ECO mode TOYOTA 4RUNNER 2003 N210 / 4.G Navigation Manual

4Runner_Navi_U (L/O 0208)
1312003 MY 4Runner Navigation from Aug. ’02 Prod. (OM35799U)
(b) Tone and balance
How good an audio program sounds to you
is largely determined by the mix of the
treble, midrange, and bass levels. In fact,
different kinds of music and vocal programs
usually sound better with different mixes of
treble, mid −range and bass.
A good balance of the left and right stereo
channels and of the front and rear sound
levels is also important.
Keep in mind that if you are listening to a
stereo recording or broadcast, changing the
right/left balance will increase the volume of
one group of sounds while decreasing the
volume of another.
NZN030
Touching the “SOUND” switch dis-
played on the screen at the audio con-
trol mode will display the sound con-
trol mode. Adjust the tone and balance
as follows.
To adjust the tone, touch the “+” or
“” switches on the screen. To adjust
the balance between the front and rear
speakers, touch the “Front” or “Rear”
switch on the screen, and to adjust
the balance between the left and right,
touch the “L” or “R” switch on the
screen.
BASS: Adjusts low− pitched tones.
MID: Adjusts mid −pitched tones.
TREB: Adjusts high− pitched tones.
As the orange display goes up, each tone is
more emphasized. (c) Surround function
Touching the “SURROUND” switch dis-
played on the screen at the audio con-
trol mode will turn on or off the sur-
round function.

4Runner_Navi_U (L/O 0208)
1342003 MY 4Runner Navigation from Aug. ’02 Prod. (OM35799U)
(b) Presetting a station1. Tune in the desired station.
2. Touch one of the station selector switch es (16) and hold it until a beep is heard. This sets the station to the switch
and the frequency appears on the switch
Each radio mode (AM, FM1 or FM2) can
store up to 6 stations. To change the
preset station to a different one, follow
the same procedure.
The preset station memory is cancelled
when the power source is interrupted by
battery disconnection or a blown fuse. (c) Selecting a station
Tune in the desired station using one of
the following methods.
Preset tuning: Touch the switch (1
−6) for
the station you want. The switch is high-
lighted in green an d the station frequency
appears on the screen.
Seek tuning: Push the “SEEK/TRACK”
button on either side. The radio will begin
seeking up or down for a station of the
nearest frequency and will stop on recep-
tion. Each time you push the button, the
stations will be searched out one after
another. To scan all the frequencies:
Touch the
“SCAN” switch on the screen or push the
“SCAN” button briefly. “SCAN” appears on
the screen. The radio will find the next
station and stay ther e for a few seconds,
and then scan again. To select a station,
touch the “SCAN” switch or push the
“SCAN” button again.

4Runner_Navi_U (L/O 0208)
1352003 MY 4Runner Navigation from Aug. ’02 Prod. (OM35799U)
To scan the preset stations: Touch the
“SCAN” switch on the screen or push the
“SCAN” button for longer than 2 seconds.
“P. SCAN” appears on the screen. The
radio will tune in the next preset station,
stay there for a few seconds, and then
move to the next preset station. To select
a station, touch the “SCAN” switch or
push the “SCAN” button again.
(d) Radio Data System
Your audio system is equipped with Radio
Data Systems (RDS). RDS mode pro-
vides you to receive text messages from
radio stations that utilize RDS transmit-
ters.
When RDS is on, the radio can
—only select stations of a particular pro-
gram type,
—display messages from radio stations,
—search for a stronger signal station,
—search for local stations broadcasting
the same network as the vehicle travels,
—receive announcements concerning lo-
cal and national emergencies (even if
RDS function is turned off).
RDS features are available for the use
only on FM stations which broadcast RDS
information. “RDS SRCH” (RDS search) switch
This switch allows you to search all avail-
able RDS stations out of the entire FM
band and sort them by program type
(See following “TYPE” switch for details
on program types).
By touching this button at the FM mode,
RDS is turned on and the radio is
switched to FM type mode. During the
program type search, “RDS SEARCH” will
be shown on the screen. Also at this
time, “FM TYPE” will appear on the
screen to indicate that the station selec-
tor switches are for program type.
After searching for all the available RDS
stations, the radio will activate the pre-
viously used program type. If the pre-
viously used program type is not avail-
able, or if the radio has not yet
performed a program type search, the
radio will activate the first available pro-
gram type that has stations in memory.
The radio will preset the stations of the
current program type into the preset but-
tons.
These are accessible through the “TYPE”
switch. If more than 6 stations are found,
the radio will load the 6 strongest sta-
tions signal of the program type into the
presets.

4Runner_Navi_U (L/O 0208)
1392003 MY 4Runner Navigation from Aug. ’02 Prod. (OM35799U)
L00177
Push the “TAPE” button if a cassette
tape is already in the slot.
Dolby Noise Reduction
∗ feature: If you
are listening to a tape that was recorded
with Dolby
∗ Noise Reduction, touch the
“
” switch on the screen. The symbol
is highlighted in green.
The Dolby NR mode reduces tape noise by
about 10 dB. For best sound reproduction,
play your tapes with the Dolby NR on or off
according to the mode used for recording the
tape.
To play a tape recorded without Dolby NR,
touch the switch once again.
∗: Dolby noise reduction manufactured under license from
Dolby Laboratories Licensing Corporation. “DOLBY” and the
double D symbol
are trademarks of Dolby Laboratories
Licensing Corporation.
(b) Manual program selection
Program switch: Touch the “
”
switch on the screen to select the other
side of a cassette tape. The display indi-
cates which side is currently selected ( \b
indicates top side, indicates bottom
side).
Fast forward switch: Touch the “”
switch on the screen to fast forward a
cassette tape. “FF” appears on the
screen.
To stop fast forwarding, touch the same
switch or push the “TAPE” button.
Rewind switch: Touch the “” switch
on the lower side to rewind a tape.
“REW” appears on the screen.
To stop rewinding, touch the same switch
or push the “TAPE” button.
Autoreverse feature: After the cassette
player reaches the end of a tape, it auto-
matically reverses and begins to play the
other side, regardless of whether the cas-
sette was playing or fast forwarding.

4Runner_Navi_U (L/O 0208)
1542003 MY 4Runner Navigation from Aug. ’02 Prod. (OM35799U)
1. Playing a DVD video disc
Touch the number of the disc you
want to play. The selected disc is au-
tomatically played.
When you touch the “PICTURE” switch,
the video screen appears.
For safety reasons, you can enjoy DVD
video discs only when the vehicle is com-
pletely stopped with the ignition switch in
the “ACC” or “ON” position and the park-
ing brake applied. While you are driving,
you can hear audio alone even in the
DVD video mode.
NZN016
NZN017
2. Displaying op eration switches
If you touch a part of the screen where
switches are not located while you are
watching video, DVD video operation
switches will appear. “Second Page” switch:
Use this switch
to display the operation switches on the
second page.
“Top Page” switch: Use this switch to
display the operation switches on the top
page. “Hide Keys” switch:
Use this switch to
turn off the operation switches from the
display.
If “
” appears on the display when you
touch a switch, the operation relevant to
the switch is not permitted.

4Runner_Navi_U (L/O 0208)
1662003 MY 4Runner Navigation from Aug. ’02 Prod. (OM35799U)
“Second Page” switch: Use this switch
to display the operation switches on the
second page.
“Top Page” switch: Use this switch to
display the operation switches on the top
page.
“Hide Keys” switch: Use this switch to
turn off the operation switches from the
display.
If “
” appears on the display when you
touch the switch, the operation is not per-
mitted. 3. Description of each switch
SWITCHES ON TOP PAGE
“D. Menu Next” switch: When you touch
this switch while the disc menu is dis-
played, the next page appears on the
display. If you touch this switch while the
player is playing video, the next track is
searched and played.
“D. Menu Prev.” switch: When you
touch this switch while the disc menu is
displayed, the previous page appears on
the screen. If you touch this switch while
the player is playing video, the previous
track is searched and played. “Sel. Number” switch:
The track or
number search screen appears. (See “4.
Searching by track”.)
“Main/Sub” switch: A multiplex transmis-
sion changing switch. The mode changes
from Main/Sub to Main, to Sub and back
to Main/Sub when you touch this switch.
“
” switch: The video CD menu ap-
pears. (For the operation, see the instruc-
tion manual that came with the video
CD.)
SWITCHES ON SECOND PAGE “
” switch:
Use this switch to pause
the video screen. When you touch this
switch again, the video screen advances
frame by frame.
“ ” switch: Touch this switch to resume
normal play after pause.
“ ” switch: Touch this switch to fast
reverse during playback.
“ ” switch: Touch this switch to fast
forward during playback and play slowly
during pause.
“PBC” switch: Use this switch to turn off
playback control.