torque specifications TOYOTA CAMRY 1999 Service Workshop Manual

SS09Y±03
± SERVICE SPECIFICATIONSBRAKE
SS±63
226 Author: Date:
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
Master cylinder x Piston stopper bolt101007
Master cylinder x Reservoir1.71816 in.´lbf
Master cylinder x Brake booster131309
Brake line union nut 10 mm nut1515511
12 mm nut2020014
Brake booster clevis lock nut2526019
Brake booster x Pedal bracket131309
Brake pedal x Pedal bracket3940029
Pedal bracket x Instrument panel reinforcement131309
Front brake caliper installation bolt3435025
Bleeder plug8.38574 in.´lbf
Front brake torque plate x Steering knuckle1071,09079
Front brake caliper x Flexible hose2930021
Flexible hose x Shock absorber bracket2930021
Rear drum brake wheel cylinder x Backing plate101007
Parking brake cable bracket x Backing plate7.88069 in.´lbf
Rear brake caliper installation bolt2020014
Rear disc brake cariper main pin installation bolt2627020
Rear brake caliper x Flexible hose2930021
Rear brake torque plate x Rear axle carrier4747534
Proportioning valve installation bolt8.89078 in.´lbf
ABS actuator x Actuator bracket DENSO type5.45548 in.´lbf
ABS actuator x Actuator bracket BOSCH type9.09280 in.´lbf
ABS actuator x ECU BOSCH type2.62723 in.´lbf
ABS & TRAC actuator x Actuator bracket5.45548 in.´lbf
ABS (& TRAC) actuator bracket x Body1919514
Front speed sensor installation bolt7.88069 in.´lbf
Front speed sensor harness clamp bolt5.45548 in.´lbf
Rear speed sensor installation bolt7.88069 in.´lbf
Rear speed sensor harness clamp bolt5.45548 in.´lbf

SS06L±03
SS±64
± SERVICE SPECIFICATIONSSTEERING
227 Author: Date:
STEERING
SERVICE DATA
ON±VEHICLE INSPECTION
Steering wheel freeplayMaximum30 mm (1.18 in.)
5S±FE Engine :
Drive belt tension New belt95 ± 145 lbf
Drive belt tension Used belt60 ± 100 lbf
1MZ±FE Engine :
Drive belt tension New belt150 ± 185 lbf
Drive belt tension Used belt95 ± 135 lbf
Fluid level rise Maximum5 mm (0.20 in.)
Fluid pressure at idle speed with valve closed Minimum7,845 kPa (80 kgf/cm2, 1,138 psi)
Steering effort at idle speedMaximum5.9 N´m (60 kgf´cm, 52 in.´lbf)
PS VANE PUMP
5S±FE and 1MZ±FE Engines:
Vane pump rotating torqueMaximum0.3 N´m (2.8 kgf´cm, 2.4 in.´lbf)
Oil clearance between pump shaft and bushing STD0.03 ± 0.05 mm (0.0012 ± 0.0020 in.)
Oil clearance between pump shaft and bushingMaximum0.07 mm (0.0028 in.)
Vane plate heightMinimum8.6 mm (0.339 in.)
Vane plate thickness Minimum1.397 mm (0.0550 in.)
Vane plate lengthMinimum14.991 mm (0.5902 in.)
Clearance between the rotor groove and plateMaximum0.035 mm (0.0014 in.)
Vane plate length Pump rotor and cam ring mark
NONE14.999 ± 15.001 mm (0.59051 ± 0.59059 in.)
114.997 ± 14.999 mm (0.59043 ± 0.59051 in.)
214.995 ± 14.997 mm (0.59035 ± 0.59043 in.)
314.993 ± 14.995 mm (0.59027 ± 0.59035 in.)
414.991 ± 14.993 mm (0.59020 ± 0.59027 in.)
Spring free lengthMinimum32.3 mm (1.272 in.)
PS GEAR
Steering rack runout Maximum0.30 mm (0.0118 in.)
Total preload (Control valve rotating torque)0.8 ± 1.4 N´m (8 ± 14 kgf´cm, 6.9 ± 12.2 in.´lbf)

SS06M±01
± SERVICE SPECIFICATIONSSTEERING
SS±65
228 Author: Date:
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
STEERING COLUMN
Steering wheel pad set screw (Torx screw)7.17263 in.´lbf
Steering wheel set nut3536026
Intermediate shaft assembly x Control valve shaft3536026
Steering column assembly x Intermediate shaft assembly3536026
Steering column assembly set nut2526019
Turn signal bracket x Column tube77061 in.´lbf
Lower column tube attachment x Column tube1919514
PS VANE PUMP
5S±FE and 1MZ±FE Engines:
Pressure feed tube x Control valve housing 5S±FE Engine32 (25)326 (250)24 (18)
Pressure feed tube x Pressure feed tube 1MZ±FE Engine20 (25)203 (250)15 (18)
Clamp plate set nut 5S±FE Engine101007
Clamp plate set nut 1MZ±FE Engine7.88069 in.´lbf
PS vane pump set bolt A bolt29 (43)293 (440)21 (32)
PS vane pump set bolt B bolt4344032
Oil pressure switch x Union bolt2121015
Union bolt x Pressure feed tube5252538
Vane pump pulley set nut4344032
Front bracket x Rear bracket4344032
Suction port union set bolt131309
Pressure port union8385062
Rear housing set bolt2424017
PS GEAR
Pressure feed tube clamp plate set nut101007
Pressure feed and return tubes x Control valve housing32 (25)326 (250)24 (18)
Stabilizer bar set bolt1919514
PS gear assembly set bolt and nut1811,850134
Turn pressure tube union nut10 (13)102 (130)7 (9)
Tie rod end lock nut7475054
Rack x Rack end60 (83)615 (850)45 (62)
Rack guide spring cap lock nut50 (69)513 (700)37 (51)
Rack housing cap5960043
Selt±locking nut2525018
Control valve housing set bolt1818513
( ): For use without SST

SS061±17
SS±66
± SERVICE SPECIFICATIONSSUPPLEMENTAL RESTRAINT SYSTEM
229 Author: Date:
SUPPLEMENTAL RESTRAINT SYSTEM
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
Steering wheel3536026
Steering wheel pad7.17263 in.´lbf
Front passenger airbag assembly x Instrument panel reinforcement2020515
Front seat installation bolt3737527
Seatback frame set bolt Bolt A
(See page RS±49) Bolt B18
15185
15013
11
Airbag sensor assembly2020515
Front airbag sensor2020515
Side airbag sensor assembly2020515
Front seat outer belt retractor Upper bolt
Lower bolt7.5
4276
43066 in.´lbf
31

SS0BY±01
± SERVICE SPECIFICATIONSBODY
SS±69
232 Author: Date:
BODY
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
FRONT BUMPER±±±
Front bumper cover x Body5.55549 in.´lbf
Front bumper reinforcement x Body3435025
REAR BUMPER±±±
Rear bumper cover x Body5.05043 in.´lbf
Rear bumper reinforcement x Body3435025
HOOD±±±
Hood hinge x Hood2626019
Hood lock x Body8.08071 in.´lbf
FRONT AND REAR DOOR±±±
Front door hinge x Body3131022
Rear door hinge x Body2626019
Door hinge x Door panel2626019
Door lock striker x Body2626019
Outside rear view mirror x Front door panel5.55549
Door inside handle x Door panel3.53531 in.´lbf
Door glass x Window regulator8.08071 in.´lbf
Window regulator x Door panel5.55549 in.´lbf
Door lock x Door panel5.05043 in.´lbf
Door outside handle x Door panel7.07061 in.´lbf
Door check x Body3030022
Door check x Door panel8.08071 in.´lbf
LUGGAGE COMPARTMENT DOOR AND HINGE±±±
Luggage door hinge x Luggage door8.08071 in.´lbf
Luggage door lock striker x Body5.55549 in.´lbf
Luggage door lock x Luggage door5.55549 in.´lbf
FRONT WIPER AND WASHER±±±
Wiper motor assembly x Body2424518
Wiper arm x Wiper pivot5.55549 in.´lbf
SLIDING ROOF±±±
Sliding roof assembly x Body5.55549 in.´lbf
INSTRUMENT PANEL±±±
Front passenger airbag assembly x Reinforcement2020014
Steering wheel lock nut3536026
SEAT±±±
Front Seat (Power Seat for TMC Made)±±±
Hinge cover x Seatback frame1818513
Seatback frame x Power seat adjuster1515011
Seatback frame x Side airbag assembly6.06153 in.´lbf
Front Seat (Manual Seat for TMC Made)±±±
Front seat adjuster x Body3737527

SS05W±06
SS±72
± SERVICE SPECIFICATIONSAIR CONDITIONING
235 Author: Date:
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
Compressor x Discharge hose101007
Compressor x Suction hose101007
Condenser x Disaharge hose101007
Condenser x Liquid tube1414010
Receiver x Liquid tube5.45548 in.´lbf
Expansion valve x Evaporator5.45548in.´lbf
Compressor x Engine2525018
Compressor x Compressor bracket (1MZ±FE Only)2525018
Drive belt adjusting bar bracket x Compressor2525018
Drive belt adjusting bar bracket x Adjusting bar1818513
Pivot bolt 5S±FE5252038Pivot bolt 5S FE
1MZ±FE5657041
Adjusting lock bolt1818513
Pressure switch x Liquied tube101007
Pressure plate x Compressor13.21359
Suction line (Piping joint)3233024
Suction line (Block joint)101007

SS0ZT±01
SS±2
± SERVICE SPECIFICATIONSSTANDARD BOLT
SPECIFIED TORQUE FOR STANDARD BOLTS
Specified torque
ClassDiameter
mm
Pitch
mmHexagon head boltHexagon flange boltClassmmmmN´mkgf´cmft´lbfN´mkgf´cmft´lbf
4T
6
8
10
12
14
161
1.25
1.25
1.25
1.5
1.55
12.5
26
47
74
11 555
130
260
480
760
1,15048 in.´lbf
9
19
35
55
836
14
29
53
84
±60
145
290
540
850
±52 in.´lbf
10
21
39
61
±
5T
6
8
10
12
14
161
1.25
1.25
1.25
1.5
1.56.5
15.5
32
59
91
14065
160
330
600
930
1,40056 in.´lbf
12
24
43
67
1017.5
17.5
36
65
100
±75
175
360
670
1,050
±65 in.´lbf
13
26
48
76
±
6T
6
8
10
12
14
161
1.25
1.25
1.25
1.5
1.58
19
39
71
11 0
17080
195
400
730
1,100
1,75069 in.´lbf
14
29
53
80
1279
21
44
80
125
±90
210
440
810
1,250
±78 in.´lbf
15
32
59
90
±
7T
6
8
10
12
14
161
1.25
1.25
1.25
1.5
1.510.5
25
52
95
145
23011 0
260
530
970
1,500
2,3008
19
38
70
108
16612
28
58
105
165
±120
290
590
1,050
1,700
±9
21
43
76
123
±
8T
8
10
121.25
1.25
1.2529
61
11 0300
620
1,10022
45
8033
68
120330
690
1,25024
50
90
9T
8
10
121.25
1.25
1.2534
70
125340
710
1,30025
51
9437
78
140380
790
1,45027
57
105
10T
8
10
121.25
1.25
1.2538
78
140390
800
1,45028
58
10542
88
155430
890
1,60031
64
11 6
11 T
8
10
121.25
1.25
1.2542
87
155430
890
1,60031
64
11 647
97
175480
990
1,80035
72
130

SS0AH±04
SS±6
± SERVICE SPECIFICATIONSSFI
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
Fuel line for union for fuel inlet coupler
for others42
28428
28631
21
Fuel filter x Drain plug10.811 08
Fuel filter x Fuel filter bracket21.521916
Fuel filter x Union3131623
Oil separator x Fuel pressure regulator24.525018
Fuel pressure regulator x Bracket2020015
Fuel pressure regulator bracket x Body for 10 mm head bolt
for 12 mm head bolt9.9
19.6100
20088 in.´lbf
14
Fuel relief pipe x Fuel pressure regulator4242831
Delivery pipe x cylinder head1313010
Fuel tank band x Fuel tank frame5253038
Rear side plate x Front side plate1001,02074
Union x Fuel shutoff valve for fuel pipe filter pipe
for others31
18316
18423
13
Fuel tank bracket x Fuel tank valve case8.28473 in.´lbf
Fuel tank valve cover x Fuel tank valve case8.28473 in.´lbf
Fuel tank frame x Body60.261444
Performance rod x Body39.240029
Performance rod x Fuel tank band18.118513
Fuel shutoff valve core x Delivery pipe3535726
Fuel shutoff valve coil x Core1515311
Fuel temperature sensor x Delivery pipe20.420815
Fuel pressure sensor x Delivery pipe24.625118
Fuel pressure sensor x Fuel main pipe68.670051
Fuel inlet hose x Fuel pressure regulator9.910088 in.´lbf

SS0AN±04
SS±8
± SERVICE SPECIFICATIONSIGNITION
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
Spark plug x Cylinder head1818013

SS04W±03
± SERVICE SPECIFICATIONSSUSPENSION AND AXLE
SS±9
67 Author: Date:
SUSPENSION AND AXLE
SERVICE DATA
Vehicle heightFront*5218 mm (8.58 in.)Vehicle height
Tire size: 205/65R15Rear*6270 mm (10.63 in.)
Camber0°36'±45'(0 6°±075°)Camber
Ri h l f
±0°36' ± 45' (0.6° ± 0.75°)
45' (0 75°) lRight±left error45' (0.75°) or less
Front wheel
Caster
Right±left error2°10' ± 45' (2.17° ± 0.75°)
45' (0.75°) or less
Front wheel
alignmentSteering axis inclination
Right±left error13°01' ± 45' (13.02° ± 0.75°)
45' (0.75°) or less
Toe±in (Total)
Rack end length difference
0° ± 12' (0° ± 0.2° 0 ± 2 mm 0 ± 0.08 in.)
1.5 mm (0.059 in.) or less
Wheel angle Inside wheel35°50' ± 2° (35.84° ± 2°)Wheel angle Inside wheel
Outside wheel31°28' (31.47°)
Rear wheel
Camber
Right±left error±0°45' ± 45' (±0.75° ± 0.75°)
45' (0.75°) or less
Rear wheel
alignmentToe±in (total)
No. 2 lower suspension arm length difference0°24' ± 12' (0.4° ± 0.2°)
4 ± 2 mm (0.16 ± 0.08 in.)
1 mm (0.04 in.) or less
*1: Front measuring point
Measure the distance from the ground to the center of the front side lower suspension arm mounting bolt.
*
2: Rear measuring point
Measure the distance from the ground to the center of the front side strut rod mounting bolt.
FtlAxle bearing backlash Maximum0.05 mm (0.0020 in.)Front axleAxle hub deviationMaximum0.05 mm (0.0020 in.)
Front drive shaft
Drive shaft standard length
LH
RH
609.2 ± 2.0 mm (23.984 ± 0.079 in.)
842.9 ± 2.0 mm (33.185 ± 0.079 in.)
Ft iLower ball joint turning torque1.0 ± 3.4 N´m (10 ± 35 kgf´cm, 8.7 ± 30 in.´lbf)Front suspensionStabilizer bar link turning torque0.05 ± 1.0 N´m (0.5 ± 10 kgf´cm, 0.4 ± 8.7 in.´lbf)
RlAxle bearing backlash0.05 mm (0.0020 in.)Rear axleAxle hub deviation0.07 mm (0.0028 in.)
RiNo. 2 lower suspension arm length512.3 mm (20.169 in.)Rear suspensionStabilizer bar link turning torque0.05 ± 1.0 N´m (0.5 ± 10 kgf´cm, 0.4 ± 8.7 in.´lbf)