TOYOTA HIGHLANDER 2019 Owners Manual (in English)

5617-3. Do-it-yourself maintenance
7
Maintenance and care
HIGHLANDER_U
Replace the light bulb, and
install the bulb base.
Align the 3 tabs on the light bulb
with the mounting and insert.
Turn and secure the bulb
base.
Shake the bulb base gently to
check that it is not loose, turn
the headlight low beams on
once and visually confirm that
no light is leaking through the
mounting.
Turn the cover clockwise and
install it.
For the right side only: Install the washer fluid tank.
5
6
7
8

5627-3. Do-it-yourself maintenance
HIGHLANDER_U■
Headlight high beams/daytime
running lights (if equipped)
Turn the bulb base counter-
clockwise.
Unplug the connector while
pressing the lock release.
Replace the light bulb, and
install the bulb base.
Align the 3 tabs on the light bulb
with the mounting, and insert.
Turn and secure the bulb
base.
Shake the bulb base gently to
check that it is not loose, turn
the headlights on once and visu-
ally confirm that no light is leak-
ing through the mounting.
1
2
3
4

5637-3. Do-it-yourself maintenance
7
Maintenance and care
HIGHLANDER_U■
Front turn signal lights/pa
rking lights (bulb type)
Remove the 2 clips and
remove the side cover.
Turn the bulb base counter-
clockwise.
Remove the light bulb.
Install by conducting and wi th the directions reversed.
Install the side cover and
then install the 2 clips.
1
2
3
432
5

5647-3. Do-it-yourself maintenance
HIGHLANDER_U■
Front side marker lights
Remove the 2 clips and
remove the side cover.
Turn the bulb base counter-
clockwise.
Remove the light bulb.
Install by conducting and wi th the directions reversed.
Install the side cover and
then install the 2 clips.
1
2
3
423
5

5657-3. Do-it-yourself maintenance
7
Maintenance and care
HIGHLANDER_U■
Front fog lights (bulb type)
Remove the 3 screws and
partly remove the fender
liner.
Unplug the connector while
pressing the lock release.
Turn the bulb base counter-
clockwise.
Install a new light bulb.
Align the 3 tabs on the light bulb
with the mounting and insert.
1
2
3
4

5667-3. Do-it-yourself maintenance
HIGHLANDER_U
Turn clockwise and secure
the bulb base.
Install the connector.
Shake the connector gently to
check that it is not loose, turn
the front fog lights on once and
visually confirm that no light is
leaking through the mounting.
When installing the fender liner, install by conducting with the
directions reversed.
Make sure that the fender liner is attached to the inside of th e bumper.
5
6
71

5677-3. Do-it-yourself maintenance
7
Maintenance and care
HIGHLANDER_U■
Rear turn signal lights
Open the back door and
remove the cover.
Insert a flathead screwdriver
into the cover and remove it as
shown in the illustration.
To prevent damaging the vehi-
cle, wrap the flathead screw-
driver with a tape.
Remove the 2 screws, and
remove the lamp assembly
by pulling it directly backward
from the rear of the vehicle.
Remove the wire harness.
Turn the bulb base counter-
clockwise.
1
2
3
4

5687-3. Do-it-yourself maintenance
HIGHLANDER_U
Remove the light bulb.
When installing the light bulb, install by conducting , and
with the directions reversed.
Install the lamp assembly
and then install the 2 screws.
Align the guide ( ) and pin
( ) on the lamp assembly with
the mounting when installing it.
Install the cover.
5
654
3
7
1
2
8

5697-3. Do-it-yourself maintenance
7
Maintenance and care
HIGHLANDER_U■
Back-up lights
Open the back door and
remove the cover.
Insert a flathead screwdriver or
similar into the hole at the top of
the cover and remove it as
shown in the illustration.
To prevent damaging the vehi-
cle, wrap the flathead screw-
driver with a tape.
Turn the bulb base counter-
clockwise.
Remove the light bulb.
When installing, reverse the steps listed.
1
2
3
4

5707-3. Do-it-yourself maintenance
HIGHLANDER_U■
License plate lights
Remove the lens.
Insert a properly sized screwdriver into the hole of the lens o n the inner
side and disengage the claw and pry the lens toward the outer s ide as
shown in the illustration.
To prevent damaging the vehicle, wrap the tip of the screwdriver with
tape.
Remove the light bulb.
When installing, reverse the steps listed.
1
2
3