Outer SUZUKI GRAND VITARA 2000 2.G Service Workshop Manual

YH4
GRAND
VITARA
HEATER AND VENTILATION 1A-3
BODY VENTILATION
The body ventilation system of this vehicle has a fresh air intake located at the cowl top panel. When fresh air intake
control lever is at FRESH AIR position, ventilating air is drawn into the interior from the cowl center garnish and
drawn out from the ventilator outlet provided at each side body outer panel (both right and left side).
DIAGNOSIS
DIAGNOSIS TABLE
TroublePossible causeRemedy
Heater blower won't
work even when its
switch is ON.Blower fuse blown
Blower resistor faulty
Blower motor faulty
Wiring or grounding faultyReplace fuse to check for short.
Check resistor.
Replace motor.
Repair as necessary.
Incorrect temperature
output.Control cables broken or binding
Air damper broken
Air ducts clogged
Heater radiator leaking or clogged
Heater hoses leaking or cloggedCheck cables.
Repair damper.
Repair air ducts.
Replace radiator.
Replace hoses.
When mode control
switch is changed,
air outlet port is not
changed.Mode control switch faulty
Mode actuator faulty
Fuse blown
Wiring or grounding faulty
Air damper broken
Air ducts cloggedCheck and replace as necessary.
Check and replace as necessary.
Replace fuse to check for short.
Repair as necessary.
Repair damper.
Repair air ducts.

YH4
GRAND
VITARA
3D-10 FRONT SUSPENSION
ªaº < ªbº
1. Circlip
2. Large diameter
1. Axle shaft drive flange
2. Bolt 1. Spring seat
Bottom
INSTALLATION
Reverse removal procedure to install coil spring.
NOTE:
Upper and lower diameters of coil spring are different.
Bring larger diameter end at bottom and set its open end in
place on spring seat.

Be sure to use specified torque for tightening each fastener.

Refer to torque specification chart at the end of this section.

As for ball stud nut, be sure to insert split pin and bend it after tight-
ening it.

Tighten tie-rod end nut with pushing ball stud to upper side so as
not ball stud to be rotated.

For 4WD vehicle
Apply lithium grease to front drive shaft washer and front wheel
spindle outer.
ªAº: Grease 99000-25010

For 4WD vehicle
When installing circlip to drive shaft, utilize screw hole in drive
shaft to pull it out and bring large diameter of circlip at right as
shown.

For 4WD vehicle
When installing axle shaft drive flange to wheel hub, apply sealant
to mating surface of axle shaft drive flange and tighten flange bolt
to specified torque.
ªAº: Sealant 99000-31090
Tightening Torque
(a): 50 N
.m (5.0 kg-m, 36.5 lb-ft)

YH4
GRAND
VITARA
2, (b)
1
1. Circlip
2. Large diameter
1. Front wheel speed sensor
2. Bolt
FRONT SUSPENSION 3D-15
7) For 4WD vehicle, apply lithium grease to front drive shaft wash-
er and front wheel spindle outer.
ªAº: Grease 99000-25010
8) For 4WD vehicle, when installing circlip to drive shaft, utilize
screw hole in drive shaft to pull it out and bring large diameter
of circlip at right as shown.
9) For vehicle with ABS, check that no foreign material is attached
to sensor and rotor. Install wheel speed sensor and its harness
clamp.
Tightening Torque
(a): 10 N
.m (1.0 kg-m, 7.5 lb-ft)
(b): 23 N
.m (2.3 kg-m, 17.0 lb-ft)
CAUTION:

Do not pull wire harness or twist more than necessary
when installing front wheel speed sensor.

Fit harness grommet to inner fender securely.
Check that there is no clearance between sensor and knuckle.
10) Install brake disc and caliper assembly.
Tightening Torque
(e): 85 N
.m (8.5 kg-m, 61.5 lb-ft)

YH4
GRAND
VITARA
FRONT SUSPENSION 3D-21
(1)
(2)
(A)
1. Hydraulic press
1. Hydraulic press Cut off flange
Bush outer diameter
SUSPENSION CONTROL ARM / BUSHINGS
REMOVAL
1) Remove coil spring. Refer to COIL SPRING in this section.
2) Remove control arm bolts and nuts. Then remove control arm.
3) Cut flange part of control arm bush (rubber and steel) with using
care not to damage control arm end surface.
Dimension ªAº: Approx. 6 mm (0.236 in.)
4) Place control arm and special tool on hydraulic press. Set con-
trol arm cutting flange to welded part (1) of the special tool and
control arm joint side to the stepped part (2) of special tool.
CAUTION:
Use special care in driving out control arm bush to press
it vertically.
Or it may cause personally injury.
Special tool
(A): 09951-46020
5) Remove front bushing by using hydraulic press and special
tools, pull out bushing.
Special Tool
(A): 09951-46020
(B): 09924-74510
(C): 09951-16060
6) Remove rear bushing by using hydraulic press and special
tools, pull out bushing.
Special Tool
(A): 09951-46020
(D): 09913-80112
(E): 09925-58210

YH4
GRAND
VITARA
3D-24 FRONT SUSPENSION
REQUIRED SERVICE MATERIALS
MATERIALSRECOMMENDED
SUZUKI PRODUCTUSENO.
Lithium greaseSUZUKI SUPER GREASE (A)
(99000-25010)
Bearing inner oil seal / drive shaft oil seal
Recess of wheel spindles
Spindle outer washer
Spindle part of drive shaft
Spindle bush (inside and flange part)
Spindle inner washera
b
c
d
e
f
SealantSUZUKI BOND NO. 1215
(99000-31110)Mating surfaces of wheel spindle
and knuckle1
Sealing compound
SUZUKI SEALING COM-
POUND 366E
(99000-31090)
Front axle cap
Mating surfaces of wheel hub and drive
flange
Knuckle cap
Hub capA
B
C
D

YH4
GRAND
VITARA
4A2
1. Drive shaft oil seal
2. Double off set joint (DOJ)
3. Joint circlip
4. DOJ boot
5. Ball joint boot
6. Ball joint assembly (RH side)
7. Drive shaft assembly (LH side)
8. Left drive shaft
9. Drive shaft bearing circlip
10. Drive shaft bearing
FRONT DRIVE SHAFT / SHAFT BEARING, OIL SEAL 4A2-1
SECTION 4A2
FRONT DRIVE SHAFT/SHAFT BEARING,
OIL SEAL
CONTENTS
GENERAL DESCRIPTION4A2- 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DIAGNOSIS4A2- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnosis Table4A2- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Drive Shaft Boot And Joint Check 4A2- 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE4A2- 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Drive Shaft4A2- 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Shaft Bearing / Oil Seal4A2- 9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TIGHTENING TORQUE SPECIFICATIONS4A2-11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REQUIRED SERVICE MATERIALS4A2-11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPECIAL TOOLS4A2-11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GENERAL DESCRIPTION
The drive shaft joint is a constant velocity joint (C.V. joint) which slides in the axial direction. The joint is composed
of an outer race, cage, inner race and balls. In the turning direction, the joint rotates in the same way as a ball bear-
ing. The balls lock rotation completely and transmit drive. In addition this vehicle is also characterized by a function
that the shaft can slide through the balls in the grooves of the outer race in the extension / contraction direction of
the drive shaft.

YH4
GRAND
VITARA
1. Boot
2. Snap ring
1. Circlip
2 Snap ring plier
3. Cage
FRONT DRIVE SHAFT / SHAFT BEARING, OIL SEAL 4A2-5
DISASSEMBLY
1) Remove boot band of differential side joint.
2) Slide boot toward the center of shaft and remove snap ring from
outer race, then take shaft out of outer race.
3) Remove circlip and then cage.
4) Remove inside and outside boots from shaft.
CAUTION:

Do not disassemble wheel side joint (outboard joint). If
any malcondition is found in joint, replace it as assem-
bly.

Do not disassemble ball joint of differential side joint.
If any malcondition is found in ball joint, replace differ-
ential side joint assembly.
INSPECTION

Check boots for breakage or deterioration. Replace them as nec-
essary.

Check circlip, snap ring and boot bands for breakage or deforma-
tion. Replace as necessary.
CLEANING

Wash disassembled parts (except boots) in degreaser. After
washing, dry parts completely by blowing air.

Clean boots with cloth. DO NOT wash boots in degreaser, such
as gasoline or kerosene, etc.
Washing in degreaser causes deterioration of boot.

YH4
GRAND
VITARA
ªAº: Fill grease 90 ± 95 g (3.2 ± 3.4 oz)
1. Circlip
[LH] [RH] Differential side
FRONT DRIVE SHAFT / SHAFT BEARING, OIL SEAL 4A2-7
7) Apply grease to entire surface of cage.
Use joint grease in tube included in spare part or joint grease
(99000-25120).
8) Insert cage into outer race and fit circlip into groove of outer
race.
CAUTION:
Position opening of circlip ªaº so that it will not be lined
up with a ball.
9) Apply grease to inside of outer race, and fit boot to outer race.
Fill up inside of boot with joint grease.
ªAº: Joint Grease 99000-25120
(about 90 ± 95g / 3.2 ± 3.4 oz)
10) Fitting boot to outer race, adjust so that measurements ªbº and
ªcº become as indicated in figure.
Length ªbº: 203.2 ± 213.2 mm
(8.00 ± 8.40 in.)
196.8 ± 206.8 mm
(7.75 ± 8.14 in.) M
/
T vehicle with . . . . . . . . .
H25 engine
ªcº: 125.5 ± 135.5 mm
(4.94 ± 5.33 in.)
127.5 ± 137.5 mm
(5.02 ± 5.41 in.) M
/
T vehicle with . . . . . . . . .
H25 engine
Before fixing boot band, insert screwdriver into boot on joint
side and allow air to enter boot so that air pressure in boot be-
comes the same as atmospheric pressure.
11) Clamp boot band. Check boots for distortion or dent.

YH4
GRAND
VITARA
1. Drive shaft oil seal
1. Drive shaft flange bolt and nut
2. Front spindle thrust washer
3. Axle shaft drive flange
ªAº
1. Drive shaft joint
2. Oil seal
3. Pipe
4. Thrust washer4
4A2-8 FRONT DRIVE SHAFT / SHAFT BEARING, OIL SEAL
INSTALLATION
Install drive shaft assembly by reversing removal procedure and
noting following points.

Clean front drive shaft oil seal and then apply lithium grease to oil
seal and DOJ shaft.
ªAº: Grease 99000-25010

Check oil seal for breakage or deterioration.
Replace it as necessary.

Drive in oil seal until its end contacts stepped surface of drive
shaft joint by using a pipe whose inner diameter is 76 mm (2.992
in.) or more and outer diameter is 80 mm (3.150 in.) or less.
Diameter ªaº: 76 mm (2.992 in.) or more
Diameter ªbº: 80 mm (3.150 in.) or less

Drive in drive shaft thrust washer (Vehicle with G16 or J20 en-
gine).

RH Side
Push differential side joint by hand until it is positioned by snap
ring fitted to its spline.
LH Side
Connect drive shaft flange bolts and nuts.
Tightening Torque
(a): 50 N
.m (5.0 kg-m, 36.5 lb-ft)

Apply grease to front spindle thrust washer and front spindle part
of drive shaft.
ªAº: Grease 99000-25010

When installing axle shaft drive flange to wheel hub, apply sealant
to mating surface of axle shaft drive flange.
ªBº: Sealant 99000-31090
Tightening Torque
(b): 50 N
.m (5.0 kg-m, 36.5 lb-ft)
CAUTION:

To prevent breakage of boots (wheel side and differen-
tial side), be careful not to bring them into contact with
other parts when installing drive shaft assembly.

Do not pull housing of differential side joint.
If housing is pulled, it may be detached from drive shaft.

Fill specified differential gear oil into differential case to specified
level.

YH4
GRAND
VITARA
5-10 BRAKES
BRAKE PEDAL PLAY CHECK
Pedal play should be within specification. If out of specification,
check brake light switch for proper installation position and adjust
if necessary.
Also check pedal shaft bolt and master cylinder pin installation for
looseness and replace if defective.
Pedal play ªdº: 1 ± 8 mm (0.04 ± 0.32 in.)
BRAKE FLUID LEVEL CHECK
Be sure to use particular brake fluid either as indicated on reservoir
cap of that vehicle or recommended in owner's manual which
comes along with that vehicle.
Use of any other fluid is strictly prohibited.
Fluid level should be between MIN and MAX lines marked on reser-
voir.
When warning light lights sometimes during driving, replenish fluid
to MAX line.
When fluid decreases quickly, inspect brake system for leakage.
Correct leaky points and then refill to specified level.
CAUTION:
Do not use shock absorber fluid or any other fluid which
contains mineral oil. Do not use a container which has been
used for mineral oil or a container which is wet from water.
Mineral oil will cause swelling and distortion of rubber parts
in hydraulic brake system and water mixed into brake fluid
will lower fluid boiling point. Keep all fluid containers
capped to prevent contamination.
BRAKE HOSE AND PIPE CHECK
The brake hose assembly should be checked for road hazard dam-
age, for cracks and chafing of the outer cover, for leaks and blisters.
A light and mirror may be needed for an adequate inspection. If any
of the above conditions are observed on the brake hose, it is neces-
sary to replace it.
Inspect the pipe for damage, cracks, dents and corrosion. If any de-
fect is found, replace it.
MASTER CYLINDER CHECK
Check for a cracked master cylinder casting or brake fluid around
the master cylinder. Leaks are indicated only if there is at least a
drop of fluid. A damp condition is not abnormal.