tailgate SUZUKI NEXA 2015 1.G Owners Manual

Downloaded from www.Manualslib.com manuals search engine 2-3BEFORE DRIVING
64MS0-74E
Door LocksSide Door Locks
64MS018
(1) LOCK
(2) UNLOCK
(3) Front
(4) Rear
To lock a front door from outside the vehi-
cle:
• Insert the key and turn the top of the key
toward the rear of the vehicle, or
• Turn the lock knob forward, then pull and
hold the door handle as you close the
door.
To unlock a front door from outside the
vehicle, insert the key and turn the top of
the key toward the front of the vehicle.
64MS019
(1) LOCK
(2) UNLOCK
To lock a door from inside the vehicle, turn
the lock knob forward. Turn the lock knob
rearward to unlock the door.
To lock a rear door from outside the vehi-
cle, turn the lock knob forward and close
the door. You do not need to pull and hold
the door handle as you close the door.
NOTE:
Be sure to hold the door handle when you
close a locked front door, or the door will
not remain locked.
Central Door Locking System
64MS020
(1) LOCK
(2) UNLOCK
(3) Front
(4) Rear
You can lock and unlock all doors (includ-
ing the tailgate) simultaneously by using
the key in the driver’s door lock.
To lock all doors simultaneously, insert the
key in the driver’s door lock and turn the
top of the key toward the rear of the vehi-
cle once.
To unlock all doors simultaneously, insert
the key in the driver’s door lock and turn
the top of the key toward the front of the
vehicle twice.
(1)
(2)
(4)
(3)
(1)
(2)
(4)
(3)
(1)
(2)
Door Lock Knob
EXAMPLE

Downloaded from www.Manualslib.com manuals search engine %()25('5,9,1*
06(
If you cannot unlatch the tailgate by pushing
the unlatch switch (1) due to a discharged
battery or malfunction, follow the proce-
dures below to unlatch the tailgate from
inside the vehicle.
1) Remove the luggage compartment
cover (if equipped) and fold the rear seat
forward for easier access. Refer to
“Folding Rear Seats” section for details
on how to fold the rear seat forward.
2) Push open the tailgate from inside by
pushing up on the emergency lever (2)
using a flat blade screwdriver or the jack
handle. The tailgate will be latched again
by closing the tailgate simply.
68LM246
If the tailgate cannot be unlatched by push-
ing the unlatch switch (1), have the vehicle
inspected by your DXWKRULVHG0DUXWL6X]XNL
ZRUNVKRS
.H\OHVV3XVK6WDUW6\VWHP5HPRWH
&RQWUROOHU.H\OHVV(QWU\6\VWHP
7UDQVPLWWHU
64MS022
Your vehicle is equipped with either a key-
less push start system remote controller
(Type A) or a keyless entry system trans-
mitter (Type B). The remote controller has
a keyless entry system and a keyless push
start system. The transmitter has only a
keyless entry system. For details, refer to
the following explanations.
:$ 5 1 , 1 *
$OZD\V PDNH VXUH WKDW WKH WDLOJDWH LV
FORVHG DQG ODWFKHG VHFXUHO\ &RP
SOHWHO\ FORVLQJ WKH WDLOJDWH KHOSV SUH
YHQW RFFXSDQWV IURP EHLQJ WKURZQ
IURP WKH YHKLFOH LQ WKH HYHQW RI DQ
DFFLGHQW &RPSOHWHO\ FORVLQJ LW DOVR
KHOSVNHHSH[KDXVWJDVHVIURPHQWHU
LQJWKHYHKLFOH
&$87,21

Downloaded from www.Manualslib.com manuals search engine 
%()25('5,9,1*
06(
.H\OHVV XQORFNLQJORFNLQJ XVLQJ WKH
UHTXHVWVZLWFKHV
64MS134
When the remote controller is within the
operating range described in this section,
you can lock or unlock the doors (including
the tailgate) by pushing the request switch
(1) on the driver’s door handle, front pas-
senger’s door handle or tailgate.
To lock all doors when all doors are
unlocked:
• To lock all doors, push one of the
request switches once.
The turn signal lights will flash once and
the siren will sound once when the doors
are locked.
To unlock a door or all doors:
• Push one of the request switches once
to unlock only one door.
• Push one of the request switches twice
to unlock all doors.NOTE:
You can switch the function that unlocks all
doors from twice operations to once opera-
tion, and vice versa, via the setting mode
of the information display. For details on
how to use the information display, refer to
“Information Display” in this section.
When the doors are unlocked:
• The turn signal lights will flash twice and
the siren will sound twice.
• If the interior light switch is in the door
position, the interior light will turn on for
about 15 seconds and then fade out. If
you press the engine switch during this
time, the light will start to fade out imme-
diately.
Be sure the doors are locked after you
operate the request switch to lock the
doors.NOTE:
• If you lock the doors using the request
switch when the engine hood is open,
the siren will sound 3 times to remind
you.
• If the security system was triggered due
to an unauthorized entry into the vehicle
and then you unlock the doors using the
request switch, the siren will sound 4
times to remind you. If this happens,
check whether your vehicle has been
broken into while you were away from it.
• You can set whether the siren sounds
when locking or unlocking the door(s) via
the setting mode of the information dis-
play. For details on how to use the infor-
mation display, refer to “Information
Display” in this section.NOTE:• The door locks cannot be operated by
the request switch under the following
conditions:
– If any door is open or is not completely
closed.
– If the ignition mode is other than LOCK
(OFF).
• If no doors are opened within about 30
seconds after unlocking the doors by
pushing the request switch, the doors will
be locked again automatically.
(1)
(;$03/(
NOTICE

Downloaded from www.Manualslib.com manuals search engine %()25('5,9,1*
06(
80J056
(1) 80 cm (2 1/2 feet)
When the remote controller is within
approximately 80 cm (2 1/2 feet) from a
front door handle or the tailgate switch, you
can lock or unlock the doors by pushing
the request switch.
NOTE:
• If the remote controller is outside the
request switch operating range
described above, you will not be able to
operate the request switch.
• If the battery of the remote controller
runs down or there are strong radio
waves or noise, the request switch oper-
ating range may be reduced or the
remote controller may be inoperative.
• If the remote controller is too close to the
door glass, the request switches may not
operate.• If a spare remote controller is in the vehi-
cle, the request switches may not oper-
ate normally.
• The remote controller will only operate a
request switch if it is within the switch’s
operating range. For example, if the
remote controller is within the operating
range of the driver’s door request switch
but not the front passenger’s door
request switch or the tailgate request
switch, the driver’s door switch can be
operated but the front passenger’s door
switch or tailgate switch cannot be oper-
ated.
• Avoid operations of switch with sharp
objects.
NOTE:
The keyless push start system may not
function correctly in certain environments
or under certain operating conditions such
as the following:• When there are strong signals coming
from a television, power station or a cel-
lular phone.
• When the remote controller is in contact
with or covered by a metal object.
• When a radio wave type remote keyless
entry is used nearby.
• When the remote controller is placed
near an electronic device such as per-
sonal computer.
Some additional precautions you should
take and information you should be aware
of are:
• Make sure the key is stowed in the
remote controller. If the remote controller
becomes unreliable, you will not be able
to lock or unlock the doors.
• Be sure that the driver always carries the
remote controller.
•If you lose one of the remote controllers,

ask your
DXWKRULVHG 0DUXWL 6X]XNL
ZRUNVKRSas soon as possible for a
replacement.Be sure to have your
dealer program the

new remote
controller code in your vehi-cle’s
memory so that the old code is

erased.
• You can use up to four remote controllers

and the keys for your vehicle. Ask your

DXWKRULVHG 0DUXWL 6X]XNL ZRUNVKRS
for

details.
• The battery life of the remote controller is
about two years, but it can vary depend-
ing on usage conditions.
(1)
(1)(1)
(;$03/(
NOTICE
7KH UHPRWH FRQWUROOHU LV D VHQVLWLYH
HOHFWURQLF LQVWUXPHQW 7R DYRLG GDP
DJLQJWKHUHPRWHFRQWUROOHU

Downloaded from www.Manualslib.com manuals search engine 
%()25('5,9,1*
06(
57L21016
To stow the key into the remote controller,
push the key in the remote controller until
you hear a click.
68LM247
To remove the key from the remote control-
ler, push the button (A) in the direction of
the arrow and pull the key out from the
remote controller.5HTXHVWVZLWFKZDUQLQJEX]]HU
This exterior buzzer beeps for about 2 sec-
onds in the following conditions to warn you
that the request switch is not working:
• The request switch is pressed after all
doors are closed with the ignition mode
changed to “ACC” or “ON” by pressing
the engine switch.
• The request switch is pressed in any of
the following conditions after changing
the ignition mode to “LOCK” (OFF) by
pressing the engine switch.
– The remote controller is left inside the
vehicle.
– Any door (including the tailgate) is
open.
Press the request switch again after doing
the following:
With the ignition mode changed to “LOCK”
(OFF) by pressing the engine switch, bring
out the remote controller if it is inside the
vehicle and check that all doors are com-
pletely closed.
5HPLQGHUIXQFWLRQ
64MS165
If the remote controller is not in the vehicle
under the following conditions, the buzzer
sounds intermittently for about 2 seconds
and the immobilizer/keyless push start sys-
tem warning light on the instrument cluster
blinks:When one or more doors are opened and
all of the doors are later closed with the
ignition mode is other than “LOCK”.
The indicator light will turn off within sev-
eral seconds after the remote controller is
returned to an area of the vehicle other
than the rear luggage area.
If the remote controller is left in the vehicle
and you lock the driver’s door or front pas-
senger’s door as described below, the door
will be automatically unlocked.
• If you open the driver’s door and lock the
door by turning the lock knob forward or
pushing the power door locking switch,
(A)
(;$03/(

Downloaded from www.Manualslib.com manuals search engine 
%()25('5,9,1*
06(
NOTE:
Used batteries must be disposed properly
according to applicable rules or regulations
and must not be disposed with ordinary
household trash.
.H\OHVV(QWU\6\VWHP7UDQVPLWWHU
7\SH%
76MS011
(1) “Lock” button
(2) “Unlock” button
You can lock or unlock all doors (including
the tailgate) simultaneously by operating
the transmitter near the vehicle.&HQWUDOGRRUORFNLQJV\VWHP
• To lock all doors, push the “LOCK” but-
ton (1) once.
• To unlock only the driver’s door, push the
“UNLOCK” button (2) once.
• To unlock other doors, push the
“UNLOCK” button (2) once again.
NOTE:
You can switch the function that unlocks all
doors from twice operations to once opera-
tion, and vice versa, via the setting mode
of the information display. For details on
how to use the information display, refer to
“Information Display” in this section.
The turn signal lights will flash once and
the siren (if your vehicle is equipped with
the security system) will sound once when
the doors are locked.
When the doors are unlocked:
• The turn signal lights will flash twice and
the siren (if your vehicle is equipped with
the security system) will sound twice.
• If the interior light switch is in the
“DOOR” position, the interior light will
turn on for about 15 seconds and then
fade out. If you insert the key into the
ignition switch during this time, the light
will start to fade out immediately.
Be sure the doors are locked after you
operate the lock button (1).
NOTICE
7KH UHPRWH FRQWUROOHU LV D VHQVLWLYH
HOHFWURQLF LQVWUXPHQW 7R DYRLG GDP
DJLQJ LW GR QRW H[SRVH LW WR GXVW RU
PRLVWXUHRUWDPSHUZLWKLQWHUQDOSDUWV
(1)
(2)

Downloaded from www.Manualslib.com manuals search engine %()25('5,9,1*
06(
6HFXULW\6\VWHPLIHTXLSSHGThe security system is armed in about 5
seconds after you lock all doors (including
the tailgate) by using the keyless entry sys-
tem transmitter, keyless push start system
remote controller or request switch.
Once the system is armed, any attempt to
open a door by using any other means (*)
than the keyless entry system transmitter,
keyless push start system remote control-
ler or request switch, or open the engine
hood, will cause the alarm to be triggered.
* These means include the following:
– The key
– The lock knob on a door
– The central door locking switchAlso, in case that you have set the shock
sensor to enabled state and set sensitivity
of the pre-warning function and full blast
warning function to a level other than 0, the
alarm will be triggered if any attempt is
made to tamper with the vehicle. The shock
sensor can be selected to enabled or dis-
abled state, and sensitivity of each warning
can be adjusted as desired. To set the
shock sensor, ask your DXWKRULVHG 0DUXWL
6X]XNLZRUNVKRSor use the setting mode of
theinformation display.NOTE:
• The default setting of the shock sensor
is in the disabled state. Set to the
enabled state and adjust sensitivity of
each warning according to your prefer-
ence. For details on how to use the infor-mation display, refer to “Information
Display” in this section.
• Your dealer may have already set the
shock sensor of the vehicle to the
enabled state before you purchase it.
Consult your dealer for further informa-
tion.
NOTE:
• The security system generates alarms
when any of the predetermined condi-
tions is met. However, the system does
not have any function of blocking unau-
thorized entry into the vehicle.
• Always use the keyless entry system
transmitter, keyless push start system
remote controller or request switch to
unlock the doors when the security sys-
tem has been armed. Using a key
instead will trigger the alarm.
• If a person who does not know the secu-
rity system is going to drive the vehicle,
we recommend you explain the system
and its operation to the person, or dis-
able the system beforehand. Mistakenly
triggering the alarm may cause a nui-
sance to others.
• Even if the security system is armed,
you should still be careful to guard
against theft. Do not leave money or
things of value in the vehicle.+RZWRDUPWKHVHFXULW\V\VWHP
ZKHQHQDEOHG
Lock all doors (including the tailgate) using
the keyless entry system transmitter, key-
less push start system remote controller or
request switch. The security system indica-
tor (1) will start blinking rapidly, and the
security system will be armed in about 5
seconds.
While the system is being armed, the indi-
cator continues to blink at intervals of
approximately 2 seconds
61MM0A134
NOTE:
• To prevent the alarm from being acci-
dentally triggered, avoid arming it while
anyone remains inside the vehicle. The
alarm will be triggered if any person
inside opens the door or engine hood, or
swings the vehicle (if the shock sensor is
in the enabled state).
• The security system is not armed when
all doors are locked using the key from
(1)

Downloaded from www.Manualslib.com manuals search engine 
%()25('5,9,1*
06(
:DUQLQJDQGLQGLFDWRUPHVVDJHV
:DUQLQJDQG,QGLFDWRU
0HVVDJH0DVWHU:DUQLQJ
,QGLFDWRU/LJKW6RXQG &DXVHDQG5HPHG\
61MM0A162
Blinks
(only while vehicle is in motion)
Beep (one time from interior buzzer; only while vehicle is in motion)
A door or tailgate is not properly closed. Stop in a safe place and close the door or tailgate properly.
(#1)
64MS182

Downloaded from www.Manualslib.com manuals search engine %()25('5,9,1*
06(
2SHQ'RRU:DUQLQJ/LJKW
54G391
This light remains on until all doors (includ-
ing the tailgate) are completely closed.
If any door (including the tailgate) is open
when the vehicle is moving, a ding sounds
to remind you to close all doors completely.
/RZ)XHO:DUQLQJ/LJKW
54G343
If this light comes on, fill the fuel tank
immediately.
When this light comes on, a ding sounds
once to remind you to fill the fuel.
If you do not fill the fuel, a ding sounds
every time when the ignition switch is
turned to the “ON” position or the engine
switch is pressed to change the ignition
mode to ON.
NOTE:
The activation point of this light varies
depending on road conditions (for exam-
ple, slope or curve) and driving conditions
because of fuel moving in the tank.
(OHFWULF3RZHU6WHHULQJ/LJKW
79J039
This light comes on when the ignition
switch is turned to the “ON” position or the
engine switch is pressed to change the
ignition mode to ON, and goes out when
the engine is started.
If this light comes on or blinks while driv-
ing, the power steering system may not
work properly. Have the system inspected
by your DXWKRULVHG 0DUXWL 6X]XNL
ZRUNVKRS
NOTE:
While parking or driving at very low speed
greater steering effort is required. This is
not a malfunction of the steering system
but power steering control system limiting
power assist in order to prevent it from
over heating.
• The steering wheel is operated very
often.
• The steering wheel is kept in a fully
turned position for a long while.
When the power steering control system
cools down, the power steering system is
restored back to the original condition.

Downloaded from www.Manualslib.com manuals search engine 23(5$7,1*<2859(+,&/(
06(
(QJLQH6ZLWFK
9HKLFOHZLWK.H\OHVV3XVK
6WDUW6\VWHP
61MM0B001
/2&.2))
Once this mode is selected by pressing the
engine switch, opening or closing of any
door (including the tailgate) will result in
automatic locking or steering.
$&&
Press the engine switch to select this igni-
tion mode to use such electric equipment
as the audio system, outside rearview mir-
rors and accessory socket with the engine
off. When this position is selected, the
information display in the instrument clus-
ter shows the following message: “ACC”
IGNITION SWITCH POSITION. Refer to
“Information Display” in the ³%()25(
'5,9,1*´ section for details.
21