check oil SUZUKI SWIFT 2000 1.G SF310 Service Manual PDF

ENGINE AND EMISSION CONTROL SYSTEM (TBI FOR G10) 6E1-27
1) Connect scan tool to DLC with ignition switch OFF, if it is avail-
able.
2) Warm up engine to normal operating temperature.
3) Select “Data List” mode on scan tool to check “IAC duty”.
4) Apply load to engine as described below and check that idle
speed is kept at specified level and “IAC duty” increases as spe-
cified below. At the same time, check that plunger of ISC actua-
tor moves.
Increase of ISC duty
when headlight turns ON : About 3.5%
when A / C is operating : About 10%
5) Stop engine and leave it as it is till it cools off. Then check that
plunger of ISC actuator moves when ignition switch is turned
from OFF to ON once.
If abnormality is found in Steps 4) and 5), check ISC relay, ISC
actuator, ISC electric circuit and closed throttle position switch
signal.
If abnormality is found in Step 4) only, check A/C signal circuit
or power steering pressure switch signal circuit first.
ISC ACTUATOR
NOTE:
As ISC actuator has been preadjusted precisely at factory, it must
not be taken out of throttle body or disassembled.
INSPECTION
1) Disconnect connector from ISC actuator.
2) Check whether ISC actuator coil is open or short.
ISC actuator resistance at 20C (68F): 3 – 50 Ω
NOTE:
Above data should be used as reference value for determin-
ing whether coil is open or short only. ISC actuator resis-
tance may be out of above specified range even when ISC
actuator is normal.

ENGINE AND EMISSION CONTROL SYSTEM (SFI FOR G13) 6E2-15
CAUTION:
Do not disassemble IAC
valve. Disassembly spoils
its original performanceCAUTION:
Do not remove or adjust
throttle stop screw as it is
factory adjusted precisely
1. Throttle body
2. Throttle stop screw
3. TP sensor
4. O-ring
5. Idle air control valve
6. IAC valve screws : Tightening torque
: Do not reuse
AIR INTAKE SYSTEM
THROTTLE BODY
On-Vehicle Inspection

Check that throttle valve lever (1) moves smoothly.
Removal
1) Disconnect negative cable at battery.
2) Drain cooling system.
3) Disconnect accelerator cable (1) from throttle body.
4) Disconnect air cleaner outlet hose (1) from throttle body.

6E2-22 ENGINE AND EMISSION CONTROL SYSTEM (SFI FOR G13)
FUEL PRESSURE REGULATOR
Removal
1) Relieve fuel pressure according to procedure described in sec-
tion 6.
2) Disconnect battery negative cable at battery.
3) Disconnect vacuum hose (3) from fuel pressure regulator (1).
4) Disconnect fuel return hose (2) from fuel pressure regulator (1).
CAUTION:
A small amount of fuel may be released when hose is dis-
connected. Cover hose to be disconnected with a shop
cloth.
5) Remove fuel pressure regulator.
CAUTION:
A small amount of fuel may be released when it is from
delivery pipe.
Place a shop cloth under delivery pipe so that released
fuel is absorbed in it.
Installation
For installation, reverse removal procedure and note following pre-
cautions.

Use new O-ring.

Apply thin coat of spindle oil or gasoline to O-ring to facilitate
installation.

With engine OFF and ignition switch ON, check for fuel leaks
around fuel line connection.
Tightening Torque
Fuel pressure regulator bolt: 11 N
.m (1.1 kg-m, 8.0 lb-ft)

(a)
6E2-32 ENGINE AND EMISSION CONTROL SYSTEM (SFI FOR G13)
CAMSHAFT POSITION SENSOR
Inspection
Check camshaft position sensor referring to DTC P0340 Diag. Flow
Table in Section 6. If malfunction is found, replace.
Removal
1) Disconnect negative cable at battery.
2) Disconnect connector from camshaft position sensor.
3) Remove camshaft position sensor from sensor case
(distributorless ignition case).
Installation
1) Check that O-ring is free from damage.
2) Check that camshaft position sensor and signal rotor tooth are
free from any metal particles and damage.
3) Install camshaft position sensor to sensor case.
Tightening Torque
(a): 9 N
.m (0.9 kg-m, 6.5 lb-ft)
4) Connect connector to it securely.
5) Connect negative cable to battery.
CRANKSHAFT POSITION SENSOR
Inspection
Check crankshaft position sensor referring to step 1 and 2 of DTC
P0335 Flow Table. If malfunction is found, replace.
Removal
1) Hoist vehicle.
2) Disconnect connector from crankshaft position sensor.
3) Remove crankshaft position sensor from oil pan.
Installation
1) Check to make sure that crankshaft position sensor and pulley
tooth is free from any metal particles and damage.
2) Install crankshaft position sensor to oil pan.
Tightening Torque
(a): 10 N
.m (1.0 kg-m, 7.5 lb-ft)
CAUTION:
Be sure to tighten to specified torque. CKP sensor will be
deformed if overtightened and correct CKP sensor signal
will not be fed if loosened.
3) Connect connector to it securely.

IGNITION SYSTEM 6F-3
DIAGNOSIS
ConditionPossible CauseCorrection
Engine cranks, but will
not start or hard to start
Blown fuse for ignition coil

Loose connection or disconnection of lead wire or
high-tension cord(s)

Faulty high-tension cord(s)

Faulty spark plug(s)

Cracked rotor or cap

Maladjusted signal rotor air gap

Faulty ignition coil

Faulty noise suppressor

Faulty CMP sensor

Faulty igniter

Faulty ECM (or PCM)

Maladjusted ignition timingReplace
Connect securely
Replace
Adjust, clean or replace
Replace
Adjust
Replace
Replace
Replace
Replace
Replace
Adjust
Poor fuel economy or
engine performance
Incorrect ignition timing

Faulty spark plug(s) or high-tension cord(s)

Faulty ECM (or PCM)Adjust
Adjust, clean or replace
Replace
DIAGNOSTIC FLOW TABLE
STEPACTIONYESNO
1Was “Engine Diagnostic Flow Table” in SECTION 6
performed?Go to Step 2.Go to “Engine
Diagnostic Flow
Table” in SECTION 6.
2Ignition Spark Test
1) Check all spark plug for condition and type,
referring to “Spark Plugs” in this section.
2) If OK, perform ignition spark test, referring to
“Ignition Spark Check” in this section.
Is spark emitted from all spark plugs?Go to Step 11 on the
next page.Go to Step 3.
3Diagnostic Trouble Code (DTC) Check
1) Check DTC stored in ECM (or PCM), referring to
“Diagnostic Trouble Code (DTC) Check” in
SECTION 6.
Is DTC stored?Go to applicable flow
table corresponding to
that code No. in
SECTION 6.Go to Step 4.
4Electrical Connection and Noise Suppressor Check
1) Check ignition coil for electrical connection and
noise suppressor for conductivity.
Are they good condition?Go to Step 5.Repair or replace.
5High-tension Cord Check
1) Check high-tension cord for resistance, referring
to “High-tension Cords” in this section.
Is check result satisfactory?Go to Step 6.Replace high-tension
cord(s).

6F-4 IGNITION SYSTEM
STEPACTIONYESNO
6Ignition Coil Power Supply and Ground Circuit
Check
1) Check ignition coil power supply (“B/W” wire)
circuit for open and short.
Are circuits in good condition?Go to Step 7.Repair or replace.
7Ignition Coil Check
1) Check ignition coil for resistance, referring to
“Ignition Coil” in this section.
Is check result satisfactory?Go to Step 8.Replace ignition coil
assembly.
8CMP Sensor Check
1) Check CMP sensor and signal rotor, referring to
“Distributor Unit” in this section.
Is check result satisfactory?Go to Step 9 on the
next page.Adjust or replace.
9Ignition Trigger Signal Circuit Check
1) Check ignition trigger signal (“Br / Y” or “Or” wire)
circuit for open, short and poor connection.
Are circuits in good condition?Go to Step 10.Repair or replace.
10Igniter Check
1) Check igniter, referring to “Igniter” in this section.
Is check result satisfactory?Go to Step 11.Replace igniter.
11Ignition Timing Check
1) Check initial ignition timing and ignition timing
advance, referring to “Ignition Timing” in this
section.
Is check result satisfactory?Substitute a known-
good ECM (or PCM)
and then repeat
Step 2.Go to Step 12.
12Ignition Timing Adjustment and Recheck
1) Adjust initial ignition timing, referring to “Ignition
Timing” in this section.
2) Recheck initial ignition timing and ignition timing
advance, referring to “Ignition Timing” in this
section.
Is check result satisfactory?System is in good
condition.Substitute a known-
good ECM (or PCM)
and then repeat
Step 2.

1. Injector coupler
2. Throttle body
3. Air cleaner case
4. Cylinder head cover
1. High-tension code 2. Cap
1. High-tension
cord
2. Ohmmeter
IGNITION SYSTEM 6F-5
ON-VEHICLE SERVICE
IGNITION SPARK TEST
1) Disconnect injector coupler at throttle body side.
WARNING:
Without disconnection of injector coupler, combustible gas
may come out from spark plug holes during this test and
may get ignited in engine room.
2) Remove spark plugs and connect them to high-tension cords,
and then ground spark plugs.
3) Crank engine and check if each spark plug sparks.
4) If no spark is emitted, inspect high-tension cords, spark plugs,
ignition coil, distributor, etc.
HIGH-TENSION CORDS
1) Remove high-tension cord at ignition coil while gripping its cap.
2) Remove distributor cap installed with high-tension cords.
3) Remove high-tension cord clamp from cylinder head cover.
4) Pull out high-tension cords from spark plugs while gripping each
cap.
CAUTION:

Removal of high-tension cords together with clamps
will be recommended so as not to damage their inside
wire (resistive conductor).

For the same reason, pull out each connection by grip-
ping cap portion.
5) Measure resistance of high-tension cord by using ohmmeter.
High-tension cord resistance: 10 – 22 kΩ/ m (3.0 – 6.7 kΩ/ft)

PRIMARY
SECONDARY
1. Ohmmeter
IGNITION SYSTEM 6F-7
IGNITION COIL
1) Pull out high-tension cord by gripping its cap.
2) Disconnect ignition coil coupler.
3) Measure primary and secondary coil resistances.
Ignition coil resistance (at 20C, 68F)
Primary : 0.87 – 1.05 Ω
Secondary : 11.2 – 15.2 kΩ
4) If resistance is out of specification, replace coil with new one.
IGNITER
Before this inspection, prepare 5 V power supply (3 new 1.5 V bat-
teries), one 12 V 3.4 W light bulb and one 12 V battery (fully
charged).
1) Disconnect igniter coupler (1).
2) Remove igniter (2) from its bracket.
3) Arrange 3 new batteries in series (1) (check total voltage is about
4.7 V).
4) Connect light bulb (2) between “c” terminal of igniter (3) and bat-
tery (4) positive (+) terminal, then connect battery negative (–)
terminal to igniter body.
Also connect battery positive (+) terminal and “b” terminal of ig-
niter.
Check that the light bulb does not illuminate.
5) Connect negative (–) terminal of batteries (1) and igniter body.
Check that the light bulb illuminate when positive (+) terminal of
batteries (1) is connected to “a” terminal of igniter.
If inspection result is not satisfactory, replace igniter.
6) Install igniter and connect igniter coupler.

1. Pickup coil
2. Signal rotor
3. Screws
1. Distributor
2. Coupler
3. Ohmmeter
6F-8 IGNITION SYSTEM
DISTRIBUTOR
DISTRIBUTOR CAP AND ROTOR
INSPECTION
Check cap and rotor for crack and their terminals for corrosion and
wear. Replace as necessary.
SIGNAL ROTOR AIR GAP
INSPECTION
1) Remove distributor cap and rotor.
2) Using thickness gauge, measure air gap, between signal rotor
tooth and CMP sensor (generator).
Signal rotor air gap “a”: About 0.2 mm (about 0.008 in.)
3) If gap is out of specification, loose CMP sensor (signal genera-
tor) securing screws. Using blade (–) screw driver, move CMP
sensor (generator) and adjust gap to specification. After adjust-
ment, tighten securing screws and recheck gap.
NOTE:
Check to make sure that CMP sensor (signal generator)
tooth is free from any metal particles.
4) Install distributor cap and rotor.
CMP SENSOR (PICKUP COIL) RESISTANCE
INSPECTION
1) Disconnect distributor lead coupler.
2) Measure resistance of pickup coil by using ohmmeter.
3) If resistance is out of specification, replace CMP sensor (signal
generator) as follows.
Pickup coil resistance:
185 – 275 Ω at – 10C (14F) – 50C (122F)
240 – 325 Ω at 50C (122F) – 100C (212F)
4) Remove distributor cap and rotor.
5) Remove CMP sensor (signal generator) securing screws and
lead wire clamp screws.
6) Replace CMP sensor (signal generator).
7) Adjust signal rotor air gap to specifications as previously out-
lined.
8) Install rotor, distributor cap seal and cap.

1. Cap
2. Cap seal
3. Cap screw
4. Rotor
5. CMP sensor
(Signal generator)
6. Screw
7. Cover
8. Housing
9. O-ring
A: Slot offset
1. Distributor case
2. O-ring3. Distributor coupling
4. Camshaft
6F-10 IGNITION SYSTEM
DISTRIBUTOR UNIT
DISMOUNTING
1) Disconnect distributor lead coupler.
2) Remove distributor cap screws and cap.
3) Remove distributor flange bolts.
4) Pull out distributor housing assembly.
REMOUNTING
NOTE:

Before installing distributor, check to make sure that its
O-ring is in good condition.

If new O-ring is installed, apply oil.
1) Install distributor without cap to camshaft.
Fit the dogs of distributor coupling into the slots of camshaft,
when installing. The dogs of distributor coupling are offset.
Therefore, if the dogs can not shaft by 180 degree and try again.
2) Lightly install flange bolts and prepare for ignition timing adjust-
ment.
3) Check to make sure that rotor is in good condition.
4) Inspect distributor cap and clean or replace as required.
5) Make sure that distributor cap seal is placed properly and install
cap, and then fasten it with screws.
6) Connect distributor lead coupler.
7) Check and adjust ignition timing as previously outlined.