oil filter TOYOTA DYNA 100/150 2014 Owners Manual (in English)

8OVERVIEW OF INSTRUMENTS AND CONTROLS
Brake system warning light

Charging system warning light

Low engine oil pressure warning light

Low engine oil level warning light

Malfunction indicator lamp

Low fuel level warning light

Anti−lock brake system warning light

SRS warning light

DPF (Diesel Particulate Filter) system indicator
light

Timing belt replacement warning light

Fuel filter warning light

Engine oil change reminder light

Headlight high beam indicator light
Dyna100/150_EE
Indicator symbols on the instrument panel

70GAUGES, METERS AND SERVICE REMINDER INDICATORS
This meter displays the odometer and
two trip meters.
1. Odometer—Shows the total distance
the vehicle has been driven.
2. Two trip meters—Show two different
distances independently driven since
the last time each trip meter was set
to zero.
You can use one trip meter to calculate
the fuel economy and the other to
measure the distance on each trip. All
trip meter data is cancelled if the elec-
trical power source is disconnected.
3. Trip meter reset knob—Resets the two
trip meters to zero, and also change
the meter display.
To change the meter display, quickly
push and release the knob. The meter
display changes in the order from the
odometer to trip meter A to trip meter
B, then back to the odometer each
time you push.
To reset the trip meter A to zero, dis-
play the meter A reading, then push
and hold the knob until the meter is
set to zero. The same process can be
applied for resetting the trip meter B.The oil maintenance management sys-
tem (OMMS) is designed to inform you,
by means of a light, of the time to
change the engine oil and oil filter.
ENGINE OIL AND OIL FILTER CHANGE
Change the engine oil and oil filter in
either of the following cases:
DWhen the engine oil change reminder
light is lit.
DWhen the system is repaired.
DWhen the engine oil change reminder
light does not come on even if two
years have passed since the engine
oil was changed.
DWhen the engine oil change reminder
light does not come on even if you
have driven over 30000 km (18000
miles) since the engine oil was
changed.
The lighting timing will change according
to the driving condition.
Because engine oil deteriorates over
time, there are cases when it is neces-
sary to change the engine oil before
the engine oil change reminder light
comes on. In these cases, change the
engine oil and oil filter according to the
maintenance schedule. (For engine oil
maintenance intervals, see the separate
“Toyota Service Booklet” or “Toyota
Warranty Booklet”.)
Dyna100/150_EE
Odometer and two trip
metersOil maintenance management
system

GAUGES, METERS AND SERVICE REMINDER INDICATORS71
ENGINE OIL CHANGE REMINDER LIGHT
This light comes on when the engine
switch is turned to the “ON” position. It
goes out after about 3 seconds. This indi-
cates that the system is functioning nor-
mally. If the light illuminates for 3 seconds
and then flashes for about 12 seconds,
this indicates that the time to change the
engine oil is approaching.
If this light stays on this warns you to
change the engine oil and oil filter us-
ing appropriate replacements at your
earliest convenience. For more informa-
tion about oil grade and viscosity, see
“Checking the engine oil level” on page
188 in Section 7−2.
After changing the engine oil and oil filter,
be sure to reset the system, so that the
light goes out. (For instructions on reset-
ting the system, see “RESETTING THE
SYSTEM” on page 72 in this Section.)
The system must also be reset if an en-
gine oil and oil filter change is performed
before the light comes on. If you do not
reset the system, it cannot inform you of
the correct time to change the engine oil
and oil filter.If any of the following occurs, the
system may not be functioning normal-
ly. Have the vehicle checked at any
authorized Toyota dealer or repairer, or
another duly qualified and equipped
professional.
DWhen the engine switch is turned to
the “ON” position, the light does not
come on.
DThe light flashes.
DAfter changing the engine oil and oil
filter, even though thesystem hasbeen
reset, the light does not go out, or
comes on again soon.
NOTICE
After changing the engine oil and oil
filter, be sure to reset the system.
(For instructions on resetting the sys-
tem, see “RESETTING THE SYSTEM”
on page 72 in this Section.) If you do
not reset the system, it cannot inform
you of the correct time to change the
engine oil and oil filter.
Dyna100/150_EE

72GAUGES, METERS AND SERVICE REMINDER INDICATORS
RESETTING THE SYSTEM
After an engine oil and oil filter
change, perform the following proce-
dure to reset the system.
1. Set the odometer and two trip meters
display to trip meter A with the engine
switch “ON” and turn the engine switch
to the “LOCK” position.
2. Turn the engine switch to the “ON”
position while pushing the trip meter
reset knob. At this time, do not start
the engine and keep pushing the reset
knob.
3. Release the reset knob more than one
second after the trip meter displays
“000000”. Thesystem is reset.
For the locations of odometer and two trip
meters and trip meter reset knob and the
procedure about trip meter A setting, see
“Odometer and two trip meters” on page
70.
The system must also be reset ifengine
oil and oil filter are changed before the
light comes on.
If the engine oil change reminder light
remains on after performing the above
procedure, repeat the procedure again.
NOTICE
Reset the system only after an engine
oil and oil filter change. If you reset
the system at any other time, it can-
not inform you of the correct time to
change the engine oil and oil filter.
Dyna100/150_EE

74GAUGES, METERS AND SERVICE REMINDER INDICATORS
If the indicator or
buzzer comes on...
Do this.
(l)Change the engine oil and oil filter.
(m)Light reminder
buzzerTurn off lights.
Dyna100/150_EE

78GAUGES, METERS AND SERVICE REMINDER INDICATORS
(j) Timing Belt Replacement Warning
Light
This light will come on every time when
the trip amount gets between 140000 km
and 150000 km in kilometer reading or
90000 miles in mile reading to indicate
that the timing belt should be replaced.
When it comes on, have the belt replaced
and the warning light reset by any autho-
rized Toyota dealer or repairer, or another
duly qualified and equipped professional.
NOTICE
Continued driving without having the
belt replaced will result in a broken
belt and engine damage.
(k) Fuel Filter Warning Light
The light warns you that the amount of
accumulated water in the fuel filter has
reached the specified level.
If it comes on, drain the water immediate-
ly. (See page 192 in Section 7−2for
instructions for how to drain the water.)
NOTICE
Never drive the vehicle with the warn-
ing light on. Continued driving with
water accumulated in the fuel filter
will damage the fuel injection pump.
(l) Engine Oil Change Reminder Light
This light comes on to remind you to
change the engine oil and oil filter.
If the light comes on, change the engine
oil and oil filter at your earliest conve-
nience. For detailed information, see “Oil
maintenance managementsystem” on
page 70 in this Section.(m) Light Reminder Buzzer
This buzzer will sound if the driver ’s door
is opened while the engine switch is
turned to the “LOCK” position with the
headlight switch on. Removing the key will
not stop the buzzer as long as the head-
light switch is on.
CHECKING SERVICE REMINDER
INDICATORS (except the low fuel level
warning light)
1. Apply the parking brake.
2. Turn the engine switch to the “ACC”
position.
The SRS warning light should come on.
It goes off after about 6 seconds.
3. Turn the engine switch to the “ON”
position, but do not start the engine.
All the service reminder indicators ex-
cept the SRS warning light should
come on. The “ABS” warning light goes
off after a few seconds. The engine oil
change reminder light goes off after
about 5 seconds.
If any service reminder indicator or warn-
ing buzzer does not function as described
above, have it checked by any authorized
Toyota dealer or repairer, or another duly
qualified and equipped professional, as
soon as possible.
Dyna100/150_EE

DO−IT−YOURSELF MAINTENANCE: Introduction185
If you perform maintenance by yourself,
be sure to follow the correct procedure
given in this Section.
You should be aware that improper or in-
complete servicing may result in operating
problems.
This Section gives instructions only for
those items that are relatively easy for an
owner to perform. As explained in Section
6, there are still a number of items that
must be done by a qualified technician
with special tools.
Utmost care should be taken when work-
ing on your vehicle to prevent accidental
injury. Here are a few precautions that
you should be especially careful to ob-
serve:
CAUTION
DWhen the engine is running, keep
hands, clothing, and tools away
from the moving fan and engine
drive belts. (Removing rings,
watches, and ties is advisable.)
DRight after driving, the engine
compartment—the engine, radiator,
exhaust manifold and power steer-
ing fluid reservoir, etc.—will be hot.
So be careful not to touch them.
Oil and fluids may also be hot.
DIf the engine is hot, do not remove
the radiator cap or loosen the drain
plugs to prevent burning yourself.
DDo not leave anything that may
burn easily, such as paper or rags,
in the engine compartment.
DDo not smoke, cause sparks or al-
low open flames around fuel or the
battery. Their fumes are flammable.
DBe extremely cautious when work-
ing on the battery. It contains poi-
sonous and corrosive sulfuric acid.
DDo not get under your vehicle with
just the body jack supporting it. Al-
ways use automotive jack stands or
other solid supports.
DBe sure that the engine switch is
off if you work near the electric
cooling fans. With the engine
switch on, the electric cooling fans
will automatically start to run if the
engine coolant temperature is high
and/or the air conditioning is on.
DUse eye protection whenever you
work on or under your vehicle
where you may be exposed to flying
or falling material, fluid spray, etc.
DUsed engine oil contains potentially
harmful contaminants which may
cause skin disorders such as in-
flammation or skin cancer, so care
should be taken to avoid prolonged
and repeated contact with it. To re-
move used engine oil from your
skin, wash thoroughly with soap
and water.
DDo not leave used oil within the
reach of children.
DDispose of used oil and filter only
in a safe and acceptable manner.
Do not dispose of used oil and fil-
ter in household trash, in sewers or
onto the ground. Call your dealer or
a service station for information
concerning recycling or disposal.
DTake care when filling the brake and
clutch fluid reservoirs because
brake fluid can harm your hands or
eyes. If fluid gets on your hands or
in your eyes, flush the affected area
with clean water immediately. If you
still feel uncomfortable with your
hands or eyes, go to the doctor.
Dyna100/150_EE
Do−it−yourself service
precautions

DO−IT−YOURSELF MAINTENANCE: Engine and Chassis187
Section 7−2
DO−IT−YOURSELF MAINTENANCE
Engine and Chassis
DChecking the engine oil level 188........................
DChecking the engine coolant level 190...................
DChecking the radiator, condenser and intercooler 192.....
DDraining fuel filter water 192............................
DChecking tire inflation pressure 193.....................
DChecking and replacing tires 194........................
DRotating tires 195......................................
DInstalling snow tires and chains 196.....................
DReplacing wheels 197..................................
Dyna100/150_EE

216SPECIFICATIONS
ENGINE
Valve clearance (engine cold), mm (in.):
Intake 0.20—0.30 (0.008—0.012)
Exhaust 0.35—0.45 (0.014—0.018)
ENGINE LUBRICATION
Oil capacity (drain andrefill—reference

),
L (qt., Imp. qt.):
With filter 7.0 (7.4, 6.2)
Without filter 6.8 (7.2, 6.0)

: The engine oil capacity is a reference
quantity to be used when exchanging.
Warm up and turn off the engine, wait
more than 5 minutes, and check the oil
level on the dipstick.
“Toyota Genuine Motor Oil” is used in
your Toyota vehicle. Toyota recommends
the use of approved “Toyota Genuine
Motor Oil”. Another motor oil of matching
quality can also be used.
Oil grade:
ACEA C2
NOTICE
Using engine oil other than ACEA C2
may damage the catalytic converter.
Recommended viscosity (SAE):
Temperature range anticipated before
next oil change
Preferred
Please contact any authorized Toyota
dealer or repairer, or another duly quali-
fied and equipped professional, for further
details.
COOLING SYSTEM
Total capacity, L (qt., Imp. qt.):
With front and rear heaters
11.5 (12.2, 10.1)
With front heater 10.7 (11.3, 9.4)
Coolant type:
Your Toyota vehicle is filled with “Toyota
Super Long Life Coolant” at the factory.
In order to avoid technical problems,
only use “Toyota Super Long Life
Coolant” or similar high quality ethylene
glycol based non−silicate, non−amine,
non−nitrite, and non−borate coolant with
long−life hybrid organic acid technology.
(Coolant with long−life hybrid organic
acid technology is a combination of low
phosphates and organic acids.)
Do not use plain water alone.
Please contact any authorized Toyota
dealer or repairer, or another duly quali-
fied and equipped professional, for fur-
ther details.
BATTERY
Specific gravity reading at 20_C(68_F):
1.250—1.290 Fully charged
1.160—1.200 Half charged
1.060—1.100 Discharged
Charging rates:
Quick charge 15 A max.
Slow charge 5 A max.
CLUTCH
Pedal free play, mm (in.):
5—18 (0.2—0.7)
Fluid type:
SAE J1703 or FMVSS No.116 DOT 3
Dyna100/150_EE
Service specifications

222INDEX
A
Adding washer fluid 204..................
Adjustment
Driver ’s seat 25.......................
Seat belt 28...........................
Air bleeding 142.........................
Air conditioning filter 93..................
Air conditioningsystem 84...............
Airbag 38...............................
Anti−lock brake system
warning light 73.......................
Anti−theft steering column lock 80........
Appearance care
Cleaning the interior 173...............
Protecting your Toyota from
corrosion 170.......................
Washing and waxing 171...............
Auxiliary box 102........................
B
Battery
Access 182...........................
Checking battery condition 200.........
Gas caution 200.......................
Handling safety 200...................
Recharging precautions 202............
Winter driving tips 129.................
Before starting the engine 124............
Brake pad wear indicators 119............
Brake system 116.......................
Brake system warning light 73............
Brakes
Pad wear indicators 119................
Parking 82............................
Break−in tips 108........................
C
Carbon monoxide caution 114............
Card holder 104.........................
Center console box 103..................
Charging system warning light 73.........
Checking and replacing fuses 203........
Checking the engine oil level 188.........
Checking the radiator, condenser and
intercooler 192........................Child restraint
Child restraint system 45...............
Installation 48,51......................
Precautions 44........................
Types of child restraint system 46.......
Cigarette lighter and ashtrays 100........
Cleaning the interior 173.................
Cold weather
Operation 129.........................
Condenser
Checking the condenser 192...........
Controls, Instrument panel 2,6...........
Cooling system
Coolant level 190......................
Engine overheating 148................
Radiator and reservoir 190.............
Radiator cap 148......................
Winter driving tips 129.................
Corrosion prevention 170................
Cup holder 102..........................
D
Diesel particulate filter system 110........
Differential, Limited slip 120..............
Dimmer switch, Headlight 62.............
Directional signals 62....................
Do−it−yourself maintenance
Service precautions 185...............
Does your vehicle need repairing? 177....
Doors
Side doors 13.........................
DPF system 110.........................
Driver ’s seat 25.........................
Driving
Driving tips 124........................
Manual transmission 81................
Driving in the rain 128....................
Driving tips
Driving in the rain 128..................
Driving tips in various conditions 127....
Driving with a manual
transmission 81.....................
Economical driving 138................
Good driving practice 81...............
Pre−trip safety check 126..............
Winter driving tips 129.................
During
Break−in 108..........................
Dyna100/150_EE