TOYOTA GT86 2016 Owners Manual (in English)

5
431 5-2. Steps to take in an emergency
When trouble arises
FT86_EE
CAUTION
■If the engine has to be turned off while driving
●Power assist for the brakes and steering wheel will be lost, making the
brake pedal harder to depress and the steering wheel heavier to turn.
Decelerate as much as possible before turning off the engine.
●Vehicles without a smart entry & start system: Never attempt to remove
the key, as doing so will lock the steering wheel.
Vehicles with a smart entry &
start system: To stop the
engine, press and hold the
“ENGINE START STOP”
switch for 2 consecutive sec-
onds or more, or press it
briefly 3 times or more in suc-
cession.
Stop the vehicle in a safe place by the road.
Press and hold for 2 seconds or more,
or press briefly 3 times or more
STEP 4
STEP 5
86_OM_EE_OM18058E.book 431 ページ ２０１５年３月１７日　火曜日　午前１１時３１分

432 5-2. Steps to take in an emergency
FT86_EE
86_OM_EE_OM18058E.book 432 ページ ２０１５年３月１７日　火曜日　午前１１時３１分

6Vehicle specifications
433
FT86_EE
6-1. Specifications
Maintenance data
(fuel, oil level, etc.).......... 434
Fuel information ................ 447
6-2. Customization
Customizable features ...... 449
86_OM_EE_OM18058E.book 433 ページ ２０１５年３月１７日　火曜日　午前１１時３１分

434
FT86_EE
6-1. Specifications
Maintenance data (fuel, oil level, etc.)
Dimensions and weight
*1: Unladen vehicle
*2: Vehicles without a front spoiler
*3: Vehicles with a front spoiler
*4: Vehicles without side skirts
*5: Vehicles with side skirts
Overall length4240 mm (166.9 in.)*2
4255 mm (167.5 in.)*3
Overall width1775 mm (69.9 in.)*4
1795 mm (70.6 in.)*5
Overall height*11320 mm (52.0 in.)
Wheelbase 2570 mm (101.2 in.)
TreadFront 1520 mm (59.8 in.)
Rear 1540 mm (60.6 in.)
Gross vehicle massDetails are described on the manufac-
turer’s label. (→P. 435)
Maximum permissi-
ble axle capacityFront 876 kg (1931 lb.)
Rear 943 kg (2079 lb.)
86_OM_EE_OM18058E.book 434 ページ ２０１５年３月１７日　火曜日　午前１１時３１分

435 6-1. Specifications
6
Vehicle specifications
FT86_EE
Vehicle identification
■Vehicle identification number
The vehicle identification number (VIN) is the legal identifier for
your vehicle. This is the primary identification number for your
Toyota. It is used in registering the ownership of your vehicle.
This number is stamped under
the right-hand front seat.
This number is located on the
top left of the body panel.
This number is also on the man-
ufacturer’s label.
86_OM_EE_OM18058E.book 435 ページ ２０１５年３月１７日　火曜日　午前１１時３１分

436 6-1. Specifications
FT86_EE■Engine number
The engine number is stamped on the engine block as shown.
86_OM_EE_OM18058E.book 436 ページ ２０１５年３月１７日　火曜日　午前１１時３１分

437 6-1. Specifications
6
Vehicle specifications
FT86_EE
Engine
Fuel
*: If unleaded gasoline with an octane rating of 98 RON is not available,
unleaded gasoline with an octane rating of 95 RON may be used with no
detriment to engine durability or driveability.
Model FA20
Ty p eHorizontally opposed, liquid cooled 4 cylinder,
four-stroke gasoline
Bore and stroke 86.0 × 86.0 mm (3.39 × 3.39 in.)
Displacement 1998 cm3 (121.93 cu.in.)
Drive belt tension Automatic adjustment
Fuel typeEU area:
Unleaded gasoline conforming to European stan-
dard EN228 only
Except EU area:
Unleaded gasoline only
Research octane num-
ber98 or higher*
Fuel tank capacity
(Reference)50 L (13.2 gal., 11.0 Imp. gal.)
86_OM_EE_OM18058E.book 437 ページ ２０１５年３月１７日　火曜日　午前１１時３１分

438 6-1. Specifications
FT86_EE
Lubrication system
*: The engine oil capacity is a reference quantity to be used when changing
the engine oil. Warm up and turn off the engine, wait more than 5 minutes,
and check the oil level on the dipstick.
■Engine oil selection
“Toyota Genuine Motor Oil” is used in your Toyota vehicle. Toyota rec-
ommends the use of approved “Toyota Genuine Motor Oil”. Another
motor oil of matching quality can also be used.
Oil grade:
0W-20 and 5W-30:
API grade SL “Energy-Conserving”, SM “Energy-Conserving”, SN
“Resource-Conserving” or ILSAC multigrade engine oil
Oil capacity
(Drain and refill 
reference*)
Without filter
With filter 5.2 L (5.5 qt., 4.6 Imp. qt.)
5.4 L (5.7 qt., 4.8 Imp. qt.)
86_OM_EE_OM18058E.book 438 ページ ２０１５年３月１７日　火曜日　午前１１時３１分

439 6-1. Specifications
6
Vehicle specifications
FT86_EERecommended viscosity (SAE):
SAE 0W-20 is filled into your
Toyota vehicle at manufacturing,
and the best choice for good fuel
economy and good starting in
cold weather.
If SAE 0W-20 oil is not available,
SAE 5W-30 oil may be used.
However, it should be replaced
with SAE 0W-20 at the next oil
change.
Oil viscosity (0W-20 is explained here as an example):
• The 0W in 0W-20 indicates the characteristic of the oil which allows
cold startability. Oils with a lower value before the W allow for easier
starting of the engine in cold weather.
• The 20 in 0W-20 indicates the viscosity characteristic of the oil when
the oil is at high temperature. An oil with a higher viscosity (one with a
higher value) may be better suited if the vehicle is operated at high
speeds, or under extreme load conditions.
Temperature range anticipated before
next oil change
Preferred
86_OM_EE_OM18058E.book 439 ページ ２０１５年３月１７日　火曜日　午前１１時３１分

440 6-1. Specifications
FT86_EEHow to read oil container labels:
Either or both API registered marks are added to some oil containers
to help you select the oil you should use.
API Service Symbol
Top portion: The oil quality desig-
nation by API (American Petro-
leum Institute) (SN)
Center portion: The SAE viscosity
grade (SAE 0W-20)
Lower portion: “Resource-Con-
serving” means that the oil has
fuel saving and environmental
protection.
ILSAC Certification Mark
The ILSAC (International Lubri-
cant Specification Advisory Com-
mittee) Certification Mark is
displayed on the front of the con-
tainer.
86_OM_EE_OM18058E.book 440 ページ ２０１５年３月１７日　火曜日　午前１１時３１分