TOYOTA FJ CRUISER 2007 1.G Owners Manual

Page 171 of 340

1612007 FJ CRUISER from Oct. ’06Prod. (OM35873U)
XM satellite radio∗—
To select a preset channel, push the “ ”
or “ ” side of the switch. Repeat until a
desired channel is found.
∗: Use of satellite radio r equires XM
tuner and service. Contact your Toyota
dealer for details.
Compact disc player
Use this switch to skip up or down to a
different track in either direction.
Quickly push and release the “ ” or “ ”
side of the switch until the track you want
to listen to is set. If you want to return
to the beginning of the current track, push
the “ ” side of the switch once, quickly.
With compact disc changer only—
Push and hold the “ ” or “” side of the
switch until the disc you want to listen to
is set.
MP3/WMA player
Use this switch to select a desired file or
disc.
To select a desired file:
Quickly push and release the “ ” or “ ”
side of the switch until the file you want
to listen to is set. If you want to return
to the beginning of the current file, push
the “ ” side of the switch once, quickly. To select a desired disc:
Push and hold the “
” or “ ” side of the
switch until the disc you want to listen to
is set.
3. “MODE” switch
Push the “MODE” switch to select an au-
dio mode. Each push changes the mode
sequentially if the desired mode is ready
to use.
To turn the audio system on, push the
“MODE” switch.
To turn the audio system off, push and
hold the “MODE” switch until the system
turns off.TS18005a
An AUX adapter is installed on the in-
strument panel.
By inserting a mini plug into the AUX
adapter, you can listen to music from a
portable audio device through the vehicle’s
speaker system.
To use the AUX adapter, switch to the
AUX mode (external device mode) by
pressing the “DISC·AUX” button. When the
AUX adapter is in use, “AUX” will appear
on the display. To adjust the volume, turn
the “PWR·VOL” knob.
If you install an audio system other than
a genuine audio system, you will not be
able to use the AUX adapter.
AUX adapter

Page 172 of 340

1622007 FJ CRUISER from Oct. ’06Prod. (OM35873U)
TS18008
To operate the sub woofer, push the
sub woofer onoff switch.
To stop it, push the switch again.
NOTICE
To ensure correct audio/video system
operation:
Be careful not to spill beverages
over the audio system.
 Do not put anything other than a
compact disc into the slot.
 The use of a cellular phone inside
or near the vehicle may cause a
noise from the speakers of the au-
dio system which you are listening
to. However, this does not indicate
a malfunction.
RADIO RECEPTION
Usually, a problem with radio reception
does not mean there is a problem with
your radio—it is just the normal result of
conditions outside the vehicle. For example, nearby buildings and terrain
can interfere with FM reception. Power
lines or telephone wires can interfere with
AM signals. And of course, radio signals
have a limited range. The farther you are
from a station, the weaker its signal will
be. In addition, reception conditions
change constantly as your vehicle moves.
Here are some common reception prob-
lems that probably do not indicate a prob-
lem with your radio:
FM
Fading and drifting stations—Generally, the
effective range of FM is about 40 km (25
miles). Once outside this range, you may
notice fading and drifting, which increase
with the distance from the radio transmit-
ter. They are often accompanied by distor-
tion.
Multi
−path—FM signals are reflective,
making it possible for two signals to reach
your antenna at the same time. If this
happens, the signals will cancel each oth-
er out, causing a momentary flutter or
loss of reception.
Sub woofer (on some models) Audio system operating hints

Page 173 of 340

1632007 FJ CRUISER from Oct. ’06Prod. (OM35873U)
Static and fluttering—These occur when
signals are blocked by buildings, trees, or
other large objects. Increasing the bass
level may reduce static and fluttering.
Station swapping—If the FM signal you
are listening to is interrupted or weak-
ened, and there is another strong station
nearby on the FM band, your radio may
tune in the second station until the origi-
nal signal can be picked up again.
AM
Fading—AM broadcasts are reflected by
the upper atmosphere—especially at night.
These reflected signals can interfere with
those received directly from the radio sta-
tion, causing the radio station to sound
alternately strong and weak.
Station interference—When a reflected sig-
nal and a signal received directly from a
radio station are very nearly the same
frequency, they can interfere with each
other, making it difficult to hear the broad-
cast.
Static—AM is easily affected by external
sources of electrical noise, such as high
tension power lines, lightening, or electri-
cal motors. This results in static.XM∗
Alternation or modifications carried out
without appropriate authorization may in-
validate the user ’s right to operate the
equipment.
∗: Use of satellite radio requires XM
tuner and service. Contact your Toyota
dealer for details.
NOTICE
This equipment has been tested and
found to comply with the limits for a
class B digital device, pursuant to
Part 15 of the FCC Rules. These lim-
its are designed to provide reasonable
protection against harmful interfer-
ence in a residential installation. This
equipment generates, uses and can
radiate radio frequency energy and, if
not installed and used in accordance
with the instructions, may cause
harmful interference to radio commu-
nications. However, there is no guar-
antee that interference will not occur
in a particular installation.
If this equipment does cause harmful
interference to radio or television re-
ception, which can be determined by
turning the equipment off and on, the
user is encouraged to try to correct
the interference by one or more of
the following measures:
—Reorient or relocate the receiving
antenna.
—Increase the separation between the
equipment and receiver.
—Connect the equipment into an out-
let on a circuit different from that to
which the receiver is connected.
—Consult the dealer or an experi-
enced radio/TV technician for help.

Page 174 of 340

1642007 FJ CRUISER from Oct. ’06Prod. (OM35873U)
CARING FOR YOUR COMPACT DISC
PLAYER AND DISCS
Extremely high temperatures can keep
your compact disc player from working.
On hot days, use the air conditioning
to cool the vehicle interior before you
listen to a disc.
Bumpy roads or other vibrations may
make your compact disc player skip.
If moisture gets into your compact disc
player, you may not hear any sound
even though your compact disc player
appears to be working. Remove the
disc from the player and wait until it
dries.
CAUTION
Compact disc players use an invisible
laser beam which could cause hazard-
ous radiation exposure if directed
outside the unit. Be sure to operate
the player correctly.
TS18009
Compact disc player
Use only compact discs marked as
shown above. The following products
may not be playable on your compact
disc player.
Copy−protected CD
CD− R (CD −Recordable)
CD− RW (CD −Re −writable)
CD− ROM
Z17038
Special shaped discs
Z17058
Transparent/tr anslucent discs

Page 175 of 340

1652007 FJ CRUISER from Oct. ’06Prod. (OM35873U)
Z17039
Low quality discs
Z17037
Labeled discs
NOTICE
Do not use special shaped, trans-
parent/translucent, low quality or la-
beled discs such as those shown in
the illustrations. The use of such
discs may damage the player or
changer, or it may be impossible to
eject the disc.
 This system is not designed for use
of dual discs. Do not use dual
discs because it may cause damage
to the player or changer.
Z17052
Correct Wrong
Handle the discs carefully, especially
when you are inserting them. Hold
them on the edge and do not bend
them. Avoid getting fingerprints on
them, particularly on the shiny side.
Dirt, scratches, warping, pin holes, or
other disc damage could cause the
player to skip or to repeat a section of
a chapter or track. (To see a pin hole,
hold the disc up to the light.)
Remove discs from the compact disc
player when you are not playing them.
Store them in their plastic cases away
from moisture, heat, and direct sun-
light.

Page 176 of 340

1662007 FJ CRUISER from Oct. ’06Prod. (OM35873U)
Z17053
To clean a disc: Wipe it with a soft, lint−
free cloth that has been dampened with
water. Wipe in a straight line from the
center to the edge of the disc (not in
circles). Dry it with another soft, lint −free
cloth. Do not use a conventional record
cleaner or anti −static device. MP3/WMA FILES
MP3 is short for MPEG Audio Layer 3
and refers to an audio compression
technology standard.
WMA is short for Windows MediaTM
Audio. WMA is able to compress audio
data to about 1/2 the level of MP3.
The MP3/WMA player allows playback
of MP3/WMA files on CD
−ROM, CD −R
and CD −RW discs.
Disc recordings compatible with level 1
and level 2 of ISO 9660 and with the
Romeo and Joliet file system can be
played back.
When naming a MP3/WMA file, add the
corresponding filename extension
(.mp3/.wma).
The MP3/WMA player plays back files
with the file name extension
(.mp3/.wma) as an MP3/WMA file. To
prevent noise and malfunctions, do not
use this extension for files other than
MP3/WMA files.
It is possible to play back multi −ses-
sion compatible recorded discs.
When playing discs with MP3/WMA
files and audio data (CD −DA) such as
CD− EXTRA and MIXED− MODE CD,
CD− DA only can be played.
Files are compatible with the ID3 Tag
Ver. 1.0, Ver. 1.1, Ver. 2.2 and Ver. 2.3
formats for display of album (disc title),
track (track title) and artist (track art-
ist).
Files are compatible with the WMA Tag
for display of track (track title) and
artist (track artist).
Only when MP3/WMA files of 32, 44.1
and 48 kHz frequencies are played
back, the emphasis function is valid.
(MP3 files: 16, 22.05, 24 kHz sampling
frequencies can be played back.)

Page 177 of 340

1672007 FJ CRUISER from Oct. ’06Prod. (OM35873U)
The sound quality of MP3/WMA files
generally becomes better with higher
bit rates. This product can play record-
ings with bit rates as follows:MP3 files: 64 kbps to 320 kbps
WMA files: 48 kbps to 320 kbps
But in order to be able to enjoy a
certain sound quality, it is recom-
mended to use only discs recorded
with a bit rate of at least 128 kbps.
The MP3/WMA player does not play
back MP3/WMA files from discs record-
er using packet write data transfer
(UDF format). Discs should be re-
corded using “pre −mastering” software
rather than packet −write software.
There is no m3u playlist compatibility.
There is no compatibility with the MP3i
(MP3 interactive) or mp3PRO format.
The MP3/WMA player is compatible
with VBR (Variable Bit Rate).
When playing back files recorded as
VBR (Variable Bit Rate) files, the play
time will not be correctly displayed if
fast −forward or reverse operations are
used.
It is not possible to check folders that
do not include MP3/WMA files.
MP3 files in up to 8 tiers of folders
can be played back. However, there is
a delay in the start of playback on
discs with numerous tiers. For this rea-
son we recommend creating discs with
no more than 2 tiers.
It is possible to play back up to 255
files on one disc.
It is possible to play back up to 192
folders on one disc.
18i023
001
002
003
004
005
006
007
008
009
010
011 Folder 1
Folder 3 Folder
Folder 4
Folder 6 Folder 7
Folder 8 Folder 2
Folder 5
: MP3/WMA file

Page 178 of 340

1682007 FJ CRUISER from Oct. ’06Prod. (OM35873U)
The turn of play of the compact disc
having the structure shown on the left
is as follows:
001 002 . . . 011
The order changes depending on the
PC and MP3/WMA encoding software
you use. CDR and CDRW discs
CD−
R/CD− RW discs that have not been
subject to the “finalizing process” (a
process that allows them to be played
back on a conventional CD player)
cannot be played back.
It may not be possible to play back
CD− R/CD− RW discs recorded on a mu-
sic CD recorder or a personal comput-
er because of disc characteristics,
scratches or dirt on the disc, or dirt,
condensation, etc. on the lens of this
unit.
Playback of discs recorded on a per-
sonal computer may not be possible
depending on the application settings
and the environment. Record with the
correct format. (For details, contact the
manufacturer of the applications.)
Playback of CD −R/CD− RW discs may
become impossible in case of direct
exposure to sunlight, high tempera-
tures, or the storage conditions in the
vehicle.
Titles and other text information re-
corded on a CD −R/CD− RW disc may
not be displayed by the MP3/WMA
player (in the case of audio data (CD −
DA)).
The MP3/WMA player conforms to the
track skip function of the CD −R/CD−
RW disc.
If you insert a CD −RW disc into the
MP3/WMA player, load time to play-
back will be longer than for a conven-
tional CD or CD −R disc.
Read the precautions accompanying
the CD −R/CD− RW discs before use.
Recordings on CD −R/CD− RW cannot
be played back using the DDCD
(Double Density CD) system.

Page 179 of 340

1692007 FJ CRUISER from Oct. ’06Prod. (OM35873U)
TERMS
Packet write—
This is a general term for a method of
writing on CD−R, etc. at the time required
for a file, just as is done with files on
floppy or hard di scs.
Bit rate—
This expresses data volume per second,
or bps units (bits per second). The higher
the rate, the more information is available
to reproduce the sound. Using the same
encoding methods (such as MP3/WMA),
the higher the rate, the better the sound.
Multisession—
Multi −session is a recording method that
allows additional data to be recorded later.
When recording data on a CD −ROM,
CD− R or CD −RW, etc., all data from be-
ginning to end is treated as a single unit
or session. Multi −session is a method of
recording more than 2 sessions in one
disc.
CDDA—
CD− DA is an abbreviation of Compact
Disc Digital Audio. It refers to the uncom-
pressed format of regular CDs. ID3 Tag—
This is a method of embedding track
−re-
lated information in an MP3 file. This em-
bedded information can include the track
title, the artist’s name, the album title, the
music genre, the year of production, com-
ments and other data. The contents can
be freely edited using software with ID3
tag editing functions. Although the tags
are restricted to the number of characters,
the information can be viewed when the
track is played back.
WMA Tag—
WMA files can contain a WMA tag that is
used in the same way as an ID3 tag.
WMA tags carry information such as track
title, artist name.
ISO 9660 format—
This is the international standard for the
format logic of CD −ROM folders and files.
For the ISO 9660 format, there are regula-
tions for the following two levels.
Level 1:
The file name is in 8.3 format (the name
consists of up to 8 characters, half −byte
English capital letters and half −byte nu-
merals and the “ −” sign, with a file exten-
sion of three characters.) Level 2:
The file name can have up to 31 (MP3
files)/15 (WMA files) characters (including
the separation mark “.” and a file exten-
sion). Each folder contains less than 8
hierarchies.
Extended formats
Joliet:
File name can have up to 64 characters.
Romeo:
File names can have up to 128 charac-
ters.
m3u—
Playlists created using the “WINAMP” soft-
ware have a playlist file extension (.m3u).
MP3—
MP3 is short for MPEG 1 & 2 Audio Layer
3. It is an audio compression standard set
by a working group (MPEG) of the ISO
(International Standards Organization).
MP3 is able to compress audio data to
about 1/10 the level of a conventional
disc.

Page 180 of 340

1702007 FJ CRUISER from Oct. ’06Prod. (OM35873U)
WMA—
WMA is short for Windows Media
TM Audio.
It is the audio file format developed by
Microsoft Corporation. WMA is able to
compress audio data to about 1/2 the lev-
el of MP3. The decoding formats for WMA
files are Ver7, 8, and 9.
Windows Media
TM and Windows are reg-
istered trademarks of Microsoft Corpora-
tion in the United States and other coun-
tries.

Page:   < prev 1-10 ... 131-140 141-150 151-160 161-170 171-180 181-190 191-200 201-210 211-220 ... 340 next >