change wheel TOYOTA CAMRY 2000 Service Repair Manual

CAMRY
CAMRY ± OUTLINE OF NEW FEATURES 26
OUTLINE OF NEW FEATURES
The CAMRY is a high-quality family sedan with advanced technology and sporty performance. The following
changes are made for the 2000 model year.
1. Model Line-Up
The 5S-FNE CNG (Compressed Natural Gas) engine model has been added.
2. Exterior
Four new exterior colors have been added, for a total of 10 colors.
The design of the front and rear bumpers has been changed.
The bumper and the radiator grille have been made separate, and the radiator grille is chrome-plated.
The side protection molding has been increased in size. On the XLE grade model, chrome stripes have been
adopted for the side protection molding.
The 4-light multi-reflector type headlights are adopted with new styling.
The design and styling of the rear combination light has been changed.
The 16º aluminum alloy wheel and wheel cap has been added.
The styling of the 15º full wheel cover has been changed.
3. Interior
Wood-grain panels have been adopted in the interior of the XLE grade model.
CRS tether anchor brackets have been provided on the package tray trim. (except 5S-FNE engine Model)
A clock with an outside temperature gauge has been provided on the models with manual air conditioning.
4. 5S-FE Engine
The intake system from the inlet duct to the throttle body has been improved to increase torque and reduce
noise.
The direction of the rotation of the radiator cooling fan has been reversed.
A 2-way exhaust control system has been adopted on the TMMK made model.
Along with the discontinuance of the air assist system, the fuel injectors and the IAC valve have been
changed for the California specification model, in order to meet ULEV (Ultra-Low Emission Vehicle) re-
quirement.
The system for detecting evaporative emission leaks has been changed. For details, see the General 2000
Features section.
5. 5S-FNE Engine
Based on the 5S-FE gasoline engine, the 5S-FNE engine uses compressed natural gas. The fuel lines have
been designed exclusively for compressed natural gas application.
6. 1MZ-FE Engine
The system for detecting evaporative emission leaks has been changed. For details, see the General 2000
Features section.
A diagnostic trouble code (DTC) has been added for indicating a thermostat malfunction.
7. Automatic Transaxle
The overdrive switch has been changed to the momentary type. For details, see the General 2000 Features
section.
The differential gear ratio of the A140E automatic transaxle has been changed for the 5S-FNE engine mod-
el to accommodate the performance of the 5S-FNE engine.

3
CAMRY ± NEW FEATURES55
BRAKES
The specifications of the front and rear brakes have been changed.

Specifications 
'00 Model'00 Model'99 Model
Item5S-FE
5S-FNE1MZ-FE5S-FE1MZ-FE
TypeVentilated
Disc
Front
Caliper TypePE57*1,
PE60*
2AX60PE57AX60
Front
Disc
Brake
Wheel Cylinder Dia.
mm (in.)57.22 (2.25)*1
60.33 (2.38)*260.33 (2.38)57.22 (2.25)60.33 (2.38)
Brake
Rotor Size (D x T)*3
mm (in.)
255 x 28*1
(10.04 x 1.10)
275 x 28*
2
(10.83 x 1.10)
275 x 28
(10.83 x 1.10)255 x 28
(10.04 x 1.10)275 x 28
(10.83 x 1.10)
Rear
TypeLeading-
TrailingLeading-
Trailing
Rear
Drum
Brake
Wheel Cylinder Dia.
mm (in.)20.64 (0.81)20.64 (0.81)
BrakeDrum Inner Dia.
mm (in.)288.6 (9.00)288.6 (9.00)
TypeSolid DiscSolid Disc
Rear
DiscCaliper TypePD35R*4
AXS35R*5PD35R
Disc
BrakeWheel Cylinder Dia.
mm (in.)34.93 (1.38)34.93 (1.38)
Rotor Size (D x T)*3
mm (in.)
269 x 10
(10.59 x 0.39)269 x 10
(10.59 x 0.39)
*1: Models with 14º Tire
*
2: Models with 15º Tire
*
3: D: Outer Diameter, T: Thickness
*
4: TMC Made
*
5: TMMK Made

CAMRY - OUTLINE OF NEW FEATURES
CAMRY
172CM01
2
OUTLINE OF NEW FEATURES
The Camry is a high-quality family sedan with advanced technology and sporty performance. The following
changes are made for the 2001 model year.
1. 5S-FE Engine
The 5S-FE engine that are equipped on the '00 California specification models, which comply with the U-
LEV (Ultra-Low Emission Vehicle) requirements, have now been provided on the all models.
2. 1MZ-FE Engine
The 1MZ-FE engine that are equipped on the '00 California specification models, which comply with the
LEV (Low Emission Vehicle) requirements, have now been provided on the all models with the automatic
transaxle.
3. Brake
The size of front brake disc on 5S-FE engine model of CE grade has been changed from usual 255 mm (10.0
in.) for the 14-inch wheel to 275 mm (10.8 in.) for the 15-inch wheel.
4. Seat
A seat heater is established as an option to the driver seat and front passenger seat of the vehicle with leather
seats for Canada, thus improved the heating performance in the cold districts.
5. Internal Trunk Release Handle
An internal trunk release handle is included inside the trunk in case a person inadvertently locks oneself with-
in the trunk and needs to free oneself.
The handle is made of phosphorecent so that it is visible in the trunk for a while even after the trunk has been
closed.

22
INTERIOR

Layout of Audio System
 TILT STEERING
The tilt steering is standard on all models.
The steering wheel position can be changed to any of 6 positions..
 POWER WINDOW SYSTEM
A power window system is standard on the LE and XLE grade models and optional on the CE grade model. The power
window system includes one±touch auto down and key±off operation functions. The one±touch auto down function
automatically opens the driver's side window fully. The key±off operation function makes it possible to operate the
power windows for approximately 45 seconds after the ignition key is turned to the ACC or LOCK position, if the
front doors are not opened.
 DOOR LOCK CONTROL SYSTEM
The door lock control system with 2±step unlock function is standard on the LE and XLE grade model and optional
as a set with the power window system on the CE grade model. With the 2±step function, turning the key once in
the driver's door unlocks the driver's door only. Turning it twice unlocks all the doors.
A key confinement prevention function is provided. When the door is opened and the door lock button is locked
with the key still inserted in the ignition key cylinder, the key confinement prevention mechanism immediately
turns the door lock button to unlock. This prevents the key from being inadvertently locked inside the vehicle.

62CHASSISÐBRAKES
 MASTER CYLINDER
As in the previous model, the lockheed and
lockheed type master cylinder is used on the models
without ABS, and the portless and lockheed type
master cylinder is used on the models with ABS.
The portless and portless type master cylinder is
used on the models with ABS & TRAC system.
 ABS
1. General
As in the previous model, the braking of each wheel is controlled by the following 3 modes: pressure reduction,
pressure holding, and pressure holding mode.
During ABS activation, the ECU controls the fluid pressure of each front left and right wheels independently while
the fluid pressure of rear left and right wheels is controlled simultaneously.
However, the ABS actuator has been changed as shown in the table below. In addition, the diagnostic codes have
alsom been changed.
For diagnostic code check method, diagnostic code and diagnostic code clearance, see the 1997 Camry Repair
Manual (Pub. No. RM503U).
The operation of the ABS is the same as that of the '96 Corolla.

Type of ABS Actuator
Model
NewPreviousTypeNewPrevious
NIPPONDENSO ABS
(TMC Produced Model) 2±Position Solenoid Valve Type
Actuator
The ECU and realy are separate.3±Position Solenoid Valve Type
Actuato
The ECU and relay are separate.
BOSCH ABS
(TMM Produced Model)2±Position Solenoid Valve Type
Actuator with ECU and Relay3±Position Solenoid Valve and
Mechanical Valve Type Actuator
with ECU and Relay

73 CHASSISÐBRAKES
6. Construction and Operation of Components
TRAC OFF Switch and Indicator Light
1) TRAC OFF Switch
When pressing, this switch turns the TRAC system to be inoperative. Pressing it again changes it to be operative.
When turning the ignition switch from ªOFFº to ªONº, TRAC system always becomes operative.
2) TRAC OFF Indicator Light
This light comes on when the TRAC system is set inoperative by the TRAC OFF switch, and informs the driver
accordingly. And blinks to alert the driver when a malfunction has occurred in the engine and TRAC system.
3) Slip Indicator Light
When the TRAC system is operative, the light blinks and informs the driver accordingly.
ABS & TRAC Actuator
1) Construction
The ABS & TRAC actuator consists of 12 two±position solenoid valves, 1 motor, 2 pumps 2 reservoirs and 2 pressure
regulator valves.
The 12 two±position solenoid valves consists of 2 master cut solenoid valves, 2 reservoirs cut solenoid valves, 4
pressure holding valves, and 4pressure reduction valves.
Pressure regulator valve is assembled into the master cut solenoid valve.
The basic construction and operation of the pump, reservoir, pressure holding valve, and pressure reduction valve
are shared with ABS.
a. Master Cut Solenoid Valve
When the TRAC system is active, a signal from the ABS & TRAC ECU causes the master cut solenoid valve to turn
ON in order to shut off the circuit between the master cylinder and the front brake wheel cylinder.

111 BODY ELECTRICALÐACCESSORIES
 SRS AIRBAG
1. General
The SRS (Supplemental Restraint System) airbag is designed to help lessening the shock to the driver and front
passenger as a supplement to the seat belt. In a collision, the aribag sensor detects the shock and if the front±to±rear
shock is greater than a specified value, the airbags stored in the steering wheel pad for the driver and above the glove
box for the front passenger inflate instantly to help reducing the likelihood of the driver's or front passenger's head
and chest directly hitting the steering wheel or instrument panel.
As in the '96 Avalon, a 1±sensor type airbag system is used, in chich the detection of deceleration during a collision
is accomplished by the airbag sensor enclosed in the airbag snesor assembly.
The airbag system is controlled by the airbag sensor assembly. It has a self±diagnosis function. When it detects a
system malfunction, it lights up the SRS warning light on the combination meter to alert the driver.
The basic construction and operation are the same as in teh '96 Avalon. However, 2 types of the inflator for front
passenger have been adopted in the new Camry: TRW made and Morton made. Also, the construction of airbag sensor
assembly has been changed.

System Diagram
The activation processes of the SRS airbag is as illustrated below.

'99camry U
28
CAUTION
The SRS side airbags are installed in
the driver and front passenger seats.
Observe the following precautions.

Do not lean against the front door
when the vehicle is in use. The side
airbag inflates with considerable
speed and force; you may be killed
or seriously injured.

Do not modify or replace the seats
or surface of the front seats with
the side airbags. Such changes may
disable the system or cause the
side airbags to inflate, resulting in
death or serious injury. Consult
your Toyota dealer.

Do not use accessories for the
seats which cover the parts where
the side airbags should inflate.
Such accessories may prevent the
side airbags from activating correct-
ly, causing death or serious injury.
Adjust the driver's seat so that the foot
pedals, steering wheel and instrument
panel controls are within easy reach of
the driver.
CAUTION

Adjustments should not be made
while the vehicle is moving, as the
seat may unexpectedly move and
cause the driver to lose control of
the vehicle.

When adjusting the seat, be careful
not to hit the seat against a pas-
senger or luggage.

After adjusting the seat position,
try sliding it forward and backward
to make sure it is locked in posi-
tion.

After adjusting the seatback, exert
body pressure to make sure it is
locked in position.

Do not put objects under the seats.
The objects may interfere with the
seat±lock mechanism or unexpect-
edly push up the seat position ad-
justing lever; the seat may suddenly
move, causing the driver to lose
control of the vehicle.

While adjusting the seat, do not put
your hands under the seat or near
the moving parts. You may catch
and injure your hands or fingers.
Front seatsÐ
ÐFront seat precautions
(with SRS side airbags)ÐSeat adjustment
precautions

'99camry U
46

Do not modify or remove any wir-
ing. Do not modify, remove, strike
or open any components such as
the steering wheel column cover,
front passenger airbag cover, front
passenger airbag, airbag sensor as-
sembly. Doing any of these may
cause sudden SRS airbag inflation
or disable the system, which could
result in death or serious injury.
Failure to follow these instructions
can result in death or serious inju-
ries.NOTICE
Do not perform any of the following
changes without consulting your
Toyota dealer. Such changes can
interfere with proper operation of the
SRS airbag system in some cases.
Installation of electronic items such
as a mobile two±way radio, cassette
tape player or compact disc player
Modification of the suspension sys-
tem
Modification of the front end struc-
ture
Attachment of a grille guard (bull
bar, kangaroo bar, etc.), snowplow,
winches or any other equipment to
the front end
Repairs made on or near the front
fenders, front end structure, con-
sole, steering column, steering
wheel or dashboard near the front
passenger airbag
This SRS airbag system has a service
reminder indicator to inform the driver of
operating problems. If either of the
following conditions occurs, this indicates
a malfunction of the airbags. Contact your
Toyota dealer as soon as possible to
service the vehicle.

The light does not come on when the
ignition key is turned to the ºACCº or
ºONº position, or remains on.

The light comes on while driving.

'99camry U
73
Outside anchorsÐ
a. Should you select to use the outer
anchor positions, please contact your
Toyota dealer for proper modifications to
the filler panel.
b. After modifications have been made to
the filler panel, insert a 15 mm (0.6 in.)
spacer and tighten down the anchor brack-
et for your child restraint system with a
bolt. Torque the bolt to 16.5Ð24.7 NVm
(1.68Ð2.52 kgfVm, 12.2Ð18.2 ftVlbf).
c. Securely latch the hook of the top strap
onto the anchor bracket and make sure
the hook does not make contact with the
filler panel.To comply with Canadian Motor Vehicle
Safety Standards, this model sold in Can-
ada is provided with a bracket set in the
glovebox, designed for use with any of the
3 anchor locations shown in the illustra-
tion.
If your child restraint system does not
provide any of the necessary parts, ask
your Toyota dealer. (See ºÐChild restraint
systemº.)
Tilt steering wheel
To change the steering wheel angle,
hold the steering wheel, pull up the
lock release lever, tilt the steering
wheel to the desired angle and release
the lever.
When the steering wheel is in a low posi-
tion, it will spring up as you release the
lock release lever.