TOYOTA AVENSIS 2003 Service Repair Manual

730EY±02
±
THEFT DETERRENT & DOOR LOCK TRANSMITTER SUB±ASSY MODULE SET DOOR
CONTROL73±21
AVENSIS REPAIR MANUAL (RM1018E)
REGISTRATION
1. REGISTER RECOGNITION CODE
HINT:

Register the recognition code when replacing the door control transmitter or the\
door control receiverr.

The add mode is used to register new recognition codes while still retai\
ning codes already registered.
This mode is used when a new transmitter is added. If the number of regi\
stered codes exceeds 4, the
previously registered codes will be erased in order, starting from the first registered code.

The rewrite mode is used to erase all the previously registered recognition\
codes in order to register
new recognition codes. This mode is used when the transmitter or the door control receiver is ex-
changed for a new one.

The confirmation mode is used to confirm how many recognition codes have al\
ready been registered
before an additional registration of a recognition codes.

The all clear mode is used to erase all the registered codes and disables t\
he wireless door lock func-
tion. This mode is used when the transmitter is lost.

All the following registration procedures must be performed in order con\
tinuously.
http://vnx.su

Within 5 sec.
Within 40 sec.
Continued on next page
1.
2.
3.
4.
5.
6.
Insert key into ignition key cylinder, then pull it out.
Close and open driver side door twice.
Close and open driver side door twice.
Insert key into ignition key cylinder and close all doors.
START
Insert key into ignition key cylinder, then pull it out.
Insert key into ignition key cylinder, then pull it out.
Flow Chart of Recognition Code Registration
Within 40 sec.
Within 40 sec. Make sure that the following conditions are met.



No key in ignition key cylinder.

Driver side door is open (Other doors are closed).


Driver side door is unlocked.
73±22
±
THEFT DETERRENT & DOOR LOCK TRANSMITTER SUB±ASSY MODULE SET DOOR
CONTROL
AVENSIS REPAIR MANUAL (RM1018E)
http://vnx.su

Within 40 sec.
ON
LOCK
ON±LOCK operation: 1 time
Add Mode
Rewrite Mode
ON±LOCK operation: 2 times
Confirmation Mode
ON±LOCK operation: 3 times
All Clear Mode
ON±LOCK operation: 5 times
Number of ON±LOCK operations of ignition switch:
Turn ignition switch from LOCK to ON and back to LOCK at approximately
1 second intervals according to the number of times shown below.
Mode Selection:
If the number of the ON±LOCK operations of the ignition switch
is 0, 4 or 6 or more, there will be no response (power door lock and
unlock operation) to inform which mode has been selected.
Remove key from ignition key cylinder.
8.
7.
Within 3 sec.
T1
T1: Approx. 1 sec.
Continued from previous page
Continued on next page
ON
LOCK T1 T1
ON
LOCK T1 T1
ON
LOCK T1 T1
±
THEFT DETERRENT & DOOR LOCK TRANSMITTER SUB±ASSY MODULE SET DOOR
CONTROL73±23
AVENSIS REPAIR MANUAL (RM1018E)
http://vnx.su

Continued from previous page
Integration relay automatically performs power door LOCK±UNLOCK opera\
tion to inform
which mode has been selected.
Response to selected mode (Power door lock operation):
UNLOCKLOCK
LOCK±UNLOCK operation: 1 time
Add Mode
Rewrite Mode Confirmation Mode
All Clear Mode
T1 T1: Approx. 1 sec.
T1 T1
T2
T2
T1 T1
LOCK±UNLOCK operation: 2 times
LOCK±UNLOCK operation: The number of registered codes (1 ± 5 times)
LOCK±UNLOCK operation: 5 times UNLOCK
LOCK
UNLOCK LOCK
UNLOCK LOCK
Continued on next page
Registration procedures are completed.
HINT:

In the confirmation mode, when LOCK±UNLOCK operation is performed twice,\
the
number of registered recognition codes is 2.

In the confirmation mode, when 0 codes are registered, LOCK±UNLOCK o\
peration
is automatically performed 5 times. T2: Approx. 2 sec.
Confirmation Mode and
All Clear ModeAdd Mode or
Rewrite Mode
Within
3 sec.
Within
40 sec.
1st time 2nd time
73±24±
THEFT DETERRENT & DOOR LOCK TRANSMITTER SUB±ASSY MODULE SET DOOR
CONTROL
AVENSIS REPAIR MANUAL (RM1018E)
http://vnx.su

Continued from previous page
Press either LOCK or UNLOCK switch on transmitter once.
9.
Within 40 sec.
Proceed to flow chart to finish
registration.
Press the same switch again.
LOCK±UNLOCK Occurs Once Registration of recognition code has
been completed.
Response to registration completion:
T1: Approx. 1 sec.
LOCK±UNLOCK Occurs Twice
Registration of recognition code has failed.
10.
LOCK
UNLOCK
T1
LOCK
UNLOCK T1 T1
Within
40 sec.
If other transmitter is to be registered.
Within
3 sec.
Registration of recognition codes (add mode and rewrite mode) is compl\
eted.
Integration relay automatically performs power door LOCK±UNLOCK operation to show
whether registration has been completed correctly or not.
HINT:
4 recognition codes can be registered
at once.
HINT:
If LOCK±UNLOCK operation is performed twice, registration of recognition\
code has
failed. Perform registration procedures by beginning once again.
Within
3 sec.


Open a door.

Insert key into ignition key cylinder.
Perform either of the following.
±
THEFT DETERRENT & DOOR LOCK TRANSMITTER SUB±ASSY MODULE SET DOOR
CONTROL73±25
AVENSIS REPAIR MANUAL (RM1018E)
http://vnx.su

730EU±02
73±14
±
THEFT DETERRENT & DOOR LOCK WIRELESS DOOR LOCK CONTROL SYSTEM
AVENSIS REPAIR MANUAL (RM1018E)
WIRELESS DOOR LOCK CONTROL SYSTEM
PRECAUTION
1. NOTICES WHEN CHECKING
(a) The wireless door lock remote control function operates only when the follo\
wing 3 conditions are met. (1) All the doors are closed.
(2) No key is inserted in the ignition key cylinder.
(3) The power door lock system operates normally.
HINT:
The door UNLOCK and luggage door (back door) UNLOCK functions operate \
even when a door is open.
(b) The wireless door lock remote control operational area differs depending on the situation. (1) The operational area differs depending on the operators and the ways the transmitter is held.
(2) In certain areas, the remote control function will only operate partiall\
y for the operational area
will be reduced due to the vehicle body shape and the influence of the surrounding environment.
(3) Since the transmitter uses faint electric waves, strong electric waves or noise in the frequency used may reduce the operational area or the remote control may not funct\
ion.
(4) When the battery weakens, the operational area is reduced or the remote control may not func-
tion.
HINT:
If the door control transmitter has been left in a place that is exposed t\
o the direct sunlight, such as on the
instrument panel, it may cause the battery to weaken or cause other such\
problems.
http://vnx.su

730EV±02
±
THEFT DETERRENT & DOOR LOCKWIRELESS DOOR LOCK CONTROL SYSTEM
73±15
AVENSIS REPAIR MANUAL (RM1018E)
ON±VEHICLE INSPECTION
1.CHECK WIRELESS DOOR LOCK CONTROL FUNCTIONS
HINT:

The switch described in this text is a switch for transmitting signals (LO\
CK switch, UNLOCK switch and
luggage door (back door) unlock switch) which is built in the door control t\
ransmitter.

All the functions listed below must be checked in comparison with the re\
mote control operational area.
(a)Put the vehicle under the conditions that allow the wireless control fun\
ction to be operated (See PRE-
CAUTION on page 73±14).
(b) Check the basic function. (1) Check whether the LED of the transmitter lights up 3 times when each switch i\
s pressed 3 times.
HINT:
If the LED does not light up when the switch has been pressed 3 times or more, it may have a dead bat\
tery.
(2) Check that all the doors including the luggage door (back door) lock when t\
he LOCK switch ispressed (However, this will not happen when any door is open).
(3) w/ Double locking system: Check that the double locking system is set when the LOCK switch is pressed within 5 seconds
after the above step (However, the double locking system is not applicable to the luggage door
(back door)).
CAUTION:
Never activate the double locking system when there are people in the vehicle, because all the doors
cannot be opened from inside the vehicle with the system on. If you lock\
the doors by accident, push
UNLOCK switch of the door control transmitter. (4) Check that all the doors including the luggage door (back door) unlock when\
the UNLOCK switchis pressed. Also, check that the double locking system is canceled at th\
e same time.
(5) Check that the luggage door (back door) unlocks when the luggage door (bac\
k door) unlock
switch is pressed.
HINT:
The UNLOCK switch and luggage door (back door) unlock switch can unlock t\
he doors even when any door
is open.
(c) Check the chattering prevention function. (1) Check that the corresponding operation occurs only once, and not repeated continuously whilethe switch is held down. However, when the switch is operated repeatedly at 1 second intervals,
check that the corresponding operation is carried out.
(d) Check the automatic locking function. (1) Check that all the doors including the luggage door (back door) lock automatically as long asnone of them have been opened or locked within approx. 30 seconds after they\
are unlocked
by pressing the switch.
(2) Check that the automatic locking function does not operate when any door incl\
uding the luggage
door (back door) has been opened or all of them have been locked within ap\
prox. 30 seconds
after they are unlocked by pressing the switch.
(e) Check the switch operation fail±safe function. (1) Check that the doors can not be locked by the switch while the key is in the \
ignition key cylinder.
However, this does not apply when the system is in the recognition code registra\
tion mode.
(f) Check the repeat function. (1) Check that all the doors attempt to automatically lock once again 1 second af\
ter the LOCK switchhas been pressed while the movement of the driver side door control knob, which is in the un-
locked state, is being restricted.
http://vnx.su

B59092
Wire Harness SideDoor Control Receiver
73±16
±
THEFT DETERRENT & DOOR LOCK WIRELESS DOOR LOCK CONTROL SYSTEM
AVENSIS REPAIR MANUAL (RM1018E)
(g) Check the hazard warning lamps flashing function (answer±back). (1) When the LOCK switch is pressed, check that the hazard warning lamps flash once, simulta-neously with the locking of all the doors.
(2) When the UNLOCK switch is pressed once, check that the hazard warning lamps \
flash twice si- multaneously with the unlocking of all the doors.
(3) When the luggage door (back door) unlock switch is pressed once, check tha\
t the hazard warn- ing lamps flash twice simultaneously with the unlocking of the luggage door\
(back door).
2. CHECK DOOR CONTROL RECEIVER
(a) Disconnect the receiver connector.
(b) Check the voltage and resistance between the terminalsof the wire harness side connector and the body ground.
Standard:
Tester ConnectionConditionSpecified Condition
5 (+B) ± Body groundConstant10 to 14 V
1 (GROUND) ± Body groundConstantBelow 1

If the result is not as specified, there may be a malfunction on the wire \
harness side.
(c) Reconnect the connector and check the voltage between the terminal and b\
ody ground.
Standard:
Tester ConnectionConditionSpecified Condition
2 (RDA) ± Body groundNo key in ignition key cylinder, all doors closed
and each transmitter switch OFF ONBelow 1 V Approx. 6 to 7 V Below 1 V
If the result is not as specified, the receiver may have a malfunction.
http://vnx.su

7408X±01
B66561
Roof Side Garnish Inner RH
Front Pillar Garnish RH
Front Door Opening Trim Weatherstrip RH
Center Pillar Garnish RH
Rear Door Opening Trim Weatherstrip RH
Front Door
Scuff Plate RH
Rear Door Scuff
Plate RH
Cowl Side Trim Board RH
41.2 (420, 30)
Center Pillar Garnish
Lower RH
Front Pillar Garnish LH
Front Door Opening Trim
Weatherstrip LH
Cowl Side Trim Board LH
Front Door Scuff Plate LH
Center Pillar Garnish Lower LH
Rear Door Scuff Plate LH
Center Pillar Garnish LH
Rear Door Opening Trim
Weatherstrip LH
Roof Side Garnish Inner LH
Package Tray
Trim Panel Assy
N
m (kgf
cm ft
lbf): Specified torque
41.2 (420, 30)
74±8
±
SLIDING ROOF/CONVERTIBLE SLIDING ROOF
AVENSIS REPAIR MANUAL (RM1018E)
SLIDING ROOF
COMPONENTS
http://vnx.su

B66562
LH Visor Assy
Visor Holder Roof Headlining Assy
RH Visor Assy
Map Lamp Assy
Room Lamp Assy No. 2
Lens Cover
Assist Grip
Sub±assy
Lens Cover Assist Grip Sub±assy
Assist Grip Sub±assy
Assist Grip Sub±assy
Sedan Models
±
SLIDING ROOF/CONVERTIBLE SLIDING ROOF
74±9
AVENSIS REPAIR MANUAL (RM1018E)
http://vnx.su