stop start SUZUKI NEXA 2015 1.G Owners Manual
Page 35 of 288
Downloaded from www.Manualslib.com manuals search engine
% ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
outside, or using the door lock knobs or
the central door locking switch from
inside.
• If any door is not operated within approx-
imately 30 seconds after the doors have
been unlocked using the keyless entry
system transmitter, keyless push start
system remote controller or request
switch, the doors are automatically
locked again. When the doors are
locked, the security system will be
armed in about 5 seconds if the system
is in the enabled state.
• If the security system indicator (1) blinks
when the ignition switch is in the “ON”
position or the ignition mode is “ON”,
there may be something wrong with the
security system. Ask your
D X W K R U L V H G 0 D U X W L 6 X ] X N L Z R U N V K R S to
inspect the system.
+ R Z W R G L V D U P W K H V H F X U L W \ V \ V W H P
Simply unlock the doors using the keyless
entry system transmitter, keyless push
start system remote controller or request
switch. The security system indicator will
go out, indicating that the security system
is disarmed.
+ R Z W R V W R S W K H D O D U P
Should the alarm be triggered accidentally,
unlock the doors using the keyless entry
system transmitter, keyless push start sys-
tem remote controller or request switch, or
insert the key in the ignition switch and turn
it to “ON” position, or press the engineswitch to change the ignition mode to
“ON”. The alarm will then stop.
NOTE:
• Even after the alarm has stopped, if you
lock the doors using the keyless entry
system transmitter, keyless push start
system remote controller or request
switch, the security system will be
rearmed with a delay of about 5 sec-
onds.
• If you disconnect the battery while the
security system is in the armed condition
or the alarm is actually in operation, the
alarm will be re-triggered when the bat-
tery is then reconnected.
• Even after the alarm has stopped at the
end of the predetermined operation time,
it will be triggered again if any of the
doors or engine hood is opened, or the
vehicle feels a shock (if the shock sen-
sor is in the enabled state), without dis-
arming the security system.
& K H F N L Q J Z K H W K H U W K H D O D U P K D V E H H Q
W U L J J H U H G G X U L Q J S D U N L Q J
If the alarm was triggered and you then
turn the ignition switch to “ON” position, or
press the engine switch to change the igni-
tion mode to “ON”, the security system
indicator will blink rapidly for about 8 sec-
onds and a buzzer will beep 4 times during
this period. If this happens, check whether
the vehicle has been broken into while you
were away from it. ( Q D E O L Q J D Q G G L V D E O L Q J W K H V H F X U L W \
V \ V W H P
The security system can be either enabled
or disabled.
: K H Q H Q D E O H G
• If any of the doors are opened without
unlocking by the keyless entry system
transmitter, keyless push start system
remote controller or request switch, all
turn signal lights start to blink and the
interior buzzer beeps intermittently. After
5 seconds, the siren will sound for about
27.5 seconds. The security system indi-
cator continues to blink during this time.
• If the engine hood is opened, all turn sig-
nal lights blink, and the siren sounds for
about 27.5 seconds. The security sys-
tem indicator continues to blink during
this time.
( , I W K H V K R F N V H Q V R U L V L Q W K H H Q D E O H G
V W D W H
• If the vehicle feels a shock, the siren
sounds for about 2 seconds (pre-warn-
ing). If the vehicle continues to feel a
shock, all turn signal lights start to blink
and the interior buzzer beeps intermit-
tently. After 5 seconds, the siren will
sound for about 27.5 seconds (full blast
warning). The security system indicator
continues to blink during this time.
NOTE:
If you set the full blast warning sensitivity
higher than the pre-warning sensitivity in
the setting mode of the information display,
or the vehicle feels such shock as to be
Page 70 of 288
Downloaded from www.Manualslib.com manuals search engine % ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
$ Y H U D J H 6 S H H G
If you selected average speed the last time
you drove the vehicle, the display indicates
the last value of average speed from
previous driving when the ignition switch is
turned to the “ON” position or the engine
switch is pressed to change the ignition
mode to “ON”. Unless you reset the value
of average speed, the display indicates the
value of average speed which includes
average speed during previous driving.
To reset the value of average speed, push
and hold the indicator selector knob (2) for
about 2 seconds when the display indicates
an average speed. The display shows “---”
and then indicates a new average speed
after driving for a short time.
NOTE:
When you reconnect the negative (–) ter-
minal to the battery, the value of average
speed will be shown after driving for a
period of time. 7 U L S 0 H W H UThe display (D) shows the trip meter.
The trip meter can be used to measure the
distance traveled on short trips or between
fuel stops.
You can use the trip meter A or trip meter B
independently.
To reset the trip meter to zero, push and
hold the trip meter selector knob (3) for
about 2 seconds when the display shows
the trip meter.
2 G R P H W H UThe display (E) shows the odometer.
The odometer records the total distance
the vehicle has been driven. 6 H W W L Q J 0 R G HWhen the ignition switch is in the “ON”
position or the ignition mode is ON and the
vehicle is stationary, you can enter the set-
ting mode of the information display by
pushing and holding the indicator selector
knob (2) for more than 3 seconds.
• To select the setting that you want to
change, turn the indicator selector knob
(2) left or right.
• To change the setting, push the indicator
selector knob (2).
• To exit the setting mode, select “Back”
and push the indicator selector knob (2).
61MM0A161
NOTE:
The currently selected setting item is indi-
cated enclosed by a frame.
NOTE:
• If you push and hold the indicator selec-
tor knob (2) to enter the setting mode
when the display (D) shows average fuel
consumption or average speed, the
value will be reset simultaneously. If you
do not want to reset the value, push the
indicator selector knob quickly to switch
the indication of the display.
• If you turn the ignition switch, press the
engine switch or start to move the vehi-
cle when the display is in the setting
mode, the setting mode will be canceled
automatically.
NOTICE
. H H S W U D F N R I \ R X U R G R P H W H U U H D G L Q J
D Q G F K H F N W K H P D L Q W H Q D Q F H V F K H G
X O H U H J X O D U O \ I R U U H T X L U H G V H U Y L F H V
, Q F U H D V H G Z H D U R U G D P D J H W R F H U W D L Q
S D U W V F D Q U H V X O W I U R P I D L O X U H W R S H U
I R U P U H T X L U H G V H U Y L F H V D W W K H S U R S H U
P L O H D J H L Q W H U Y D O V
( ; $ 0 3 / (
Page 80 of 288
Downloaded from www.Manualslib.com manuals search engine % ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
: D U Q L Q J D Q G , Q G L F D W R U / L J K W VNOTE:
If warning and indicator lights blink or
come on, the corresponding messages
may be shown on the information display.
% U D N H 6 \ V W H P : D U Q L Q J / L J K W
65D477
Three different types of operations exist
depending on the vehicle’s specification.
1) The light comes on briefly when the
ignition switch is turned to the “ON”
position or the engine switch is pressed
to change the ignition mode to “ON”.
2) The light comes on when the parking
brake is engaged with the ignition
switch in the “ON” position or the igni-
tion mode “ON”.
3) The light comes on when under either
or both of above two conditions.
The light also comes on when the fluid in
the brake fluid reservoir falls below the
specified level.
The light should go out after starting the
engine and fully releasing the parking
brake, if the fluid level in the brake fluid
reservoir is adequate.
If your vehicle is equipped with the ABS,
the brake system warning light also comes
on together with the ABS warning light
when the rear brake force control function(proportioning valve function) of the ABS
system fails.
If the brake system warning light comes on
while you are driving the vehicle, it may
mean that there is something wrong with
the vehicle’s brake system. If this happens,
you should:
1) Pull off the road and stop carefully.
2) Test the brakes by carefully starting and
stopping on the shoulder of the road.
3)If you determine that it is safe, drive
cautiously at low speed to the nearest
D X W K R U L V H G 0 D U X W L 6 X ] X N L Z R U N V K R S for
repairs, or
4) Have the vehicle towed to the nearest
D X W K R U L V H G 0 D U X W L 6 X ] X N L Z R U N V K R S for
repairs.
: $ 5 1 , 1 *
5 H P H P E H U W K D W V W R S S L Q J G L V W D Q F H
P D \ E H O R Q J H U \ R X P D \ K D Y H W R S X V K
K D U G H U R Q W K H S H G D O D Q G W K H S H G D O
P D \ J R G R Z Q I D U W K H U W K D Q Q R U P D O
Page 81 of 288
Downloaded from www.Manualslib.com manuals search engine
% ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
NOTE:
Because the brake system is self-adjust-
ing, the fluid level will drop as the brake
pads become worn. Replenishing the
brake fluid reservoir is considered normal
periodic maintenance.
NOTE:
(Parking Brake Reminder Buzzer)
A buzzer sounds intermittently to remind
you to release the parking brake if you
start the vehicle without releasing the park-
ing brake. Make sure that the parking
brake is fully released and the brake sys-
tem warning light turns off.
$ Q W L / R F N % U D N H 6 \ V W H P $ % 6
: D U Q L Q J / L J K W L I H T X L S S H G
65D529
When the ignition switch is turned to the
“ON” position or the engine switch is
pressed to change the ignition mode to
“ON”, the light comes on briefly so you can
check that the light is working.
If the light stays on, or comes on when
driving, there may be something wrong
with the ABS.
If this happens:
1) Pull off the road and stop carefully.
2) Turn the ignition switch to “LOCK” or
change the ignition mode to “LOCK”
(OFF) by pressing the engine switch
and then start the engine again.
If the warning light comes on briefly then
turns off, the system is normal. If the warn-
ing light still stays on.
If the light and the brake system warning
light stay on, or come on simultaneously
when driving, your ABS system is
equipped with the rear brake force control
function (proportioning valve function) andthere may be something wrong with both
the rear brake force control function and
anti-lock function of the ABS system.
If one of these happens, have the system
inspected by your D X W K R U L V H G 0 D U X W L 6 X ] X N L
Z R U N V K R S
If the ABS becomes inoperative, the brake
system will function as an ordinary brake
system that does not have this ABS sys-
tem.
For details of ABS system, refer to “Anti-
Lock Brake System (ABS)” in the “OPER-
ATING YOUR VEHICLE” section.
: $ 5 1 , 1 *
, I D Q \ R I W K H I R O O R Z L Q J F R Q G L W L R Q V
R F F X U \ R X V K R X O G L P P H G L D W H O \ D V N
\ R X U D X W K R U L V H G 0 D U X W L 6 X ] X N L Z R U N
V K R S W R L Q V S H F W W K H E U D N H V \ V W H P
G R H V Q R W J R R X W D I W H U W K H H Q J L Q H
K D V E H H Q V W D U W H G D Q G W K H S D U N L Q J
E U D N H K D V E H H Q I X O O \ U H O H D V H G
Page 82 of 288
Downloaded from www.Manualslib.com manuals search engine % ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
2 L O 3 U H V V X U H / L J K WThis light comes on when the ignition
switch is turned to the “ON” position or the
engine switch is pressed to change the
ignition mode to “ON”, and goes out when
the engine is started. The light will come
on and remain on if there is insufficient oil
pressure. If the light comes on when driv-
ing, pull off the road as soon as you can
and stop the engine.
& K D U J L Q J / L J K W
50G052
This light comes on when the ignition
switch is turned to the “ON” position or the
engine switch is pressed to change the
ignition mode to “ON”, and goes out when
the engine is started. The light will come on
and remain on if there is something wrong
with the battery charging system. If the light
comes on when the engine is running, the
charging system should be inspected
immediately by your D X W K R U L V H G 0 D U X W L
6 X ] X N L Z R U N V K R S.
' U L Y H U
Page 107 of 288
Downloaded from www.Manualslib.com manuals search engine
2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 (
5 H P R W H & R Q W U R O O H U 2 X W V L G H : D U Q L Q JWhen either of the conditions described
below is met, the system issues the remote
controller outside warning by sounding the
interior and exterior buzzers. At the same
time, the immobilizer/keyless push start
system warning light comes on and the
master warning indicator light blinks.
• Any door is opened and then closed
while the remote controller is not inside
the vehicle and the engine is running or
the ignition mode has been changed to
“ACC” or “ON” by pressing the engine
switch.
• The remote controller is not inside the
vehicle when you attempt to start the
engine after changing the ignition mode
to “ACC” or “ON” by pressing the engine
switch.
61MM0A182
(1) Immobilizer/keyless push start sys-
tem warning light (blinks)
(2) Master warning indicator light (blinks)
NOTE:
• If the warning is given, locate the remote
controller as soon as possible.
• Any attempt to start the engine will fail
while the warning is active. The mes-
sage appearing on the information dis-
play in the instrument cluster will also
indicate this condition. Refer to “Informa-
tion display” in the “BEFORE DRIVING”
section for details.
• Normally, the immobilizer/keyless push
start system warning light should go out
and the master warning indicator light
should stop blinking shortly after the
remote controller is brought back inside
the vehicle. If they remain lit and blink-
ing, change the ignition mode to “LOCK”
(OFF) by pressing the engine switch and
then perform the engine starting opera-
tion. Refer to “Starting the Engine” in this
section.
• Always keep the remote controller with
you as the driver.
, Q W H U L R U : R U N D E O H $ U H D I R U ( Q J L Q H
6 W D U W L Q J , J Q L W L R Q 0 R G H 6 H O H F W L R Q
D Q G 5 H P R W H & R Q W U R O O H U 2 X W V L G H
: D U Q L Q J
61MM0B002
(1) Interior workable area
The interior workable area for these func-
tions is defined as all the interior spaces
except for the space above the instrument
panel.
NOTE:
• Even when the remote controller is in the
“interior workable area”, if it is in any of
the following conditions, you may not be
able to start the engine or select the igni-
tion modes, and the remote controller
outside warning may be given.
– The remote controller’s battery is low.
– The remote controller is affected by
strong radio signals or noise.
– The remote controller is in contact with
or covered by a metallic object.
(1)
(2)
(1)
Page 109 of 288
Downloaded from www.Manualslib.com manuals search engine
2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 (
3 D U N L Q J % U D N H 5 H P L Q G H U % X ] ] H UA buzzer sounds intermittently to remind
you to release the parking brake if you start
the vehicle without releasing the parking
brake. Make sure that the parking brake is
fully released and the brake system warning
light turns off.
3 H G D O
80J2121
& O X W F K 3 H G D O The clutch pedal is used to disengage the
drive to the wheels when starting the
engine, stopping, or shifting the gearshift
lever. Depressing the pedal disengages the
clutch. % U D N H 3 H G D O Your vehicle is equipped with either front
and rear disc brakes or front disc brakes
and rear drum brakes. Depressing the
brake pedal applies both sets of brakes.
You may hear occasional brake squeal
when you apply the brakes. This is a nor-mal condition caused by environmental
factors such as cold, wet, snow, etc.
$ F F H O H U D W R U 3 H G D O This pedal controls the speed of the
engine. Depressing the accelerator pedal
increases power output and speed.
: $ 5 1 , 1 *
' R Q R W G U L Y H Z L W K \ R X U I R R W U H V W L Q J R Q
W K H F O X W F K S H G D O , W F R X O G U H V X O W L Q
H [ F H V V L Y H F O X W F K Z H D U F O X W F K G D P D J H
R U X Q H [ S H F W H G O R V V R I H Q J L Q H E U D N L Q J
(2)
(1)
(3) ( ; $ 0 3 / (
: $ 5 1 , 1 *
, I E U D N H V T X H D O L V H [ F H V V L Y H D Q G
R F F X U V H D F K W L P H W K H E U D N H V D U H
D S S O L H G \ R X V K R X O G K D Y H W K H E U D N H V
F K H F N H G E \ \ R X U D X W K R U L V H G 0 D U X W L
6 X ] X N L Z R U N V K R S
: $ 5 1 , 1 *
' R Q R W U L G H W K H E U D N H V E \ D S S O \ L Q J
W K H P F R Q W L Q X R X V O \ R U U H V W L Q J \ R X U
I R R W R Q W K H S H G D O 7 K L V Z L O O U H V X O W L Q
R Y H U K H D W L Q J R I W K H E U D N H V Z K L F K
F R X O G F D X V H X Q S U H G L F W D E O H E U D N L Q J
D F W L R Q O R Q J H U V W R S S L Q J G L V W D Q F H V R U
S H U P D Q H Q W E U D N H G D P D J H
Page 110 of 288
Downloaded from www.Manualslib.com manuals search engine 2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 ( 6 W D U W L Q J W K H ( Q J L Q H
9 H K L F O H Z L W K R X W . H \ O H V V 3 X V K
6 W D U W 6 \ V W H P
% H I R U H 6 W D U W L Q J W K H ( Q J L Q H
64MS146
1) Make sure the parking brake is set fully.
2) Shift into “N” (Neutral) and depress the
clutch pedal all the way to the floor. Hold
the clutch pedal while starting the
engine.
6 W D U W L Q J D & R O G D Q G : D U P ( Q J L Q H & R O G H Q J L Q H
Turn the ignition switch to the “ON” posi-
tion and wait until the glow plug indicator
goes out if it comes on. Crank the engine
by turning the ignition key to “START”.
Release the key when the engine starts.
: D U P H Q J L Q H
Crank the engine by turning the ignition
key to “START”. Release the key when the
engine starts.
& D X W L R Q Z K H Q V W R S S L Q J W K H H Q J L Q H Z L W K
W X U E R F K D U J H U
When stopping the engine after climbing or
high speed driving, let the engine idle for
about one minute or more (if it is not pro-
hibited) to cool down the turbocharger and
engine oil. This is to prevent the engine oil
from over-deteriorating. Deteriorated
engine oil will damage the bearings of the
turbocharger.
5 H V W D U W L Q J G L H V H O H Q J L Q H D I W H U I X H O
H P S W \ V W R S
If the engine stops and the low fuel warning
light and the malfunction indicator light
come on, use the following procedure:
1) Fill the fuel tank.
2) Hold the ignition key in “ON” position for
5-10 seconds to feed fuel.
3) Perform above engine starting proce-
dure to start the engine.
If the malfunction indicator light still comes
on after the engine started, there may be
some problem with the engine. Ask your
D X W K R U L V H G 0 D U X W L 6 X ] X N L Z R U N V K R S
to have
the
engine inspected.
: $ 5 1 , 1 *
Page 111 of 288
Downloaded from www.Manualslib.com manuals search engine
2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 ( 6 W D U W L Q J W K H ( Q J L Q H
9 H K L F O H Z L W K . H \ O H V V 3 X V K 6 W D U W
6 \ V W H P
% H I R U H 6 W D U W L Q J W K H ( Q J L Q H
64MS169
1) Make sure the parking brake is set fully.
2) Shift to “N” (Neutral) and fully depress
the clutch pedal. Hold the clutch and
brake pedals fully depressed.
82K254
3) The “PUSH START SWITCH” message
will appear on the information display in
the instrument cluster. Push the engine
switch (1). When the engine is started,
the starter motor will automatically stop.
NOTE:
• You do not need to keep the engine
switch pressed to start the engine.
• The engine of a manual transaxle vehi-
cle will not start unless the clutch pedal
is depressed.
• During the engine starting procedure,
messages on the information display will
help you. Refer to “Information Display”in the “BEFORE DRIVING” section for
details.
• You should turn off such loads as the
headlights and air conditioning system to
facilitate starting of the engine.
• Even if you fail to start the engine, the
starter motor will stop operating auto-
matically after a short time. After the
starter motor has stopped or if there is
some problem with the system, the
starter motor will rotate only while the
engine switch is being pressed.
6 W R S S L Q J W K H H Q J L Q H• Depress the engine switch to stop the
engine after the vehicle stopped com-
pletely.
• In case of emergency, you can stop the
engine by quickly pushing the engine
switch more than 3 times, or pushing
and holding the engine switch more than
2 seconds while the vehicle in motion.
NOTE:
Except in emergency, do not stop the
engine while the vehicle in motion.
The steering and braking operation will
require more efforts when the engine
stopped.
Refer to “Braking” in this section.
• If the engine has been stopped and
stayed as it as for while after the engine
was stopped unexpectedly or was raced
before stopped, a clicking sound may be
heard from around the engine when
engine restarted. This is not a malfunc-
(1)
: $ 5 1 , 1 *
0 D N H V X U H W K D W W K H S D U N L Q J E U D N H L V
V H W I X O O \ D Q G W K H W U D Q V D [ O H L V L Q 1 H X
W U D O E H I R U H D W W H P S W L Q J W R V W D U W W K H
H Q J L Q H
NOTICE
Page 112 of 288
Downloaded from www.Manualslib.com manuals search engine 2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 (
tion. In this case, always let the engine
idle before stop it. 6 W D U W L Q J D & R O G D Q G : D U P ( Q J L Q H & R O G H Q J L Q H
Depress the clutch and brake pedals fully
and press the engine switch to crank the
engine. If the glow plug indicator light
comes on, the engine will start automati-
cally after the glow plug indicator light goes
off or 10 seconds past.
: D U P H Q J L Q H
Crank the engine by pressing the engine
switch to change the ignition mode to
“START”. & D X W L R Q Z K H Q V W R S S L Q J W K H H Q J L Q H Z L W K
W X U E R F K D U J H U
When stopping the engine after climbing or
high speed driving, let the engine idle for
about one minute or more (if it is not pro-
hibited) to cool down the turbocharger and
engine oil. This is to prevent the engine oil
from over-deteriorating. Deteriorated
engine oil will damage the bearings of the
turbocharger.
5 H V W D U W L Q J G L H V H O H Q J L Q H D I W H U I X H O
H P S W \ V W R S
If the engine stops and the low fuel warn-
ing light and the malfunction indicator light
come on, use the following procedure:
1) Fill the fuel tank.
2) Press the engine switch to change the
ignition mode to “ON” for 5-10 seconds
to feed fuel.
3) Perform above engine starting proce-
dure to start the engine.
If the malfunction indicator light still comes
on after the engine started, there may be
some problem with the engine. Ask your
D X W K R U L V H G 0 D U X W L 6 X ] X N L Z R U N V K R S to have
the engine inspected.
, I W K H 0 $ 6 7 ( 5 : $ 5 1 , 1 * L Q G L F D W R U O L J K W
E O L Q N V D Q G W K H H Q J L Q H F D Q Q R W E H V W D U W H G
Your keyless push start system remote
controller may not be sensed as being
within the interior workable area. Try again
after making sure that you have the remote
controller with you. If the engine still can-
not be started, the battery of the remote
controller may be discharged. You mustthen use the following method to be able to
start the engine.
58MST0302
1) Make sure the parking brake is set fully.
2) Shift to “N” (Neutral) and fully depress
the clutch pedal. Hold the clutch and
brake pedals fully depressed.
3) The “PUSH START SWITCH.” mes-
sage will appear on the information dis-
play in the instrument cluster. Press the
engine switch (1).
4) Within about 10 seconds of blinking of
the “MASTER WARNING” indicator
light in the instrument cluster, touch the
engine switch with the lock button end
of the remote controller (2) for about 2
seconds.
NOTE:
• If you still cannot start the engine after
several attempts using the above
NOTICE
' R Q R W F U D Q N W K H H Q J L Q H I R U P R U H
W K D Q V H F R Q G V D W D W L P H
, I W K H H Q J L Q H G R H V Q