brake SUZUKI GRAND VITARA 2000 2.G Service User Guide

YH4
GRAND
VITARA
3
STEERING, SUSPENSION, WHEELS AND TIRES 3-1
GENERAL DIAGNOSIS3-1 . . . . . . . . . . . . . . . . .
Diagnosis Table 3-1. . . . . . . . . . . . . . . . . . . . . .
TIRE DIAGNOSIS3-6 . . . . . . . . . . . . . . . . . . . . . .
Irregular and / or Premature Wear 3-6. . . . . . .
Wear Indicator 3-6. . . . . . . . . . . . . . . . . . . . . . . Radial Tire Waddle 3-6. . . . . . . . . . . . . . . . . . .
Radial Tire Lead 3-8. . . . . . . . . . . . . . . . . . . . . .
VIBRATION DIAGNOSIS3-8 . . . . . . . . . . . . . . .
SECTION 3
STEERING, SUSPENSION, WHEELS AND TIRES
DIAGNOSIS3-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FRONT END ALIGNMENT3A-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
POWER STEERING SYSTEM3B1-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AIR BAG STEERING WHEEL AND COLUMN3C1-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FRONT SUSPENSION3D-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REAR SUSPENSION3E-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WHEELS AND TIRES3F-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CONTENTS
GENERAL DIAGNOSIS
Since the problems in steering, suspension, wheels and tires involve several systems, they must all be considered
when diagnosing a complaint. To avoid using the wrong symptom, always road test the vehicle first.
Proceed with the following preliminary inspections and correct any defects which are found.
1) Inspect tires for proper pressure and uneven wear.
2) Raise vehicle on a hoist and inspect front and rear suspension and steering system for loose or damaged parts.
3) Spin front wheel. Inspect for out-of-round tires, out-of-balance tires, bent rims, loose and / or rough wheel bear-
ings.
DIAGNOSIS TABLE
ConditionPossible CauseCorrection
Vehicle Pulls (Leads)
Mismatched or uneven tires.

Tires not adequately inflated.

Broken or sagging springs.

Radial tire lateral force.

Disturbed front end alignment.

Disturbed rear axle alignment.

Brake dragging in one road wheel.

Loose, bent or broken front or rear
suspension parts.Replace tire.
Adjust tire pressure.
Replace spring.
Replace tire.
Check front end alignment.
Check rear axle alignment.
Repair front brake.
Tighten or replace suspension part.

YH4
GRAND
VITARA
3-4 STEERING, SUSPENSION, WHEELS AND TIRES
ConditionPossible CauseCorrection
Wander or Poor
Steering Stability
Mismatched or uneven tires.

Loose ball joints and tie rod
ends.

Faulty shock absorbers / struts or
mounting.

Loose stabilizer bar.

Broken or sagging springs.

Rack and pinion not properly adjusted.
(if equipped with manual steering
gear case)

Disturbed front end alignment.Replace tire or inflate tires to
proper pressure.
Replace suspension control arm or
tie rod end.
Replace absorber / strut or repair
mounting.
Tighten or replace stabilizer bar or
bushes.
Replace spring.
Check or adjust rack and pinion
torque.
Check and adjust front end alignment.
Erratic Steering when
Braking
Worn wheel bearings.

Broken or sagging springs.

Leaking wheel cylinder or caliper.

Warped discs.

Badly worn brake linings.

Drum is out of round in some brakes.

Wheel tires are inflated unequally.

Defective wheel cylinders.

Disturbed front end alignment.Replace wheel bearing.
Replace spring.
Repair or replace wheel cylinder or
caliper.
Replace brake disc.
Replace brake shoe lining.
Replace brake drum.
Inflate tires to proper pressure.
Replace or repair wheel cylinder.
Check front end alignment.
Low or Uneven Trim
Height
Right-to-left trim height
(H) difference should be
within 15 mm (0.6 in.)
with curb weight.
*Same with rear side.
Broken or sagging springs.

Overloaded.

Incorrect springs.Replace spring.
Check loading.
Replace spring.
Ride Too Soft
Faulty shock absorber or struts.Replace shock absorber or strut.
Suspension Bottoms
Overloaded.

Faulty shocks or struts.

Incorrect broken or sagging springs.Check loading.
Replace shock absorber or strut.
Replace spring.

YH4
GRAND
VITARA
3-8 STEERING, SUSPENSION, WHEELS AND TIRES
RADIAL TIRE LEAD
ªLeadº is the deviation of the vehicle from a straight path on a level
road with no pressure on the steering wheel.
Lead is usually caused by:
1) Incorrect alignment.
2) Uneven brake adjustment.
3) Tire construction.
The way in which a tire is built can produce lead in a vehicle. An ex-
ample of this is placement of the belt. Off center belts on radial tires
can cause the tire to develop a side force while rolling straight down
the road. If one side of the tire is a little larger diameter than the oth-
er, the tire will tend to roll to one side. This will develop a side force
which can produce vehicle lead.
The procedure on previous page should be used to make sure that
front alignment is not mistaken for tire lead.
1) Part of the lead diagnosis procedure is different from the tire
rotation pattern currently in the owner's and service manuals. If
a medium to high mileage tire is moved to the other side of the
vehicle, be sure to check that ride roughness has not developed.
2) Rear tires will not cause lead.
VIBRATION DIAGNOSIS
Wheel unbalance causes most of the highway speed vibration
problems. If a vibration remains after dynamic balancing, it can be
caused by three things.
1) Tire runout.
2) Wheel runout.
3) Tire stiffness variation.
Measuring tire and / or wheel free runout will uncover only part of the
problem. All three causes, known as loaded radial runout, must be
checked by using a Tire Problem Detector (TPD). If a TPD is not
available, the more time consuming method of substituting known
good tire and wheel assemblies on the problem vehicle can be
used.

YH4
GRAND
VITARA
3B1-6 POWER STEERING (P / S) SYSTEM
ConditionPossible CauseCorrection
Vehicle pulls to
one side during
straight driving
Mismatched or uneven tire

Low or uneven tire inflation pressure

Brake dragging in one wheel

Front end alignment out of order

Rear end alignment out of order

Malfunction of control valve in gear boxReplace tire.
Inflate tires to proper pressure or
adjust right & left tires inflation
pressure.
Repair.
Check and adjust front end
alignment.
Check and adjust rear end
alignment.
Replace gear box.
Steering wheel
play is large and
vehicle wanders
Refer to ªDiagnosisº in Section 3.
Fluid leakage
Loose joints of (hydraulic pressure)
pipes and hoses

Deformed or damaged pipes or hosesRetighten.
Replace defective part.
Abnormal noise
Air drawn in due to insufficient amount of fluid

Air mixed into fluid from pipes or hoses

Slipping (loose) P / S belt

Worn P / S belt

Loose gear box fastening bolt

Loose linkage or joints

Pipes or hoses in contact with part of
vehicle body

Vanes of P / S pump defective

Malfunction of control valve in gear box

Bearing of P / S pump shaft defectiveAdd fluid and purge air.
Replace pipes or hoses.
Adjust belt tension.
Replace belt.
Retighten bolts.
Retighten.
Install pipes and hoses correctly.
Replace defective part.
Replace gear box.
Replace bearing.
No idle up
Power steering pressure switch defectiveReplace power steering
pressure switch.

YH4
GRAND
VITARA
3B1-12 POWER STEERING (P / S) SYSTEM
TIE-ROD END BOOT CHECK
Check boot for crack and damage and if any, replace it with a new
one.
AIR BLEEDING PROCEDURE
1) Hoist the front end of vehicle and apply safety stands.
2) Fill P / S fluid reservoir with fluid up to specified level.
NOTE:
Before starting engine, place transmission gear shift lever
in ªNeutralº (shift selector lever to ªPº range for A / T mod-
el), and set parking brake.
3) After running engine at idling speed for 3 to 5 seconds, stop it
and add fluid to satisfy specification.
4) With engine stopped, turn steering wheel to the right and left as
far as it stops, repeat it a few times and fill fluid to specified level.
5) With engine running at idling speed, repeat stop-to-stop turn of
steering wheel till all foams in P / S fluid reservoir are gone.
NOTE:
Make sure to bleed air completely. If air remains in fluid, P / S
pump may make humming noise or steering wheel may feel
heavy.
6) Finally check to make sure that fluid is filled to specified level.

YH4
GRAND
VITARA
3D-6 FRONT SUSPENSION
1. Strut tower bar
1. E-ring
1. Front wheel speed sensor harness clamp bolt
1. Strut bracket bolts
2. Lower arm
3. Jack
1. Strut support nuts
STRUT DAMPER
REMOVAL
1) Remove strut tower bar (if equipped).
2) Hoist vehicle, allowing front suspension to hang free.
3) Remove wheel.
4) Remove E-ring securing brake hose and take brake hose off
strut bracket as shown.
5) If equipped with ABS, remove front wheel speed sensor harness
clamp bolt.
6) Remove strut bracket bolts, then support lower arm with jack.
7) Remove strut support nuts.
Hold strut by hand so that it will not fall off.
8) Remove strut.

YH4
GRAND
VITARA
FRONT SUSPENSION 3D-7
1. E-ring
2. Bracket end surface
INSTALLATION
1) Install strut by reversing removal steps 1) ± 8). Insert bolts in
such a direction as shown.
2) Torque all fasteners to specifications.
Tightening Torque
(a): 55 N
.m (5.5 kg-m, 40.0 lb-ft)
(b): 95 N
.m (9.5 kg-m, 69.0 lb-ft)
(c): 50 N
.m (5.0 kg-m, 36.5 lb-ft)
NOTE:
Brake hose installation.
Don't twist hose when installing it. Install E-ring as far as
bracket end surface as shown.

YH4
GRAND
VITARA
3D-8 FRONT SUSPENSION
1. Circlip
2. Washer
1. Wire
1. Front wheel
speed sensor
2. Harness clamp bolt
COIL SPRING
REMOVAL
1) Hoist vehicle, allowing front suspension to hang free.
2) Remove wheels.
3) Remove axle shaft drive flange (For 4WD vehicle).
4) Remove front drive shaft circlip and washer (For 4WD vehicle).
5) Remove caliper bolts and suspend caliper with a wire hook.
CAUTION:
Hang removed caliper with a wire hook so as to prevent
brake hose from bending and twisting excessively or be-
ing pulled.
Don't operate brake pedal with pads removed.
6) If equipped with ABS, remove harness clamp bolt and remove
front wheel speed sensor from knuckle.
CAUTION:

Do not pull wire harness when removing front wheel
speed sensor.

Do not cause damage to surface of front wheel speed
sensor and do not allow dust, etc. to enter its installa-
tion hole.
7) Remove brake disc.
NOTE:
If brake disc can not be removed by hand, use 8 mm bolts
as shown.

YH4
GRAND
VITARA
3D-12 FRONT SUSPENSION
1. Lock washer
2. Screws 1. Axle shaft drive flange
WHEEL HUB (INCLUDED WHEEL BEARING)
REMOVAL
1) Hoist vehicle and remove wheel.
2) Remove axle shaft drive flange (4WD vehicle) or hub cap (2WD
vehicle).
3) If equipped with ABS, remove wheel speed sensor from knuckle
and harness clamp from strut.
4) Remove caliper bolt and suspend caliper.
CAUTION:
Hang removed caliper with a wire hook or the like so as to
prevent brake hose from bending and twisting excessively
or being pulled.
Don't operate brake pedal with pads removed.
5) Remove brake disc.
NOTE:
If brake disc can not be removed by hand, use 8 mm bolts as
shown.
6) Remove front wheel bearing lock washer by loosening 4 screws.
7) Remove front wheel bearing lock nut by using special tool.
Special Tool
(A): 09951-16050
8) Remove front wheel bearing washer.
9) Remove wheel hub component by hand.

YH4
GRAND
VITARA
2, (b)
1
1. Circlip
2. Large diameter
1. Front wheel speed sensor
2. Bolt
FRONT SUSPENSION 3D-15
7) For 4WD vehicle, apply lithium grease to front drive shaft wash-
er and front wheel spindle outer.
ªAº: Grease 99000-25010
8) For 4WD vehicle, when installing circlip to drive shaft, utilize
screw hole in drive shaft to pull it out and bring large diameter
of circlip at right as shown.
9) For vehicle with ABS, check that no foreign material is attached
to sensor and rotor. Install wheel speed sensor and its harness
clamp.
Tightening Torque
(a): 10 N
.m (1.0 kg-m, 7.5 lb-ft)
(b): 23 N
.m (2.3 kg-m, 17.0 lb-ft)
CAUTION:

Do not pull wire harness or twist more than necessary
when installing front wheel speed sensor.

Fit harness grommet to inner fender securely.
Check that there is no clearance between sensor and knuckle.
10) Install brake disc and caliper assembly.
Tightening Torque
(e): 85 N
.m (8.5 kg-m, 61.5 lb-ft)