TOYOTA CAMRY 1999 Service Repair Manual

SF08O±04
S04504
P03193
Oil
Ohmmeter SF±70
± SFI (1MZ±FE)EXHAUST GAS RECIRCULATION (EGR) GAS
TEMPERATURE SENSOR
1569 Author: Date:
INSPECTION
1. REMOVE THROTTLE BODY (See page SF±39)
2. REMOVE EGR GAS TEMPERATURE SENSOR
3. INSPECT EGR GAS TEMPERATURE SENSOR
Using an ohmmeter, measure the resistance between the ter-
minals.
Resistance:
At 50°C (122°F)64 ± 97 kW
At 100°C (212°F)11 ± 16 kW
At 150°C (302°F)2 ± 4 kW
If the resistance is not as specified, replace the sensor.
4. REINSTALL EGR GAS TEMPERATURE SENSOR
5. REINSTALL THROTTLE BODY (See page SF±41)

S05042
Bank 1 Sensor 1
Bank 2 Sensor 1+B
HTOhmmeter
+B HTOhmmeter
SF08P±04
± SFI (1MZ±FE)HEATED OXYGEN SENSOR (Bank 1,2 Sensor 1)
SF±71
1570 Author: Date:
HEATED OXYGEN SENSOR (Bank
1,2 Sensor 1)
INSPECTION
Except California A/T:
INSPECT HEATER RESISTANCE OF HEATED OXYGEN
SENSORS (Bank 1 Sensor 1, Bank 2 Sensor 1)
(a) Disconnect the oxygen sensor connector.
(b) Using an ohmmeter, measure the resistance between the
terminals +B and HT.
Resistance:
At 20°C (68°F)11 ± 16 W
At 800°C (1,472°F)23 ± 32 W
If the resistance is not as specified, replace the sensor.
Torque: 44 N´m (450 kgf´cm, 32 ft´lbf)
(c) Reconnect the oxygen sensor connector.

S05163
Ohmmeter
+B
HTSF08Q±03
SF±72
± SFI (1MZ±FE)HEATED OXYGEN SENSOR (Bank 1 Sensor 2)
1571 Author: Date:
HEATED OXYGEN SENSOR (Bank
1 Sensor 2)
INSPECTION
INSPECT HEATER RESISTANCE OF HEATED OXYGEN
SENSOR (Bank 1 Sensor 2)
(a) Remove the driver's seat.
(b) Take out the floor carpet.
(c) Disconnect the oxygen sensor connector.
(d) Using an ohmmeter, measure the resistance between the
terminals +B and HT.
Resistance:
At 20°C (68°F)11 ± 16 W
At 800°C (1,472°F)23 ± 32 W
If the resistance is not as specified, replace the sensor.
(e) Reconnect the oxygen sensor connector.
Torque: 44 N´m (450 kgf´cm, 32 ft´lbf)
(f) Reinstall the floor carpet.
(g) Reinstall the driver's seat.

SF08R±03
S05450
ECM
ECM Connector
No.2 Instrument
Lower Panel
Under Cover
Cowl Side TrimFront Door Inside Scuff Plate
± SFI (1MZ±FE)ENGINE CONTROL MODULE (ECM)
SF±73
1572 Author: Date:
ENGINE CONTROL MODULE (ECM)
COMPONENTS

SF08S±01
SF±74
± SFI (1MZ±FE)ENGINE CONTROL MODULE (ECM)
1573 Author: Date:
INSPECTION
1. REMOVE ECM
2. INSPECT ECM (See page DI±218)
3. REINSTALL ECM

S04528
5 mm
Hexagon
Wrench
Clip
SF08T±03
S05358
TOYOTA
Hand±Held Tester
B00623
Sound Scope
Sound Scope California A/T
Except California A/T
± SFI (1MZ±FE)FUEL CUT RPM
SF±75
1574 Author: Date:
FUEL CUT RPM
INSPECTION
1. REMOVE V±BANK COVER
(a) Using a 5 mm hexagon wrench, remove the 2 cap nuts.
(b) Disconnect the 2 clips, and remove the V±bank cover.
2. WARM UP ENGINE
Allow the engine to warm up to normal operating temperature.
3. CONNECT TOYOTA HAND±HELD TESTER OR OBDII
SCAN TOOL
(a) Connect the TOYOTA hand±held tester or OBDII scan
tool to the DLC3.
(b) Please refer to the TOYOTA hand±held tester or OBDII
scan tool operator's manual for further details.
4. INSPECT FUEL CUT OFF PRM
(a) Increase the engine speed to at least 3,500 rpm.
(b) Use a sound scope to check for injector operating noise.
(c) Check that when the throttle lever is released, injector op-
eration noise stops momentarily and then resumes.
HINT:
Measure with the A/C OFF.
Fuel return rpm: 1,200 rpm
5. DISCONNECT TOYOTA HAND±HELD TESTER OR
OBDII SCAN TOOL
6. REINSTALL V±BANK COVER
HINT:
For fixing the V±bank cover, push on the cover until a ºclickº is
felt.

ST03H±01
± STARTING (5S±FE)STARTING SYSTEM
ST±1
1708 Author: Date:
STARTING SYSTEM
ON±VEHICLE INSPECTION
NOTICE:
Before changing the starter, check the following items again:

Connector connection

Accessory installation, e.g.: theft deterrent system

ST03I±04
B01153
Throttle Cable
Clamp (A/T)Battery Tray
Cruise
Control
Actuator
Connector
Cruise Control Actuator Cruise Control
Cover
Clamp Hold Down Clamp
Starter Cable
Starter Connector
Starter
Battery
ST±2
± STARTING (5S±FE)STARTER
1709 Author: Date:
STARTER
COMPONENTS

B01154

Snap Ring
Starter Housing
Starter Clutch
Compression Spring
Clutch Shaft
Starter Housing and
Clutch Assembly
Idler Gear
Bearing Stop Collar
Pinion Gear
Compression Spring
Spring Retainer
Steel Ball
Return
Spring

Front Bearing
Armature

O±Ring
Field Frame
(Field Coil)
End Cover Brush Holder
Rear Bearing

Dust Protector

Non±reusable part
Magnetic Switch
Assembly

O±Ring
± STARTING (5S±FE)STARTER
ST±3
1710 Author: Date:

B06418
Magnetic Switch Assembly
Terminal Nut
Wave Washer
Terminal Insulator
O±RingContact Plate
Terminal
Bolt
Terminal Insulator
Terminal C Kit part
Plunger

Gasket
End Cover
O±Ring
Packing
Terminal Insulator
Wave Washer
Terminal Nut Terminal Bolt

Terminal 30 Kit PartContact PlateTerminal Insulator
N´m (kgf´cm, ft´lbf)

Non±reusable part: Specified torque
17 (173, 13)
17 (173, 13)
Lead Terminal
ST±4
± STARTING (5S±FE)STARTER
1711 Author: Date: