TOYOTA IQ 2012 Owners Manual

371 4-3. Do-it-yourself maintenance
4
Maintenance and care
iQ_WE_74014E
*1: Vehicles without daytime running light system and automatic light off system
*2: Vehicles with daytime running light system or automatic light off system10TAIL NO.1
*110 AManual headlight leveling dial, front
position lights, tail lights, license
plate lights
(PANEL NO.2)*25 A Daytime running light system
11 DOOR NO.2 20 A Power windows
12 D/L NO.1 15 APower door lock system, main body
ECU
13 DOOR NO.1 30 A Power windows
14 CIG 15 A Power outlet
15 ACC 5 AOutside rear view mirrors, audio
system, shift lock control system,
main body ECU
16PA N E L
*1
5 AMeter, power management ECU(PANEL NO.1)*2Meter
17TAIL NO.2
*1
10 AFront position lights, tail lights,
license plate lights, rear fog light,
front fog lights, manual headlight
leveling dial, multiport fuel injection
system/sequential multiport fuel
injection system, instrument clus-
ter, windshield wiper ECU TA I L
*2
18 (FOG FR) 15 A Front fog lights
19 AM1 7.5 A ACC, starting system
20 STOP 10 AVehicle stability control system,
power management ECU, shift lock
control system, stop lights, multiport
fuel injection system/sequential
multiport fuel injection system
21 (D/L NO.2) 10 A Power door lock system
22 (SEAT-HTR) 15 A Seat heaters
FuseAmpereCircuit

372 4-3. Do-it-yourself maintenance
iQ_WE_74014E
After a fuse is replaced
If the lights do not turn on even after the fuse has been replaced, a bulb
may need replacement. (P. 373)
If the replaced fuse blows again, have the vehicle inspected by any
authorized Toyota dealer or repairer, or another duly qualified and
equipped professional.
If there is an overload in the circuits
The fuses are designed to blow, protecting the wiring harness from damage.
CAUTION
To prevent system breakdowns and vehicle fire
Observe the following precautions.
Failing to do so may cause damage to the vehicle, and possibly a fire or
injury.
Never use a fuse of a higher amperage rating than indicated, or use any
other object in place of a fuse.
Always use a genuine Toyota fuse or equivalent.
Never replace a fuse with a wire, even as a temporary fix.
Do not modify the fuse or the fuse box.
NOTICE
Before replacing fuses
Have the cause of electrical overload determined and repaired by any autho-
rized Toyota dealer or repairer, or another duly qualified and equipped pro-
fessional, as soon as possible.

373
4-3. Do-it-yourself maintenance
4
Maintenance and care
iQ_WE_74014E
Light bulbs
You may replace the following bulbs by yourself. The difficulty level
of replacement varies depending on the bulb. As there is a danger
that components may be damaged, we recommend that replacement
is carried out by any authorized Toyota dealer or repairer, or another
duly qualified and equipped professional.
Preparing for light bulb replacement
Check the wattage of the light bulb to be replaced. (P. 456)
Front bulb locations
Headlight
Front position
light
Front fog light (if equipped)
Front turn signal light

374 4-3. Do-it-yourself maintenance
iQ_WE_74014E
Replacing light bulbs
Headlight
Left side
Push the tab in and lift the lid off.
Rear bulb locations
Back-up light/rear fog light
(Left-hand drive vehicles) Rear turn signal lightTa i l / s t o p l i g h tLicense plate light
Back-up light/
rear fog light
(Right-hand
drive vehicles)

375 4-3. Do-it-yourself maintenance
4
Maintenance and care
iQ_WE_74014ETurn the cover clockwise.
Turn the bulb base counterclock-
wise.
Unplug the connector while
depressing the lock release.
When installing, reverse the steps listed.

376 4-3. Do-it-yourself maintenance
iQ_WE_74014ERight side
Pinch the latches and remove
the washer inlet from the
bracket.
Press the claw and remove
the washer inlet from the
bracket.
Turn the cover counterclockwise.

377 4-3. Do-it-yourself maintenance
4
Maintenance and care
iQ_WE_74014ETurn the bulb base counterclock-
wise.
Unplug the connector while
depressing the lock release.
When installing, reverse the steps listed.
Front fog lights (if equipped)
Remove the front spats bolts.

378 4-3. Do-it-yourself maintenance
iQ_WE_74014ERemove the fender liner clip.
Slide off the fender liner.
Unplug the connector while
depressing the lock release.
Turn the bulb counterclockwise.
When installing, reverse the steps listed.

379 4-3. Do-it-yourself maintenance
4
Maintenance and care
iQ_WE_74014EFront position lights
Turn the bulb base counterclock-
wise.
Remove the light bulb.
When installing, reverse the steps listed.

380 4-3. Do-it-yourself maintenance
iQ_WE_74014EFront turn signal lights
Turn the bulb base counterclock-
wise.
Remove the light bulb.
When installing, reverse the steps listed.