tow TOYOTA FJ CRUISER 2007 1.G Owners Manual

252007 FJ CRUISER from Oct. ’06Prod. (OM35873U)
TS12022
This indicates that the fuel filler door
is on the left side of your vehicle.
TS12023
1. To open the fuel filler door, pull thedoor toward out as shown.
When refueling, turn off the engine.
CAUTION
Do not smoke, cause sparks or allow
open flames when refueling. The
fumes are flammable.
NOTICE
In order to prevent the fuel f iller door
from being damaged, do not apply ex-
cessive force.
TS12024a
2. To remove the fuel tank cap, turn the cap slowly counterclockwise,
then pause slightly before removing
it. After removing the cap, hang the
tether as shown in the illustration.
It is not unusual to hear a slight swoosh
when the cap is opened.
CAUTION
When opening the cap, do not remove
the cap quickly. In hot weather, fuel
under pressure could cause injury by
spraying out of the filler neck if the
cap is suddenly removed.
Fuel tank cap

282007 FJ CRUISER from Oct. ’06Prod. (OM35873U)
While the vehicle is being driven, all ve-
hicle occupants should have the seatback
upright, sit well back in the seat and prop-
erly wear the seat belts provided.
CAUTION
Do not drive the vehicle unless the
occupants are properly seated. Do
not allow any passengers to sit on
top of a foldeddown seatback, or
in the luggage compartment or car-
go area. Persons not properly
seated and/or not properly re-
strained by seat belts can be killed
or severely injured in the event of
emergency braking or a collision.
During driving, do not allow any
passengers to stand up or move
around between seats. Otherwise,
death or severe injuries can occur
in the event of emergency braking
or a collision.
Waterproof and water−repellent seats are
installed in your vehicle; however, the wa-
ter −repellent effect does not last forever. Driver seat
CAUTION
The SRS driver airbag deploys with
considerable force, and can cause
death or serious injury especially if
the driver is very close to the airbag.
The National Highway Traffic Safety
Administration (“NHTSA”) advises:
Since the risk zone for driver airbag
is the first 50—75 mm (2—3 in.) of
inflation, placing yourself 250 mm (10
in.) from your driver airbag provides
you with a clear margin of safety.
This distance is measured from the
center of the steering wheel to your
breastbone. If you sit less than 250
mm (10 in.) away now, you can
change your driving position in sever-
al ways:
Move your seat to the rear as far
as you can while still reaching the
pedals comfortably.
Slightly recline the back of the
seat. Although vehicle designs vary,
many drivers can achieve the 250
mm (10 in.) distance, even with the
driver seat all the way forward, sim-
ply by reclining the back of the
seat somewhat. If reclining the back
of your seat makes it hard to see
the road, raise yourself by using a
firm, nonslippery cushion, or raise
the seat if your vehicle has that
feature.
If your steering wheel is adjustable,
tilt it downward. This points the air-
bag toward your chest instead of
your head and neck.
The seat should be adjusted as rec-
ommended by NHTSA above, while
still maintaining control of the foot
pedals, steering wheel, and your view
of the instrument panel controls.
Seats Front seats—
—Front seat precautions

312007 FJ CRUISER from Oct. ’06Prod. (OM35873U)
CAUTION
Avoid reclining the seatback any
more than needed. The seat belts pro-
vide maximum protection in a frontal
or rear collision when the driver and
the front passenger are sitting up
straight and well back in the seats. If
you are reclined, the lap belt may
slide past your hips and apply re-
straint forces directly to the abdomen
or your neck may contact the shoul-
der belt. In the event of a frontal
collision, the more the seat is re-
clined, the greater the risk of death
or personal injury.
TS13004a
BEFORE FOLDING DOWN REAR SEAT
Stow the rear seat belt buckles as
shown in the illustration.
This prevents the seat belt buckles from
falling out when you fold the seatback.
NOTICE
To prevent damage to the seat belt
buckles, the seat belt buckles must
be stowed before you fold the seat-
back.
TS13006
1. Remove the head restraint.
NOTICE
To prevent damage to the head re-
straints, the head restraints must be
removed before you fold down the
seatback.
Rear seats—
—Folding down rear seats

322007 FJ CRUISER from Oct. ’06Prod. (OM35873U)
TS13007a
2. Swing the bottom cushion up bypulling the lock rel ease strap.
Each bottom cushion can be swung up
separately.
TS13008
3. Push the lock release button and fold down the seatback.
This will enlarge the luggage compartment
as far as the raised seat cushion. See
“—Stowage precautions” on page 226 in
Section 2 for precautions when loading
luggage.
Each seatback can be folded separately
and the seat bottom cushions can be re-
moved. See “—Removing rear seat bottom
cushions” on page 33.
TS13009
WHEN RETURNING THE SEATBACK
If you cannot raise the seatback because
of the locked seat belt, do not try to force
it. Release the lock of the seat belt in the
following way. 1. Push in the lower front edge of the seatback to slacken the seat belt.
2. Let the seat belt retract a little.

332007 FJ CRUISER from Oct. ’06Prod. (OM35873U)
CAUTION
When returning seats to their original
position, observe the following pre-
cautions in order to prevent death or
serious injury in a collision or sud-
den stop:
Make sure the seatback is securely
locked by pushing forward and rear-
ward on the top of the seatback.
Failure to do so will prevent the
seat belt from operating properly.
Make sure the seat belts are not
twisted or caught in the seatback
and are arranged in their proper
position and are ready to use.
Make sure the bottom cushion is
securely locked by pulling up the
edge of the cushion.
Make sure the bottom cushion is
securely locked by pressing down
the cushion near the lock release
straps.
Make sure to arrange the buckles of
the seat belts in their proper posi-
tion and be ready to use.
TS13004a
BEFORE REMOVING REAR SEAT BOT-
TOM CUSHIONS
Stow the rear seat belt buckles as
shown in the illustration.
This prevents the seat belt buckles from
falling out when you fold the seatback.
NOTICE
To prevent damage to the seat belt
buckles, the seat belt buckles must
be stowed before you remove the rear
seat bottom cushion.
TS13007
1. Swing the bottom cushion up by pulling the lock rel ease strap.
—Removing rear seat bottom
cushions

402007 FJ CRUISER from Oct. ’06Prod. (OM35873U)
TS13015
To release the belt, press the buckle
release button and allow the belt to
retract.
If the belt does not retract smoothly, pull
it out and check for kinks or twists. Then
make sure it remains untwisted as it re-
tracts.
TS13004a
The rear seat belt buckles can be
stowed when not in use.
Seat belt buckle must be stowed before
you fold the seatback. (See “—Folding
down rear seats” on page 31 or
“—Removing rear seat bottom cushions”
on page 33 in this Section.)If your seat belts cannot be fastened se-
curely because they are not long enough,
a personalized seat belt extender is avail-
able from your Toyota dealer free of
charge.
Please contact your local Toyota dealer so
that the dealer can order the proper re-
quired length for the extender. Bring the
heaviest coat you expect to wear for prop-
er measurement and selection of length.
Additional ordering information is available
at your Toyota dealer.CAUTION
When using the seat belt extender,
observe the following precautions.
Failure to follow these instructions
could reduce the effectiveness of the
seat belt restraint system in case of
an accident, increasing the chance of
death or serious injury.
Remember that the extender pro-
vided for you may not be safe when
used on a different vehicle, for
another person, or at a different
seating position than the one origi-
nally intended.
—Stowing rear seat belt
buckles
—Seat belt extender

842007 FJ CRUISER from Oct. ’06Prod. (OM35873U)
TS14001
To change the steering wheel angle,
hold the steering wheel, pull the lock
release lever toward you, tilt the steer-
ing wheel to the desired angle and re-
lease the lever.
When the steering wheel is in a low posi-
tion, it will spring up as you release the
lock release lever.
CAUTION
Do not adjust the steering wheel
while the vehicle is moving. Doing
so may cause the driver to mishan-
dle the vehicle and an accident may
occur resulting in death or serious
injuries.
After adjusting the steering wheel,
try moving it up and down to make
sure it is locked in position.
TS14002
Adjust the mirror so that you can just
see the side of your vehicle in the mir-
ror.
Be careful when judging the size or dis-
tance of any object seen in the outside
rear view mirror on the passenger ’s side
because it is a convex mirror. Any object
seen in a convex mirror will look smaller
and farther away than when seen in a flat
mirror.
Tilt steering wheelOutside rear view mirrors—

952007 FJ CRUISER from Oct. ’06Prod. (OM35873U)
To squirt washer fluid, pull the lever
toward you.
If the windshield wipers are off, they will
operate a couple of times after the washer
squirts.
For instructions on adding washer fluid,
see “Adding washer fluid” on page 309 in
Section 7−3.
In freezing weather, warm the windshield
with the defroster before using the washer.
This will help prevent the washer fluid
from freezing on your windshield, which
can block your vision.
NOTICE
Do not operate the wipers if the wind-
shield is dry. It may scratch the
glass.
When waxing your vehicle, make sure that
the washer nozzles do not become
blocked. If a nozzle becomes blocked,
contact your Toyota dealer to have the
vehicle serviced.
NOTICE
If a nozzle becomes blocked, do not
try to clear it with a pin or other
object. The nozzle will be damaged.
TS15009
To turn on the back window wiper, twist
the lever knob upward.
The key must be in the “ON” position.
Lever position
Speed setting
Position 1Intermittent
Position 2Normal
In Position 1, the wiper operates 3 times
at normal speed and then moves to inter-
mittent mode.
To squirt washer fluid on the back window,
twist the knob upward or downward as far
as it will go (position 3 or 4). The knob
automatically returns from these positions
after you release it. The back window wip-
er operates while the washer squirts. For instructions on adding washer fluid,
see “Adding washer fluid” on page 309 in
Section 7
−3.
If the back window is not securely closed,
the back window wiper and washer will
not work. Make sure the back window is
securely closed when using the back win-
dow wiper and washer.
NOTICE
Do not operate the back window wip-
er if the back window is dry. It may
scratch the glass.
Back window wiper and
washer

992007 FJ CRUISER from Oct. ’06Prod. (OM35873U)
Idling for a long period with the air
conditioning on in stop−and− go traffic.
Towing a trailer.
NOTICE
Do not remove the thermostat in
the engine cooling system as this
may cause the engine to overheat.
The thermostat is designed to con-
trol the flow of coolant to keep the
temperature of the engine within
the specified operating range.
 Do not continue driving with an
overheated engine. See “If your ve-
hicle overheats” on page 252 in
Section 4.TS16005
The voltmeter tells whether the battery
is charged or discharged. Check it
while the engine is running—the needle
should always indicate as shown above.
If the needle reads below or above the
normal range while the engine is running,
it indicates the charging system needs im-
mediate repair.
However, it is normal for the needle to
drop below the normal range during en-
gine starting.
TS16003
The tachometer indicates engine speed
in thousands of rpm (revolutions per
minute). Use it while driving to select
correct shift points and to prevent en-
gine lugging and overrevving.
Driving with the engine running too fast
causes excessive engine wear and poor
fuel economy. Remember, in most cases
the slower the engine speed, the greater
the fuel economy.
Voltmeter Tachometer

11 62007 FJ CRUISER from Oct. ’06Prod. (OM35873U)
(b) Normal driving1. Start the engine as instructed in “How to start the engine” on page 232 in
Section 3. The transmission must be in
“P” or “N”.
Four −wheel drive models—
When the four −wheel drive control lever is
in “L4” (low −speed position, four −wheel
drive), the driving pattern selector setting
has no effect on gear shift timing. (See
“Four −wheel drive system (part −time four −
wheel drive models)” on page 120 in this
Section for information of the four −wheel
drive control lever.)
2. With your foot holding down the brake pedal, shift the selector lever to “D”.
When the lever is in the “D” position, the
automatic transmission system will select
the most suitable gear for running condi-
tions such as normal cruising, hill climb-
ing, hard towing, etc.
Tw o −wheel drive models—
Always use the “D” position for better fuel
economy and quieter driving. If the engine
coolant temperature is low, the transmis-
sion will not shift into the overdrive gear
even in the “D” position. Four
−wheel drive models—
Always use the “D” position for better fuel
economy and quieter driving. If the engine
coolant temperature is low or when the
four −wheel drive control lever is in “L4”
(low −speed position, four −wheel drive), the
transmission will not shift into the over-
drive gear even in the “D” position. (See
“Four −wheel drive system (part −time four −
wheel drive models)” on page 122 in this
Section for information of the four −wheel
drive control lever.)
CAUTION
Never put your foot on the accelera-
tor pedal while shifting.
3. Release the parking brake and brake
pedal. Depress the accelerator pedal
slowly for smooth starting.
In normal cruising, the vehicle will start in
first gear and automatically shift up to the
most suitable gear. On inclines, declines
or winding roads, etc., the vehicle shifts
up and down automatically according to
the running conditions to obtain the suit-
able driving power and engine braking. If you need to accelerate rapidly while
driving, depress the accelerator pedal to
the full throttle position. This provides
more acceleration by automatically down-
shifting the transmission to the next lower
gear or beyond, depending on the vehicle
speed.
If engine braking is needed, such as in
descending a long h
ill, see “(c) Using
engine braking”.
AI (Artificial Intelligence) shifting control
AI shifting control selects the most suit-
able shift range automatically according to
the driver ’s operation and driving condi-
tion.
AI shifting control operates automatically
with the selector lever in the “D” position.
Shifting control on the slope: On inclines,
you can drive smoothly with reduced shift-
ing quantity. On declines, the vehicle will
shift down automatically to obtain optimum
engine braking and reduce the driver ’s
foot braking load.
Automatic shifting point change control:
The automatic shifting point control is con-
trolled in the following way to respond to
the driver ’s operation.