O2 sensor TOYOTA CAMRY 2000 Service Repair Manual

O2S TEST RESULTS (MODE 05) ± SS002-03December 17, 2003
Page 3 of 43
1. On the Diagnostic Tester* screen,
select the following menus:
DIAGNOSTICS
CARB OBD II
O2S TEST RESULTS
A list of the available oxygen sensors
will be displayed.
2. Select the desired oxygen sensor and
press Enter.
NOTE:
The monitor result of the A/F sensor will
not be displayed. If you select
ªBank 1±Sensor 1º or Bank 2±Sensor 1º
for a vehicle equipped with an A/F
sensor, the Diagnostic Tester will
display ªNo parameter to display.º
3. Compare the test results with the
values listed in the Failure
Threshold Chart.
* Although this procedure references the Toyota
Diagnostic Tester, the O2S test results can be
checked using a generic OBDII scantool.
Refer to your OBDII scantool operator's manual
for specific procedures.
Accessing
O2S Test
ResultsO2S TEST RESULT Screen
01 BANK 1 ± SENSOR 1
01 BANK 1 ± SENSOR 2
01 BANK 2 ± SENSOR 1
01 BANK 2 ± SENSOR 2
TEST DATA Screen
LOW SW V 0.400 V
HIGH SW V 0.550 V
MIN O2S V 0.100 V
MAX O2S V 0.900 V
TIME $81 17

NOTE:
Before the O2S Monitor completes or after the ignition switch is turned OFF, the
Diagnostic Tester displays the viewable upper limit or a lower limit of the test value
(example: 0 V, 1.275 V, 0 s [seconds], 10.2 s, 0 and 255).
O2S TEST RESULTS (MODE 05) ± SS002-03December 17, 2003
Page 4 of 43
1. Determine the correct O2S Failure Threshold Chart for your vehicle by looking in the
ªO2S Application Table,º pages 5 ± 9 in this bulletin.
2. Select appropriate year, model, and engine for specified O2S Failure
Threshold Chart.
3. Compare O2S test results with the specified O2S Failure Threshold Chart. It may be
necessary to convert O2S test results to a specific measurement unit using the
conversion factor that is supplied in the specified table. See example below:
Example:
A. The Diagnostic Tester displays
ª17º as a value of the ªTime $81º
(see illustration).
B. Find the Conversion Factor value
of ªTime $81º in the O2S Failure
Threshold chart below.
0.3906 is specified for Time $81
in this chart.
C. Multiply ª17º in step ªAº by 0.3906
(Conversion Factor) in step ªB.º
17 x 0.3906 = 6.6 %
D. If the answer is within the
Standard Value of TEST LIMIT,
the ªTime $81º can be confirmed
to be normal.
Example of O2S Failure Threshold Chart:
TEST ID
DESCRIPTION OF TEST DATACONVERSION
FACTORUNITSTANDARD VALUE
OF TEST LIMIT
Time
$81Percentage of monitoring time
where Oxygen Sensor voltage is
less than 0.05V
Multiply 0.3906%Within 60%
Comparing
O2S Test
Results to
Failure
Thresholds
Example
LOW SW V 0.400 V
HIGH SW V 0.550 V
MIN O2S V 0.035 V
MAX O2S V 0.835 V
Time $81 17
Time $84 84
Time $85 79
NOTE:
ªLOW SW Vº indicates the O2S
voltage when the O2S status changes
from rich to lean.
ªHIGH SW Vº indicates the O2S
voltage when the O2S status changes
from lean to rich.
If the O2S voltage is lower than
ªLOW SW V,º the O2S status is lean.
If the O2S voltage is higher than
ªHIGH SW V,º the O2S status is rich.

O2S TEST RESULTS (MODE 05) ± SS002-03December 17, 2003
Page 10 of 43
CHART 1:
Front O2S (Bank 1 Sensor 1 and Bank 2 Sensor 1) Voltage Monitor
Related DTCs: P0130, P0150, P2195, P2196, P2197 and P2198
TEST IDDESCRIPTION OF TEST DATACONVERSION
FACTORUNITSTANDARD VALUE
OF TEST LIMIT
Time
$07The minimum voltage during O2S
monitoringN/AVBetween 0 and 0.4 V
Time
$08The maximum voltage during
O2S monitoringN/AVBetween 0.55 and
1.275 V
If the sensor voltage is out of the standard value, the ECM interprets this as a malfunction.
Front O2S (Bank 1 Sensor 1 and Bank 2 Sensor 1) Response Monitor
Related DTCs: P0133 and P0153
TEST IDDESCRIPTION OF TEST DATACONVERSION
FACTORUNITSTANDARD VALUE
OF TEST LIMIT
Time
$31Time to change from Lean
(30.4 V) to Rich (.0.55 V)N/ASecondBetween 0 and
1 second
Time
$32Time to change from Rich
(.0.55 V) to Lean (.0.4 V)N/ASecondBetween 0 and
1 second
If the time required to change is out of the standard value, the ECM interprets this as a malfunction.
Rear O2S (Bank 1 Sensor 2 and Bank 2 Sensor 2) Voltage Monitor
Related DTCs: P0136 and P0156
TEST IDDESCRIPTION OF TEST DATACONVERSION
FACTORUNITSTANDARD VALUE
OF TEST LIMIT
Time
$07The minimum voltage during O2S
monitoringN/AVBetween 0 and 0.4 V
Time
$08The maximum voltage during
O2S monitoringN/AVBetween 0.5 and
1.275 V
If the sensor voltage is out of the standard value, the ECM interprets this as a malfunction. O2S
Failure
Threshold
Charts

O2S TEST RESULTS (MODE 05) ± SS002-03December 17, 2003
Page 11 of 43
CHART 2:
Front O2S (Bank 1 Sensor 1 and Bank 2 Sensor 1) Voltage Monitor
Related DTCs: P0130, P0150, P2195, P2196, P2197 and P2198
TEST IDDESCRIPTION OF TEST DATACONVERSION
FACTORUNITSTANDARD VALUE
OF TEST LIMIT
$07The minimum voltage during
O2S monitoringN/AVBetween 0 and
0.35 V
Time
$08The maximum voltage during
O2S monitoringN/AVBetween 0.55 and
1.275 V
If the sensor voltage is out of the standard value, the ECM interprets this as a malfunction.
Front O2S (Bank 1 Sensor 1 and Bank 2 Sensor 1) Response Monitor
Related DTCs: P0133 and P0153
TEST IDDESCRIPTION OF TEST DATACONVERSION
FACTORUNITSTANDARD VALUE
OF TEST LIMIT
Time
$31Time to change from Lean
(30.35 V) to Rich (.0.55 V)N/ASecondBetween 0 and
1.1 seconds
Time
$32Time to change from Rich
(.0.55 V) to Lean (.0.35 V)N/ASecondBetween 0 and
1.1 seconds
If the time required to change is out of the standard value, the ECM interprets this as a malfunction.
Rear O2S (Bank 1 Sensor 2 and Bank 2 Sensor 2) Voltage Monitor
Related DTCs: P0136 and P0156
TEST IDDESCRIPTION OF TEST DATACONVERSION
FACTORUNITSTANDARD VALUE
OF TEST LIMIT
Time
$07The minimum voltage during
O2S monitoringN/AVBetween 0 and 0.4 V
Time
$08The maximum voltage during
O2S monitoringN/AVBetween 0.5 and
1.275 V
If the sensor voltage is out of the standard value, the ECM interprets this as a malfunction. O2S
Failure
Threshold
Charts
(Continued)

O2S TEST RESULTS (MODE 05) ± SS002-03December 17, 2003
Page 12 of 43
CHART 3:
Rear O2S (Bank 1 Sensor 2 and Bank 2 Sensor 2) Voltage Monitor
Related DTCs: P0136 and P0156
TEST IDDESCRIPTION OF TEST DATACONVERSION
FACTORUNITSTANDARD VALUE
OF TEST LIMIT
Time
$07The minimum voltage during
O2S monitoringN/AVBetween 0 and
0.45 V
Time
$08The maximum voltage during
O2S monitoringN/AVBetween 0.6 and
1.275 V
If the sensor voltage is out of the standard value, the ECM interprets this as a malfunction.
CHART 4:
Rear O2S (Bank 1 Sensor 2 and Bank 2 Sensor 2) Voltage Monitor
Related DTCs: P0136 and P0156
TEST IDDESCRIPTION OF TEST DATACONVERSION
FACTORUNITSTANDARD VALUE
OF TEST LIMIT
Time
$07The minimum voltage during
O2S monitoringN/AVBetween 0 and 0.4 V
Time
$08The maximum voltage during
O2S monitoringN/AVBetween 0.6 and
1.275 V
If the sensor voltage is out of the standard value, the ECM interprets this as a malfunction. O2S
Failure
Threshold
Charts
(Continued)

O2S TEST RESULTS (MODE 05) ± SS002-03December 17, 2003
Page 13 of 43
CHART 5:
Front O2S (Bank 1 Sensor 1 and Bank 2 Sensor 1) Voltage Monitor
Related DTCs: P0130, P0150, P2195, P2196, P2197 and P2198
TEST IDDESCRIPTION OF TEST DATACONVERSION
FACTORUNITSTANDARD VALUE
OF TEST LIMIT
Time
$07The minimum voltage during
O2S monitoringN/AVBetween 0 and 0.4 V
Time
$08The maximum voltage during
O2S monitoringN/AVBetween 0.55 and
1.275 V
If the sensor voltage is out of the standard value, the ECM interprets this as a malfunction.
Front O2S (Bank 1 Sensor 1 and Bank 2 Sensor 1) Response Monitor
Related DTCs: P0133 and P0153
TEST IDDESCRIPTION OF TEST DATACONVERSION
FACTORUNITSTANDARD VALUE
OF TEST LIMIT
Time
$31Time to change from Lean
(30.4 V) to Rich (.0.55 V)N/ASecondBetween 0 and
1.1 seconds
Time
$32Time to change from Rich
(.0.55 V) to Lean (30.4 V)N/ASecondBetween 0 and
1.1 seconds
If the time required to change is out of the standard value, the ECM interprets this as a malfunction.
Rear O2S (Bank 1 Sensor 2 and Bank 2 Sensor 2) Voltage Monitor
Related DTCs: P0136 and P0156
TEST IDDESCRIPTION OF TEST DATACONVERSION
FACTORUNITSTANDARD VALUE
OF TEST LIMIT
Time
$07The minimum voltage during
O2S monitoringN/AVBetween 0 and 0.4 V
Time
$08The maximum voltage during
O2S monitoringN/AVBetween 0.5 and
1.275 V
If the sensor voltage is out of the standard value, the ECM interprets this as a malfunction.
CHART 6:
Rear O2S (Bank 1 Sensor 2 and Bank 2 Sensor 2) Voltage Monitor
Related DTCs: P0136 and P0156
TEST IDDESCRIPTION OF TEST DATACONVERSION
FACTORUNITSTANDARD VALUE
OF TEST LIMIT
Time
$07The minimum voltage during
O2S monitoringN/AVBetween 0 and
0.55 V
Time
$08The maximum voltage during
O2S monitoringN/AVBetween 1 and
1.275 V
If the sensor voltage is out of the standard value, the ECM interprets this as a malfunction. O2S
Failure
Threshold
Charts
(Continued)

O2S TEST RESULTS (MODE 05) ± SS002-03December 17, 2003
Page 14 of 43
CHART 7:
Front O2S (Bank 1 Sensor 1 and Bank 2 Sensor 1) Voltage Monitor
Related DTCs: P0130, P0150, P2195, P2196, P2197 and P2198
TEST IDDESCRIPTION OF TEST DATACONVERSION
FACTORUNITSTANDARD VALUE
OF TEST LIMIT
Time
$07The minimum voltage during
O2S monitoringN/AVBetween 0 and 0.4 V
Time
$08The maximum voltage during
O2S monitoringN/AVBetween 0.55 and
1.275 V
If the sensor voltage is out of the standard value, the ECM interprets this as a malfunction.
Front O2S (Bank 1 Sensor 1 and Bank 2 Sensor 1) Response Monitor
Related DTCs: P0133 and P0153
TEST IDDESCRIPTION OF TEST DATACONVERSION
FACTORUNITSTANDARD VALUE
OF TEST LIMIT
Time
$31Time to change from Lean
(30.4 V) to Rich (.0.55 V)N/ASecondBetween 0 and
0.9 seconds
Time
$32Time to change from Rich
(.0.55 V) to Lean (30.4 V)N/ASecondBetween 0 and
0.9 seconds
If the time required to change is out of the standard value, the ECM interprets this as a malfunction.
Rear O2S (Bank 1 Sensor 2 and Bank 2 Sensor 2) Voltage Monitor
Related DTCs: P0136 and P0156
TEST IDDESCRIPTION OF TEST DATACONVERSION
FACTORUNITSTANDARD VALUE
OF TEST LIMIT
Time
$07The minimum voltage during
O2S monitoringN/AVBetween 0 and 0.4 V
Time
$08The maximum voltage during
O2S monitoringN/AVBetween 0.5 and
1.275 V
If the sensor voltage is out of the standard value, the ECM interprets this as a malfunction. O2S
Failure
Threshold
Charts
(Continued)

O2S TEST RESULTS (MODE 05) ± SS002-03December 17, 2003
Page 15 of 43
CHART 8:
Front O2S (Bank 1 Sensor 1 and Bank 2 Sensor 1) Voltage Monitor
Related DTCs: P0130, P0150, P2195, P2196, P2197 and P2198
TEST IDDESCRIPTION OF TEST DATACONVERSION
FACTORUNITSTANDARD VALUE
OF TEST LIMIT
Time
$07The minimum voltage during
O2S monitoringN/AVBetween 0 and
0.35 V
Time
$08The maximum voltage during
O2S monitoringN/AVBetween 0.55 and
1.275 V
If the sensor voltage is out of the standard value, the ECM interprets this as a malfunction.
Front O2S (Bank 1 Sensor 1 and Bank 2 Sensor 1) Response Monitor
Related DTCs: P0133 and P0153
TEST IDDESCRIPTION OF TEST DATACONVERSION
FACTORUNITSTANDARD VALUE
OF TEST LIMIT
Time
$31Time to change from Lean
(30.35 V) to Rich (.0.55 V)N/ASecondBetween 0 and
1 second
Time
$32Time to change from Rich
(.0.55 V) to Lean (30.35 V)N/ASecondBetween 0 and
1 second
If the time required to change is out of the standard value, the ECM interprets this as a malfunction.
Rear O2S (Bank 1 Sensor 2 and Bank 2 Sensor 2) Voltage Monitor
Related DTCs: P0136 and P0156
TEST IDDESCRIPTION OF TEST DATACONVERSION
FACTORUNITSTANDARD VALUE
OF TEST LIMIT
Time
$07The minimum voltage during
O2S monitoringN/AVBetween 0 and 0.4 V
Time
$08The maximum voltage during
O2S monitoringN/AVBetween 0.6 and
1.275 V
If the sensor voltage is out of the standard value, the ECM interprets this as a malfunction.
CHART 9:
Rear O2S (Bank 1 Sensor 2 and Bank 2 Sensor 2) Voltage Monitor
Related DTCs: P0136 and P0156
TEST IDDESCRIPTION OF TEST DATACONVERSION
FACTORUNITSTANDARD VALUE
OF TEST LIMIT
Time
$07The minimum voltage during
O2S monitoringN/AVBetween 0 and 0.5 V
Time
$08The maximum voltage during
O2S monitoringN/AVBetween 0.6 and
1.275 V
If the sensor voltage is out of the standard value, the ECM interprets this as a malfunction. O2S
Failure
Threshold
Charts
(Continued)

O2S TEST RESULTS (MODE 05) ± SS002-03December 17, 2003
Page 16 of 43
CHART 10:
Front O2S (Bank 1 Sensor 1 and Bank 2 Sensor 1) Voltage Monitor
Related DTCs: P0130, P0150, P2195, P2196, P2197 and P2198
TEST IDDESCRIPTION OF TEST DATACONVERSION
FACTORUNITSTANDARD VALUE
OF TEST LIMIT
Time
$07The minimum voltage during
O2S monitoringN/AVBetween 0 and 0.4 V
Time
$08The maximum voltage during
O2S monitoringN/AVBetween 0.55 and
1.275 V
If the sensor voltage is out of the standard value, the ECM interprets this as a malfunction.
Front O2S (Bank 1 Sensor 1 and Bank 2 Sensor 1) Response Monitor
Related DTCs: P0133 and P0153
TEST IDDESCRIPTION OF TEST DATACONVERSION
FACTORUNITSTANDARD VALUE
OF TEST LIMIT
Time
$31Time to change from Lean
(30.4 V) to Rich (.0.55 V)N/ASecondBetween 0 and
1.1 seconds
Time
$32Time to change from Rich
(.0.55 V) to Lean (30.4 V)N/ASecondBetween 0 and
1.1 seconds
If the time required to change is out of the standard value, the ECM interprets this as a malfunction.
Rear O2S (Bank 1 Sensor 2 and Bank 2 Sensor 2) Voltage Monitor
Related DTCs: P0136 and P0156
TEST IDDESCRIPTION OF TEST DATACONVERSION
FACTORUNITSTANDARD VALUE
OF TEST LIMIT
Time
$07The minimum voltage during
O2S monitoringN/AVBetween 0 and 0.5 V
Time
$08The maximum voltage during
O2S monitoringN/AVBetween 0.6 and
1.275 V
If the sensor voltage is out of the standard value, the ECM interprets this as a malfunction. O2S
Failure
Threshold
Charts
(Continued)

O2S TEST RESULTS (MODE 05) ± SS002-03December 17, 2003
Page 17 of 43
CHART 11:
Front O2S (Bank 1 Sensor 1 and Bank 2 Sensor 1) Voltage Monitor
Related DTCs: P0130, P0150, P2195, P2196, P2197 and P2198
TEST IDDESCRIPTION OF TEST DATACONVERSION
FACTORUNITSTANDARD VALUE
OF TEST LIMIT
Time
$07The minimum voltage during
O2S monitoringN/AVBetween 0 and
0.42 V
Time
$08The maximum voltage during
O2S monitoringN/AVBetween 0.48 and
1.275 V
If the sensor voltage is out of the standard value, the ECM interprets this as a malfunction.
Front O2S (Bank 1 Sensor 1 and Bank 2 Sensor 1) Response Monitor
Related DTCs: P0133 and P0153
TEST IDDESCRIPTION OF TEST DATACONVERSION
FACTORUNITSTANDARD VALUE
OF TEST LIMIT
Time
$31Time to change from Lean
(30.42 V) to Rich (.0.48 V)N/ASecondBetween 0 and
0.4 seconds
Time
$32Time to change from Rich
(.0.48 V) to Lean (30.42 V)N/ASecondBetween 0 and
0.4 seconds
If the time required to change is out of the standard value, the ECM interprets this as a malfunction.
Rear O2S (Bank 1 Sensor 2 and Bank 2 Sensor 2) Voltage Monitor
Related DTCs: P0136 and P0156
TEST IDDESCRIPTION OF TEST DATACONVERSION
FACTORUNITSTANDARD VALUE
OF TEST LIMIT
Time
$07The minimum voltage during
O2S monitoringN/AVBetween 0 and
0.45 V
Time
$08The maximum voltage during
O2S monitoringN/AVBetween 0.55 and
1.275 V
If the sensor voltage is out of the standard value, the ECM interprets this as a malfunction. O2S
Failure
Threshold
Charts
(Continued)