and release it. It will

automatically heat up and will pop out to its

normal position when it is ready for use.

5-7
44

S0G-74E
OPERATING YOUR VEHICLE

OPERATING YOUR VEHICLE

Exhaust Gas Warning 7-1

Daily Inspection Checklist 7-1

Starting the Engine 7-2

Using the Transmission 7-3

Braking 7-4

Running-in 7-5

Catalytic Converter (if equipped) 7-6

Improving Fuel Economy 7-7

Trailer Towing 7-7

OPERATING YOUR VECHILE

60G-74E

EXHAUST GAS WARNING
DAILY INSPECTION CHECKLIST

60G-07-001E

Avoid breathing exhaust gases.

Exhaust gases contain carbon

monoxide, a potentially lethal gas that

is colourless and odourless. Since

carbon monoxide is difficult to detect

by itself, be sure to take the following

precautions to help prevent carbon

monoxide from entering your vehicle.

• Do not leave the engine running in

garages or other confined areas.

• Do not park with the engine running

for a long period of time, even in an

open area. If it is necessary to sit for

a short time in a parked vehicle <=>
with the engine running, make sure

the air intake lever is set to "FRESH

AIR" and the fan is at high speed.

To allow proper operation of your

vehicle's ventilation system, keep

the air inlet grille in front of the

windscreen clear of snow, leaves, or

other obstructions at all times.

Keep the exhaust tailpipe area clear

of snow and other material to help

reduce the buildup of exhaust gases

under the vehicle.This is particularly

important when parked in blizzard

conditions.

Have the exhaust system inspected

periodically for damage and leaks.

Any damage or leaks should be

repaired immediately.

7-1
70F-05-007

Before driving:

1) Make sure that windows, mirrors, lights,

and reflectors are clean and unobstructed.

2) Check the tyres.

3) Look for fluid and oil leaks.

NOTE:

It is normal for water to drip from the air

conditioning system after use.

4) Adjust the seat/head restraint.

5) Check the brake pedal and the parking

brake lever.

6) Adjust the mirrors.

7) Make sure that you and passengers have

properly fastened your seat belts.

8) Make sure that all warning lights come on

as the key is turned to the "ON" or "START'

position.

9) Check all gauges.

10) Make sure that the brake fluid level

warning light is off when the parking brake

is released with the ignition switch in "ON"

position.

66
65

60G-74E
OPERATING YOUR VEHICLE

Once a week, or each time you fill your fuel

tank, perform the following under-bonnet

checks:

1) Engine oil level.

2) Coolant level.

3) Brake fluid level.

4) Power steering (if equipped) fluid level.

5) Windscreen washer fluid level.

6) Battery solution level.

7) Bonnet latch operation.

Pull the bonnet release handle inside the

vehicle. Make sure that you can not open

the hood all the way without releasing the

secondary latch. Be sure to close the hood

securely after checking for proper

operation. See "All Latches, Hinges &

Locks" of "PERIODIC MAINTENANCE

SCHEDULE" in the "INSPECTION AND

MAINTENANCE" section for lubrication

schedule.

Make sure the bonnet is fully closed

and latched before driving. If it is not,

it can fly up unexpectedly during

driving, obstructing your view and

resulting in an accident.
STARTING THE ENGINE

Before starting the engine:

1) Make sure the parking brake is applied

fully.

2) Manual Transmission - Shift into "N"

(neutral) and depress the clutch pedal all

the way to the floor. Hold it while starting

the engine.

Make sure that the parking brake is

applied fully and the transmission is in

Neutral before attempting to start the

engine.

CAUTION

Stop turning the starter immediately

after the engine has started or the

starter system can be damaged.

Do not crank the engine for more

than 15 seconds at a time. If the

engine doesn't start on the first try,

wait about 15 seconds before trying

again.
Starting a Cold Engine

Engine which is started after 6 hours should

be treated as cold engine.

For Electronic fuel injection models

• With your foot off the accelerator pedal,

crank the engine by turning the ignition

key to "START1. Release the key when the

engine starts.

• If the engine does not start after 15

seconds of cranking, wait about 15

seconds, then press down the accelerator

pedal to 1/3 of its travel and try cranking

the engine again. Release the key and

accelerator pedal when the engine starts.

• If the engine still does not start, try holding

the accelerator pedal all the way to the

floor while cranking. This should clear the

engine if it is flooded.

Starting a Warm Engine

For Electronic fuel injection models:

Use the same procedure as for "Starting a cold

Engine".

67

7-2

OPERATING YOUR VECHILE

60G-74E

USING THE TRANSMISSION

70F-04-005E

Starting off

To start off, depress and maintain pressure

upon the clutch pedal and change into 1st

gear. After releasing the parking brake,

gradually release the clutch. When you hear

a change in the engine's sound (speed), gently

apply pressure to the accelerator to keep the

engine sound (speed) constant whilst

continuing to gradually release the clutch.
Gear changing

All forward gears are synchronized, which

provides for quiet, easy changing. Always

depress the clutch pedal fully before changing

gears.The following table shows the maximum

allowable speed for each gear.
GEAR

First

Second

Third

Fourth

Fifth
MAXIMUM SPEED

50 km/h

95 km/h

140 km/h

Top Speed

Top Speed

7-3
68

60G-74E
OPERATING YOUR VEHICLE

CATALYTIC CONVERTER

(if equipped)

70F-05-005

The purpose of the catalytic converter installed

on your vehicle is to convert exhaust pollutants

to harmless water vapour, carbon dioxide, and

nitrogen. Use of leaded fuel in vehicles

equipped with catalytic converters is

prohibited, because lead deactivates the

pollutant-reducing components of the catalyst

system.

It is very important to keep the engine properly

tuned. Engine misfiring, which can result from

an improperly tuned engine, may cause

overheating of the catalyst. This may result in

permanent heat damage to the catalyst and

other vehicle components.
CAUTION

To minimize the possibility of catalyst

or other vehicle damage:

• Maintain the engine in the proper

operating condition.

• In the event of an engine

malfunction, particularly one

involving engine misfire or other

apparent loss of performance, have

the vehicle serviced promptly.

• Do not turn off the engine or

interrupt the ignition when the

transmission is in gear and the

vehicle is in motion.

• Do not try to start the engine by

pushing or towing the vehicle, or

coasting down a hill.

• Do not idle the engine with any spark

plug wires disconnected or

removed, such as during diagnostic

testing.

• Do not idle the vehicle for prolonged

periods if idling seems rough or

there are other malfunctions.

• Do not allow the fuel tank to get near

the empty level.
60Q-07-002E

Be careful where you park and drive;

the catalytic converter and other

exhaust components can get very hot.

As with any vehicle, do not park or

operate this vehicle in areas where

combustible materials such as dry

grass or leaves can come in contact

with a hot exhaust system.

7-6

OPERATING YOUR VECHILE

60G-74E

IMPROVING FUEL ECONOMY

The following instructions will help you improve

fuel economy.

Avoid excessive idling:

If you are to wait for more than a minute while

you are parked, stop the engine and start it

again later. When warming up a cold engine,

allow the engine to idle until the temperature

gauge pointer comes up to the "C" position. In

this position, the engine is sufficiently warm

for starting off.

Avoid "fast" starts:

Fast starts away from lights or stop signs will

consume fuel unnecessarily and shorten

engine life. Start off slowly.

Avoid unnecessary stops:

Avoid unnecessary deceleration and stopping.

Try to maintain a slow, steady speed whenever

possible. Slowing down and then accelerating

again uses more fuel.

Keep a steady cruising speed:

Keep as constant a speed as road and traffic

conditions will permit.
Air Outlet side

(Facing up)

60G-09-010

Keep the air cleaner clean:

A dirty air cleaner will cause the carburation

system to supply too much fuel to the engine

for the amount of air being supplied. The result

is waste of fuel due to incomplete combustion.

Keep weight to a minimum:

The heavier the load, the more fuel the vehicle

consumes. Take out any luggage or cargo

when it is not necessary.

Keep tyre pressures correct:

Under-inflation of the tyres can waste fuel due

to increased running resistance of the tyres.

Keep your tyres inflated to the correct pressure

shown on the label on the driver's side door

or door lock pillar.
TRAILER TOWING

Your MARUTI was originally designed to carry

people and a normal amount of cargo, not to

tow a trailer. Maruti does not recommend you

use your vehicle to tow a trailer.Towing a trailer

can adversely affect handling, durability, and

fuel economy.

7-7

72
71

60G-74E
DRIVING TIPS AND SAFE DRIVING

DRIVING TIPS AND SAFE DRIVING

High Speed Driving 8-1

Driving on Hills 8-1

Driving on Slippery Roads 8-2

Driving on Wet Roads 8-2

Do's and Don'ts for Safe Driving 8-3

73

DRIVING TIPS AND SAFE DRIVING

60G-74E

70F-06-001

Wear Your Seat Belts at All Times.

The driver and passengers should

be property restrained at all times,

using the seatbelts provided. Refer

to the "SEATBELTS" section for

instructions on proper use of the

seatbelts.

Never drive while under the

influence of alcohol or other drugs.

Alcohol and drugs can seriously

impair your ability to drive safely,

greatly increasing the risk of injury

to yourself and others. You should

also avoid driving when you are

tired, sick, irritated, or under stress.
HIGH-SPEED DRIVING

When driving at a high-speed, pay attention to

the following:

• Stopping distance progressively increases

with vehicle speed. Apply the brakes far

enough ahead of the stopping point to

allow for the extra stopping distance.

• On rainy days, "Aquaplaning" can occur.

"Aquaplaning" is the loss of direct contact

between the road surface and the vehicle's

tyres due to a water film forming between

them. Steering or braking the vehicle while

"Aquaplaning" can be very difficult, and

loss of control can occur. Keep speed

down when the road surface is wet.

• At high speeds, the vehicle may be

affected by side winds. Therefore, reduce

speed and be prepared for unexpected

buffeting, which can occur at the exits of

tunnels, when passing by a cut of a hill, or

when being overtaken by large vehicles,

etc.

DRIVING ON HILLS

• When climbing steep hills, the vehicle may

begin to slow down and show a lack of

power. If this happens, you should change

to a lower gear so that the engine will again

be operating in its normal power range.

Change rapidly to prevent the vehicle from

losing momentum.
When driving down a hill, the engine

should be used for braking by shifting to

next lower gear.

Try not to hold the brake pedal down

too long or too often while going down

a steep or long hill. This could cause

the brakes to overheat, resulting in

reduced braking efficiency. Failure to

take this precaution could result in loss

of vehicle control.

CAUTION

When descending a down hill, NEVER

turn the ignition key to the "OFF"

position. Emission control system and

automatic transmission (if equipped)

damage may result.

DRIVING ON SLIPPERY ROADS

Under wet road conditions you should drive

at a lower speed than on dry roads due to

possible slippage of tyres during braking.

When driving on icy, snowcovered, or muddy

roads, reduce your speed and avoid sudden

acceleration, abrupt braking, or sharp steering

movements.

8-1

60G-74E
INSPECTION AND MAINTENANCE

INSPECTION AND MAINTENANCE

Periodic Maintenance Schedule.. 9-2

Engine Oil and Filter 9-7

Gear OH 9-10

Engine Coolant 9-11

Windscreen Washer Fluid 9-13

Air Cleaner 9-13

Spark Plugs 9-14

Brakes 9-15

Steering 9-17

Power Steering (if equipped) 9-18

Clutch Pedal 9-18

Tyres... 9-19

Battery 9-22

Fuses 9-23

Bulb Replacement , 9-25

Wiper Blades 9-29

83

INSPECTION AND MAINTENANCE

60G-74E

70F-05-002

You should take extreme care when

working on your vehicle to prevent

accidental injury. Here are a few

precautions that you should be

especially careful to observe:

• Do not leave the engine running in

garages or other confined areas.

• When the engine Is running, keep

hands, clothing, tools, and other

objects away from the fan and water

pump belt. Even though the fan may

not be moving, it can automatically

turn on without warning. ^
When it is necessary to do service

work with the engine running, make

sure that the parking brake is applied

fully and the transmission is in

Neutral.

Do not touch ignition wires or other

ignition system parts when starting

the engine or when the engine is

running, or you could receive an

electric shock.

Be careful not to touch a hot engine,

exhaust manifold and pipes, muffler,

radiator and water hoses.

Do not allow smoking, sparks, or

flames around gasoline or the

battery. Flammable fumes are

present.

Do not get under your vehicle if it is

supported only with the portable

jack provided in your vehicle.

Be careful not to cause accidental

short circuits between the positive

and negative battery terminals.

Keep used oil, coolant, and other

fluids away from children and pets.

Dispose of used fluids properly;

never pour them on the ground, into

sewers, etc.

9-1
84

60G-74E
INSPECTION AND MAINTENANCE

PERIODIC MAINTENANCE SCHEDULE

The following table shows when regular

maintenance on your vehicle is required. This

table shows in kilometres and months when

inspections, adjustments, lubrication and other

services should be performed.

Maruti recommends that maintenance

on your Maruti vehicle be performed by

Maruti Authorised Dealer/Service

Station.
CAUTION

Whenever it becomes necessary to

replace parts on your vehicle, it is

recommended that you use MARUTI

GENUINE PARTS (MGP).

85

9-2

INSPECTION AND MAINTENANCE

6OG-74E

PERIODIC MAINTENANCE SCHEDULE

A....Ad]ust. l....lnspect and correct or replace If necessary.

T....Tighten to specified torque. C....CIean.

R....Replace or change. O....Rotate

L....Lubrlcate.

Note:

This table includes services as scheduled up to 80,000 km mileage. Beyond 80,000 km, carry out the same services at the same intervals

respectively.

Interval: This interval should be judged

by odometer reading or months,

whichever comes first.
km (x 1,000)

months

ENGINE

1. Water pump drive belt (tension, wear)

2. Engine coolant (level, leakage)

3. Engine oil (API GRADE SF, SG, SH) & Oil filter

4. Cooling system hoses and connections (leakage, damage)

5. Engine bolts (All cylinder head and manifold fixings)

6. Engine mounting (loose, damage)

7. Valve clearance

8. Camshaft timing belt (damage, wear)

9. Exhaust system (noise, leakage or otherwise defective)

10. Positive crankcase ventilation System (Hoses, connections and valve;

IGNITION

1. Ignition wiring, (damage, deterioration)

2. Spark plugs (clean and adjust the gap)
FREE INSPECTIONS

1

1

A

I

R

I

-

-

-

_
5

6

I

I

I

I

-

-

A

-
10

12

I

I

R

I

T

T

-

-
PERIODIC MAINTENANCE SERVICE AT COST

20

24

I

R

R

I

-

-

A

I

Replace every 1,00,000 km

-

-

-
I

I

-

-
-

-

-

I
I

I

I

R
30

36

I

I

R

I

T

T

-

-

-

-

-

I
40

48

I

R

R

I

-

-

A

I

I

I

I

R
SO

60

I

I

R

I

T

T

-

-

-

-

-

I
60

72

R

R

R

I

-

-

A

I

I

I

I

R
70

84

A

I

R

I

T

T

-

-

-

-

-

I
80

96

I

R

R

I

-

-

A

I

I

I

I

R

9-3
86

60G-74E
INSPECTION AND MAINTENANCE

Interval: This Interval should be judged

by odometer reading or months,

whichever comes first.
km (x 1,000)

months

ROAD TEST

1. Operation of Brakes, Gear shifting & speedometer

2. Body and Chassis noise

AIR CONDITIONER (if equipped)

1. Check belt tension

2. Check Receiver Drier bubbles.

3. Tighten compressor mounting bolts

4. Check all hose joints, tighten if necessary

5. Check functioning of Recirc flap .*

6. Clean condenser with low pressure water

7. Check belt for frayed edges, change if necessary

8. Check all mounting bolts
FREE

1

1

I

I

I

I

—

I

I

_

-

-
INSPECTIONS

5

6

I

I

I

I

T

I

I

C

I

I
10

12

I

I

I

I

T

I

I

C

I

I
PERIODIC

20

24

I

I

I

I

T

I

I

C

I

I
30

36

I

I

I

I

T

I

I

C

I

I
MAINTENANCE

40

48

I

I

I

I

T

I

I

C

I

I
50

60

I

I

I

I

T

I

I

C

I

I
SERVICE

60

72

I

I

I

I

T

I

I

C

I

I
AT,

70

84

I

I

I

I

T

I

I

C

I

I
COST

80

96

I

I

I

I

T

I

I

C

I

I

The rear shock absorbers are filled with

high pressure gas. Never attempt to

disassemble it or throw it into a fire.

Avoid storing it near a heater or heating

device. When scrapping the absorber,

the gas must be released from the

absorber safely. Ask your dealer for

assistance.

89

9-6

INSPECTION AND MAINTENANCE
60G-74E

All maintenance should be carried

out with the Ignition switch in the

"OFF" position and the car parked

securely on the level ground unless

otherwise specified.

If you are In any way unsure of your

ability to undertake a task, then do

not start it but contact your Maruti

dealer to perform the work for you.
ENGINE OIL AND FILTER

Specified oil

Be sure that the engine oil you use comes

under the API classification of SF, SG or SH.

Select the appropriate oil viscosity according

to the above chart.

9-7
90
70F-07-004E