TOYOTA AVENSIS 1999 Supplement

H11626
Pillar Garnish
Cover
2 Clips
– SUPPLEMENTAL RESTRAINT SYSTEMCURTAIN SHIELD AIRBAG ASSEMBLY
RS–33
4. INSTALL FRONT PILLAR GARNISH
(a) Install the front pillar garnish.
(b) Install the pillar garnish cover with the bolt.
NOTICE:
Be sure to tighten the bolt.
(c) Fell the pillar garnish cover.

RS0IX–01
H03424: Specified torqueN·m (kgf·cm, ft·lbf)Side and Curtain Shield Airbag Sensor Assembly
21 (210, 15)
Front Seat Outer Belt Retractor
5.0 (51, 44 in.·lbf)
42 (430, 31)
Center Piller Garnish
Rear Door Scuff Plate
Front Door Scuff Plate
RS–34– SUPPLEMENTAL RESTRAINT SYSTEMSIDE AND CURTAIN SHIELD AIRBAG SENSOR
ASSEMBLY
SIDE AND CURTAIN SHIELD AIRBAG SENSOR ASSEMBLY
COMPONENTS

RS0IY–01
H03674
H03425
– SUPPLEMENTAL RESTRAINT SYSTEMSIDE AND CURTAIN SHIELD AIRBAG SENSOR
ASSEMBLYRS–35
REMOVAL
NOTICE:
Do not open the cover or the case of the ECU and various
electrical devices unless absolutely necessary.
(If the IC terminals are touched, the IC may be destroyed by
static electricity.)
1. REMOVE FRONT AND REAR SCUFF PLATE
2. REMOVE CENTER PILLAR LOWER GARNISH
3. REMOVE FRONT SEAT OUTER BELT RETRACTOR
(See Pub. No. RM599E on page BO–151)
(a) Disconnect the pretensioner connector.
(b) Remove the 2 bolts and retractor.
4. REMOVE SIDE AND CURTAIN SHIELD AIRBAG SEN-
SOR ASSEMBLY
(a) Disconnect the connector.
NOTICE:
Remove the connector with the sensor assembly installed.
(b) Remove the 2 bolts, nut and side and curtain shield airbag
sensor assembly.

RS0IZ–01
RS–36– SUPPLEMENTAL RESTRAINT SYSTEMSIDE AND CURTAIN SHIELD AIRBAG SENSOR
ASSEMBLY
INSPECTION
1. VEHICLES NOT INVOLVED IN COLLISION
Do a diagnostic system check. (See Pub. No. RM599E on page DI–152)
2. VEHICLES INVOLVED IN COLLISION AND AIRBAG IS NOT DEPLOYED
Do a diagnostic system check. (See Pub. No. RM599E on page DI–152)
3. VEHICLES INVOLVED IN COLLISION AND AIRBAG IS DEPLOYED
Replace the side and curtain shield airbag sensor assembly. (See page RS–34)

RS0J0–01
– SUPPLEMENTAL RESTRAINT SYSTEMSIDE AND CURTAIN SHIELD AIRBAG SENSOR
ASSEMBLYRS–37
REPLACEMENT
REPLACEMENT REQUIREMENTS
In the following cases, replace the side ans curtain shield airbag sensor assembly.

If the side airbag assembly and curtain shield airbag assembly has been deployed in a collision.

If the side and curtain shield airbag sensor assembly has been found to be faulty in troubleshoot-
ing.

If the side and curtain shield airbag sensor assembly has been dropped.
CAUTION:
For removal and installation of the side and curtin shield airbag sensor assembly, see page RS–35
and RS–38.
Be sure to follow the correct procedure.

RS0J1–01
H03425
H03674
RS–38– SUPPLEMENTAL RESTRAINT SYSTEMSIDE AND CURTAIN SHIELD AIRBAG SENSOR
ASSEMBLY
INSTALLATION
NOTICE:

Never use SRS parts from another vehicle. When re-
placing parts, replace them with new ones.

Never reuse the side and curtain shield airbag sensor
assembly involved in a collision when the airbag has
deployed.

Never repair a sensor in order to reuse it.
1. INSTALL SIDE AND CURTAIN SHILD AIRBAG SEN-
SOR
(a) Install the side and curtain shield airbag assembly with
the 2 bolts and nut.
Torque: 21 N·m (210 kgf·cm, 15 ft·lbf)
(b) Connect the side and curtain shild airbag sensor connec-
tor.
NOTICE:

Installation of the connector is done with the sensor
assembly installed. Make sure the sensor assembly
is installed with the specified torque.

If the sensor assembly has been dropped, or there are
cracks, dents or other defects in the case, bracket or
connector, replace the sensor assembly with a new
one.

When installing the sensor assembly, take care that
the SRS wiring does not interfere with other parts and
is not pinched between other parts.

After installation, shake the sensor assembly to
check that there is no looseness.
2. INSTALL FRONT SEAT OUTER BELT RETRACTOR
(See pub. No. RM599E on page BO–159)
(a) Install the retractor with the 2 bolts.
Torque:
Upper bolt: 5.0 N·m (51 kgf·cm, 44 in.·lbf)
Lower bolt: 42 N·m (430 kgf·cm, 31 ft·lbf)
(b) Connect the pretensioner connecter.
3. INSTALL CENTER PILLAR LOWER GARNISH
4. INSTALL FRONT AND REAR DOOR SCUFF PLATE

RS0J2–01
H11591
Spiral Cable Combination Meter
(Warning Light)
Front Passenger Airbag Assembly
Side Airbag Assembly (RH)
Side and Curtain Shield Airbag
Sensor Assembly (RH)
Seat Belt Pretensioner (RH) Steering Wheel Pad
(with Airbag)
Side and Curtain Shield Airbag
Sensor Assembly (LH)Seat Belt
Pretensioner (LH)
Side Airbag Assembly (LH)
Airbag Sensor Assembly Front Airbag Sensor (RH)
Front Airbag
Sensor (LH)Curtain Shield Airbag Assembly (RH) Curtain Shield Airbag Assembly (LH)
– SUPPLEMENTAL RESTRAINT SYSTEMWIRE HARNESS AND CONNECTOR
RS–39
WIRE HARNESS AND CONNECTOR
LOCATION

RS0J3–01
RS–40
– SUPPLEMENTAL RESTRAINT SYSTEMWIRE HARNESS AND CONNECTOR
INSPECTION
HINT:
The SRS wire harness is integrated with the instrument panel wire harness assembly. The wires for the SRS
wire harness are encased in a yellow corrugated tube and all the connectors in the system are a standard
yellow color.
1. VEHICLES NOT INVOLVED IN COLLISION
Do a diagnostic system check. (See Pub. No. RM599E on page DI–152)
2. VEHICLES INVOLVED IN COLLISION
(a) Do a diagnostic system check. (See Pub. No. RM599E on page DI–152)
(b) Check breaks in all wires of the SRS wire harness, and exposed conductors.
(c) Check to see if the SRS wire harness connectors are cracked or chipped.

RS0J4–01
– SUPPLEMENTAL RESTRAINT SYSTEMWIRE HARNESS AND CONNECTOR
RS–41
REPLACEMENT
In the following cases, replace the wire harness or connector.

If any part of the SRS wire harness or any connector has been found to be faulty in troubleshoot-
ing.

If any part of the SRS wire harness or any connector has been found to be faulty during checking
items. (See page RS–40)
CAUTION:
If the wire harness used in the SRS is damaged, replace the whole wire harness assembly.

BODY ELECTRICAL
FOG LIGHT SYSTEM BE–1. . . . . . . . . . . . . . . . . . . .
COMBINATION METER BE–2. . . . . . . . . . . . . . . . . .
REFER TO AVENSIS/CORONA REPAIR MANUAL FOR
CHASSIS AND BODY (Pub. No. RM599E)
NOTE: The above pages contain only the points which differ
from the above listed manual.