short SUZUKI GRAND VITARA 2003 2.G Service Owner's Manual

YH4
GRAND
VITARA
AUTOMATIC TRANSMISSION (4 A / T) 7B1-33
O / D cut
switchOFF ON
VoltageBattery
voltage0 V
DIAGNOSTIC FLOW TABLE A-2 (NO GEAR SHIFT TO O / D)
SYSTEM DESCRIPTION
PCM does not shift to O / D gear under any of the following conditions.

O / D cut switch: ON

4WD LOW switch: ON

Cruise control module: O / D OFF command signal is output (if equipped).

ECT: ECT < 30C (86F)
TROUBLESHOOTING
WARNING:

When performing a road test, select a place where there is no traffic or possibility of a traffic accident
and very careful during testing to avoid occurrence of an accident.

Road test should be carried out with 2 person, a driver and tester, on a level road.
STEPACTIONYESNO
1Was ªAUTOMATIC TRANSMISSION
DIAGNOSTIC FLOW TABLEº performed?Go to Step 2.Go to ªAUTOMATIC
TRANSMISSION
DIAGNOSTIC FLOW
TABLEº.
2ECT check:
(1) Warm up engine to normal operating
temperature.
(2) Check ECT using scan tool.
Is ECT more than 30C (86F)?Go to Step 3.Faulty ECT sensor,
its circuit or engine
cooling system.
If OK, substitute a known-
good PCM and recheck.
3Perform running test under the following
conditions and check voltage between
C51-1-2 (G16 / J20 engines) or C51-1-6 (H25
engine) terminal of PCM coupler and ground,
C51-1-1 terminal of PCM coupler and ground.

O / D cut switch OFF (ªO / D OFFº lamp OFF).

Normal mode in ªDº range.

Transfer ª2Hº position.

Cruise control is not operated (if equipped).

Drive vehicle with 4th gear condition
referring to ªGear shift diagramº in this
section.
Is each voltage about 0 V?Faulty shift solenoid
valve, its circuit or
transmission.ªGº wire or ªG / Rº wire
shorted to power circuit.
If OK, go to Step 4.
4O / D cut switch signal inspection:
(1) With ignition switch ON, check voltage
between E61-33 (G16 / J20 engines) or
E61-14 (H25 engine) terminal of PCM
coupler and ground.
Is the result as specified?Go to Step 5.Faulty O / D cut switch or
its circuit.
If OK, substitute a known-
good PCM and recheck.

YH4
GRAND
VITARA
7B1-36 AUTOMATIC TRANSMISSION (4 A / T)
Switch ON
positionSwitch OFF
positionSwitch ON
position
Switch OFF
position
DIAGNOSTIC FLOW TABLE B-2 ªO / D OFFº LIGHT CIRCUIT CHECK
(ªO / D OFFº LIGHT COMES ON STEADILY)
WIRING DIAGRAM ± Refer to Table B-1 in this section.
TROUBLESHOOTING
STEPACTIONYESNO
1Check O / D cut Switch Position.
Is O / D cut switch turned OFF (Is switch button at OFF
position)?Go to Step 2.Turn O / D cut switch
OFF.
2Check Lamp Circuit for Short.
1) Turn ignition switch OFF and disconnect PCM
connectors.
2) Turn ignition switch ON.
Does ªO / D OFFº lamp come ON steadily?ªW / Bº circuit shorted
to ground.Go to Step 3.
3Check O / D cut Switch Circuit.
1) Check resistance between terminal E61-33
(G16 / J20 engines) or E61-14 (H25 engine) of
disconnected PCM connector and body ground with
O / D cut switch OFF.
Is continuity indicated?Go to Step 4.Check PCM ground
circuit for open.
If ground circuit is
OK, substitute a
known-good PCM
and recheck.
4Check O / D cut Switch for Operation.
1) Remove console box.
2) Disconnect O / D cut switch connector.
3) Check continuity between switch terminals under
each condition below.
Switch OFF position: No continuity
Switch ON position: Continuity
Is check result satisfactory?ªY / Rº circuit shorted
to ground.Replace O / D cut
switch.
Fig. for Step 1. Fig. for Step 4.

YH4
GRAND
VITARA
7B1-38 AUTOMATIC TRANSMISSION (4 A / T)
ª5º
ª4º
DIAGNOSTIC FLOW TABLE B-4 ªPOWERº LIGHT CIRCUIT CHECK
(ªPOWERº LIGHT COMES ON STEADILY)
WIRING DIAGRAM ± Refer to Table B-3 in this section.
TROUBLESHOOTING
STEPACTIONYESNO
1Check Power / Normal Change Switch Position.
Is switch button at Normal position?Go to Step 2.Set Power / Normal
change switch at
Normal position.
2Check Lamp Circuit for Short.
1) Turn ignition switch OFF and disconnect PCM
connectors.
2) Turn ignition switch ON.
Does ªPOWERº lamp come ON steadily?ªGr / Blº circuit
shorted to ground.Go to Step 3.
3Check Power / Normal Change Switch Circuit.
1) Check resistance between terminal E61-31
(G16/J20 engines) or E61-9 (H25 engine) of
disconnected PCM connector and body ground with
P / N change switch OFF.
Is continuity indicated?Go to Step 4.Check PCM ground
circuit for open.
If ground circuit is
OK, substitute a
known-good PCM
and recheck.
4Check Power / Normal Change Switch for Operation.
1) Remove Power / Normal change switch.
2) Check continuity between switch terminals ª4º and
ª5º under each condition below.
Normal position: No continuity
Power position: Continuity.
Is check result satisfactory?ªOr / Blº circuit
shorted to ground.Replace Power /
Normal change
switch.
Fig. for Step 1. Fig. for Step 4.

YH4
GRAND
VITARA
AUTOMATIC TRANSMISSION (4 A / T) 7B1-41
C51-1
-18C51-1
-17C51-1
-16C51-1
-15C51-1
-28C51-1
-27 G16/
J20
H25
C51-1-4 C51-1-3 C51-1-13 C51-1-12 C51-1-20 C51-1-19
Terminal
Select
lever
position
TROUBLESHOOTING (DTC P0705)
STEPACTIONYESNO
1Was ªA / T DIAG. FLOW TABLEº performed?Go to Step 2.Go to ªA / T DIAG.
FLOW TABLEº.
2Check Transmission Range Switch (Sensor) Circuit for
Operation.
When using SUZUKI scan tool:
1) Connect SUZUKI scan tool to DLC with ignition
switch OFF.
2) Turn ignition switch ON and check transmission
range signal (P, R, N, D, 2 or L) on display
when shifting select lever to each range.
Is applicable range indicated?
When not using SUZUKI scan tool:
1) Turn ignition switch ON.
2) Check voltage at terminals C51-1-15, C51-1-16,
C51-1-17, C51-1-18, C51-1-27 and C51-1-28 for
G16/J20 (C51-1-4, C51-1-3, C51-1-13, C51-1-12,
C51-1-20 and C51-1-19 for H25) respectively with
select lever shifted to each range.
Taking terminal C51-1-28 for G16/J20 (C51-1-20 for
H25) as an example, is battery voltage indicated
only when select lever is shifted to ª2º range and
0 V for other ranges as shown in figure?
Check voltage at other terminals likewise, referring
to figure.
Are check results satisfactory?Intermittent trouble.
Check for intermittent
referring to ªIntermit-
tent and Poor
Connectionº in
section 0A.Go to Step 3.
3Check Select Cable for Adjustment referring to ªSelect
Cable Adjustmentº in this section.
Is it adjusted correctly?Go to Step 4.Adjust.
4Check Transmission Range Switch for Installation
Position.
1) Shift select lever to ªNº range.
2) Check that ªNº reference line on switch and center
line on shaft are aligned.
Are they aligned?Go to Step 5.Adjust.
5Check Transmission Range Switch (Sensor) referring
to ªTransmission Range Switchº in this section.
Are check results satisfactory?ªYº, ªOr / Gº, ªRº,
ªOr / Blº, ªY / Gº,
ªG / Orº or ªG / Blº
circuit open or short.
If wires and
connections are OK,
substitute a known-
good PCM and
recheck.Replace TR switch.
Fig. for Step 2.

YH4
GRAND
VITARA
Oscilloscope waveforms
2V/Div.
Waveforms at specified idle
speed in ªPº range5ms / Div.
AUTOMATIC TRANSMISSION (4 A / T) 7B1-43
TROUBLESHOOTING (DTC P0715)
STEPACTIONYESNO
1Was ªA / T DIAG. FLOW TABLEº performed?Go to Step 2.Go to ªA / T DIAG.
FLOW TABLEº.
2Input speed sensor circuit check:
1) Remove PCM cover.
2) With ignition switch OFF, disconnect PCM
connectors.
3) Check for proper connection to input speed sensor
at C51-1-10 and C51-1-11 terminals for G16/J20
(at C51-1-8 and C51-1-16 terminals for H25)
4) If OK, check resistance of sensor circuit.
Resistance between C51-1-10
and C51-1-11 for G16 / J20
(C51-1-8 and C51-1-16 for H25):530 ± 650
at
20C, 68F
Resistance between C51-1-10 /
C51-1-11 for G16 / J20 (C51-1-8 /
C51-1-16 for H25) and ground: 1 M
or more
Are check results satisfactory?Go to Step 4.Go to Step 3.
3Input speed sensor check:
1) With ignition switch OFF, disconnect input speed
sensor connector.
2) Check for proper connection to input speed sensor
at each terminals.
3) If OK, then check resistance of input speed sensor.
Are measured values as specified in Step 2?ªBl / Gº or ªBl / Yº wire
open or shorted to
ground.Replace input speed
sensor.
4Check visually input speed sensor and overdrive clutch
drum for the followings.

No damage

No foreign material attached

Correct installation
Are they in good condition?Intermittent trouble
or faulty PCM.
Check for intermittent
referring to
ªIntermittent and
Poor Connectionº in
Section 0A.Clean, repair or
replace.
Reference
Connect oscilloscope between C51-1-11 (+) and C51-1-10 (±) for
G16 / J20 (C51-1-16 (+) and C51-1-8 (±) for H25) of PCM connector
connected to PCM and check input speed sensor signal.

YH4
GRAND
VITARA
Oscilloscope waveforms
2 V/Div.
5 ms / Div.
Waveforms at about 25 mph, 40 km / h
AUTOMATIC TRANSMISSION (4 A / T) 7B1-45
TROUBLESHOOTING (DTC P0720)
STEPACTIONYESNO
1Was ªA / T DIAG. FLOW TABLEº performed?Go to Step 2.Go to ªA / T DIAG.
FLOW TABLEº.
2Output speed sensor circuit check:
1) Remove PCM cover.
2) With ignition switch OFF, disconnect PCM
connectors.
3) Check for proper connection to output speed sensor
at C51-1-22 and C51-1-23 terminals for G16 / J20
(at C51-1-9 and C51-1-10 terminals for H25).
4) If OK, check resistance of sensor circuit.
Resistance between C51-1-22
and C51-1-23 for G16 / J20
(C51-1-9 and C51-1-10 for H25): 387 ± 473
at
20 C, 68 F
Resistance between C51-1-22 /
C51-1-23 for G16/J20 (C51-1-9 /
C51-1-10 for H25) and ground: 1 M
or more
Are check results satisfactory?Go to Step 4.Go to Step 3.
3Output speed sensor check:
1) With ignition switch OFF, disconnect output speed
sensor connector.
2) Check for proper connection to output speed sensor
at each terminals.
3) If OK, then check resistance of output speed sensor.
Are measured values as specified in Step 2?ªOrº or ªWº wire
open or shorted to
ground.Replace output
speed sensor.
4Check visually output speed sensor and sensor rotor
for the followings.

No damage

No foreign material attached

Correct installation
Are they in good condition?Intermittent trouble
or faulty PCM.
Check for intermittent
referring to
ªIntermittent and
Poor Connectionº in
Section 0A.Clean, repair or
replace.
Reference
Connect oscilloscope between C51-1-23 (+) and C51-1-22 (±) for
G16/J20 (C51-1-10 (+) and C51-1-9 (±) for H25) of PCM connector
connected to PCM and check output speed sensor signal.

YH4
GRAND
VITARA
7B1-48 AUTOMATIC TRANSMISSION (4 A / T)
TROUBLESHOOTING
STEPACTIONYESNO
1Was ªA / T DIAG. FLOW TABLEº performed?Go to Step 2.Go to ªA / T DIAG.
FLOW TABLEº.
2Is the vehicle equipped with monitor connector?Go to Step 3.Go to Step 4.
3Is DTC NO.65?G to Step 4.Go to Step 6.
4Check TCC Solenoid Circuit for Open or Short.
1) Turn ignition switch OFF and disconnect PCM
connectors.
2) Check for proper connection to PCM at terminals
C51-1-8 for G16 / J20 (C51-1-2 for H25).
3) If OK, then measure resistance between terminal
C51-1-8 for G16 / J20 (C51-1-2 for H25) of
disconnected PCM connector and ground.
Is it 11 ± 15
at 20
C, 68
F?Go to Step 5.ªG / Yº circuit open or
shorted to ground.
If wire and
connections are OK,
replace malfunction
shift solenoid.
5Check TCC Solenoid Circuit for Short.
1) Turn ignition switch ON.
2) Measure voltage between terminal C51-1-8 for
G16 / J20 (C51-1-2 for H25) of disconnected PCM
connector and ground.
Is it about 0 V?Intermittent trouble or
faulty PCM.
Check for
ªIntermittent and
Poor Connectionº in
Section 0A.ªG / Yº circuit shorted
to power circuit.
6Check TCC Solenoid Circuit for Short.
1) Turn ignition switch OFF and disconnect PCM
connectors.
2) Check for proper connection to PCM at terminals
C51-1-8 for G16 / J20 (C51-1-2 for H25) or C51-1-1.
3) If OK, then measure resistance between terminal
C51-1-8 for G16 / J20 (C51-1-2 for H25) of
disconnected PCM connector and ground.
Is it 11 ± 15
at 20
C, 68
F?Intermittent trouble or
faulty PCM.
Check for
ªIntermittent and
Poor Connectionº in
Section 0A.ªG / Yº circuit shorted
to ground.
If wire and
connections are OK,
replace malfunction
shift solenoid.

YH4
GRAND
VITARA
AUTOMATIC TRANSMISSION (4 A / T) 7B1-51
DTC CONFIRMATION PROCEDURE
WARNING:

When performing a road test, select a place where there is no traffic or possibility of a traffic accident
and be very careful during testing to avoid occurrence of an accident.

Road test should be carried out with 2 persons, a driver and a tester, on a level road.
1) Connect scan tool to DLC with ignition switch OFF, if available.
2) Clear DTC.
3) Start engine and shift transfer lever to ª2Hº or ª4Hº range.
4) Shift selector lever in D range and keep it for 10 seconds.
5) Drive vehicle about 30 km / h (20 mph) with 2nd gear in D range for 10 seconds.
6) Increase vehicle speed to about 80 km / h (50 mph) with 4th gear in D range and keep it for 10 seconds.
7) Release accelerator pedal, decrease vehicle speed and stop vehicle.
8) Check DTC and / or pending DTC.
TROUBLESHOOTING (DTC P0753 / P0758)
STEPACTIONYESNO
1Was ªA / T DIAG. FLOW TABLEº performed?Go to Step 2.Go to ªA / T DIAG.
FLOW TABLEº.
2Is the vehicle equipped with monitor connector?Go to Step 3.Go to Step 4.
3Is DTC NO.61 or 63?Go to Step 4.Go to Step 6.
4Check Shift Solenoid Circuit for Open or Short.
1) Turn ignition switch OFF and disconnect PCM
connectors.
2) Check for proper connection to PCM at terminals
C51-1-2 for G16 / J20 (C51-1-6 for H25) or C51-1-1.
3) If OK, then measure resistance between terminal
C51-1-2 for G16 / J20 (C51-1-6 for H25) or C51-1-1
of disconnected PCM connector and ground.
Is it 11 ± 15
at 20C, 68F?Go to Step 5.ªGº or ªG / Rº circuit
open or shorted to
ground.
If wire and
connections are OK,
replace malfunction
shift solenoid.
5Check Shift Solenoid Circuit for Short.
1) Turn ignition switch ON.
2) Measure voltage between terminal C51-1-2 for
G16 / J20 (C51-1-6 for H25) or C51-1-1 of
disconnected PCM connector and ground.
Is it about 0 V?Intermittent trouble or
faulty PCM.
Check for
ªIntermittent and
Poor Connectionº in
Section 0A.ªGº or ªG / Rº circuit
shorted to power
circuit.
6Check Shift Solenoid Circuit for Short.
1) Turn ignition switch OFF and disconnect PCM
connectors.
2) Check for proper connection to PCM at terminals
C51-1-2 for G16 / J20 (C51-1-6 for H25) or C51-1-1.
3) If OK, then measure resistance between terminal
C51-1-2 for G16/J20 (C51-1-6 for H25) or C51-1-1
of disconnected PCM connector and ground.
Is it 11 ± 15
at 20C, 68F?Intermittent trouble or
faulty PCM.
Check for
ªIntermittent and
Poor Connectionº in
Section 0A.ªGº or ªG / Rº circuit
shorted to ground.

YH4
GRAND
VITARA
1
1. 4WD low switch
AUTOMATIC TRANSMISSION (4 A / T) 7B1-53
TROUBLESHOOTING (DTC P1875)
STEPACTIONYESNO
1Was ªA / T DIAG. FLOW TABLEº performed?Go to Step 2.Go to ªA / T DIAG.
FLOW TABLEº.
24WD low switch and its circuit check:
When using SUZUKI scan tool:
1) Connect SUZUKI scan tool to DLC with ignition
switch OFF.
2) Turn ignition switch ON.
3) Select ªData listº mode on scan tool.
4) Check 4WD low switch signal (ON or OFF) on
display when shifting transfer lever to each
position.
4H or 2H position : OFF
4L position : ON
Is OFF / ON displayed as described above?
When not using SUZUKI scan tool:
1) Remove PCM cover.
2) Turn ignition switch ON.
3) Check voltage at terminal C51-1-26 for G16 / J20
(C51-1-5 for H25) of PCM connector connected
when shifting transfer lever to each position.
4H or 2H position : 10 ± 14 V
4L position : 0 ± 1 V
Is voltage as specified?Check for poor con-
nection at the termi-
nal of PCM if voltme-
ter is used in Step 2.
If connection is OK,
intermittent trouble
or faulty PCM.
Check for intermittent
referring to ªIntermit-
tent and Poor
Connectionº in
Section 0A.Go to Step 3.
34WD low switch check:
1) Check 4WD low switch for operation referring to
ª4WD Low Switch Inspectionº below.
Is check result satisfactory?ªOr / Wº or ªBº circuit
open or short. If wires
and connections are
OK, substitute a
known-good PCM
and recheck.Replace 4WD low
switch.
4WD Low Switch Inspection
1) Disconnect negative cable at battery.
2) Disconnect 4WD low switch coupler.
3) Check continuity between 4WD low switch terminals.
There should be continuity when transfer lever shifted to 4L posi-
tion and should be infinity when transfer lever shifted to 4H or 2H
positions.
If not, replace 4WD low switch.
4) Connect 4WD low switch coupler and battery negative cable.

YH4
GRAND
VITARA
8B-4 LIGHTING SYSTEM
DIAGNOSIS
NOTE:
Fuse name (ª º) in the table below is shown on the fuse box cover (Hard Top Model) or the junction box
(Canvas Top Model).
HEADLIGHTS
TroublePossible causeCorrection
Only one light does not
light
Bulb blown

Headlight L or R fuse blown

Socket, wiring or grounding faultyReplace bulb
Replace fuse to check for short
Repair
Headlights do not light
Headlight L and R fuses blown

Lighting and dimmer switch faulty

Defective light relay

Wiring or grounding faultyReplace fuses to check for short
Replace switches
Replace light relay
Repair
Only one beam (ªHiº or
ªLoº) does not light
Bulb blown

Lighting or dimmer switch faultyReplace bulb
Replace switch
HEADLIGHTS WITH LEVELING SYSTEM (IF EQUIPPED)
TroublePossible causeCorrection
Both headlights do not
move
ªTURN / BACKº fuse blown (Hard Top Model)
ªTRNº fuse blown (Canvas Top Model)

Leveling switch faulty

Supply voltage too lowReplace fuse to check for short
Replace switch
Recharge or replace battery
One of headlights (either
Right or Left) does not
move
Socket, wiring or grounding faulty

Actuator faulty

Vehicle body around headlight deformed

Headlight ass'y itself deformedRepair
Replace actuator
Repair body
Replace headlight ass'y
TURN SIGNAL AND HAZARD WARNING LIGHTS
TroublePossible causeCorrection
Flash rate high or one side
only flashes
Incorrect bulb

One of light bulbs burnt out

Turn signal / hazard warning relay faulty

Open circuit or high resistance existing
Replace bulb
Replace
Replace relay
Repair
Oen circuit or high resistance existing
between turn signal / hazard warning
switch and lights on one side

Wiring or grounding faulty
Re air
Repair
No flashing
ªTURN / BACKº and / or ªHAZARDº fuse(s)
blown (Hard Top Model)
ªTRNº and / or ªHAZº fuse(s) blown
(Canvas Top Model)

Open circuit or high resistance existing
between battery and switch

Turn signal / hazard relay faulty

Combination switch or hazard switch faulty

Wiring or grounding faultyReplace fuse(s) to check for
short
Check bulb and check circuit
Replace relay
Replace switch
Repair
Flash rate low
Supply voltage too low

Turn signal / hazard relay faultyCheck charging system
Replace relay