TOYOTA LAND CRUISER 1996 J80 Workshop Manual

EM−16
−
ENGINE MECHANICAL TIMING CHAIN
1996 LAND CRUISER (RM451U)
19. REMOVE CRANKSHAFT TIMING GEAR
HINT:
If necessary, remove the gear with SST.
SST 09950−40010 (09951 −04010, 09952−04010,
09953 −04020, 09954 −04010, 09955 −04060),
09950 −60010 (09951 −00350)
20. REMOVE CHAIN TENSIONER SLIPPER AND VIBRA- TION DAMPER
(a) Using a 10 mm hexagon wrench, remove the bolt and slip-
per.
(b) Remove the 2 bolts and damper.
21. REMOVE OIL JET
Remove the bolt and oil jet.
22. REMOVE CRANKSHAFT ROTOR
23. REMOVE OIL PUMP DRIVE SHAFT GEAR
24. REMOVE PUMP DRIVE SHAFT GEAR
If the pump drive shaft gear cannot be removed by hand, use
2 screwdrivers.
NOTICE:
Position shop rags as shown to prevent damage.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P04776
146.6 mm16 Links
EM1EA−01
P03876
−
ENGINE MECHANICAL TIMING CHAIN
EM−17
1996 LAND CRUISER (RM451U)
INSPECTION
1. INSPECT TIMING CHAIN AND TIMING GEARS
(a) Measure the length of 16 links with the chain fully
stretched.
Maximum chain elongation: 146.6 mm (5.772 in.)
If the elongation is greater than maximum, replace the chain.
HINT:
Make the same measurements pulling at 3 or more places se-
lected at random.
(b) Wrap the chain around the timing gear.
(c) Using vernier calipers, measure the timing gear diameter with the chain.
NOTICE:
Vernier calipers must contact the chain rollers for measur-
ing.
Minimum gear diameter (w/Chain):
Camshaft126.0 mm (4.961 in.)
Crankshaft65.4 mm (2.575 in.)
If the diameter is less than minimum, replace the chain and
gears.
2. INSPECT CHAIN TENSIONER SLIPPER AND VIBRA-TION DAMPER
Measure the chain tensioner slipper and vibration damper
wears. Maximum wear: 1.0 mm (0.039 in.)
If the wear is greater than maximum, replace the slipper and/or
damper.
3. INSPECT OIL JET
Check the oil jet for damage or clogging.
If necessary, replace the oil jet.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

EM1Q5−01
EM−18
−
ENGINE MECHANICAL TIMING CHAIN
1996 LAND CRUISER (RM451U)
REPLACEMENT
REPLACE CRANKSHAFT FRONT OIL SEAL (See page EM−99)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

EM1EB−01
−
ENGINE MECHANICAL TIMING CHAIN
EM−19
1996 LAND CRUISER (RM451U)
INSTALLATION
1. SET CRANKSHAFT
Turn the crankshaft until the set key on crankshaft facing down-
ward.
2. INSTALL PUMP DRIVE SHAFT GEAR
3. INSTALL OIL PUMP DRIVE SHAFT GEAR
(a) Apply a light coat of engine oil on the shaft portion of the
gear.
(b) Install the gear.
4. INSTALL CRANKSHAFT ROTOR
5. INSTALL OIL JET
Install the oil jet with the bolt. Torque: 20 N·m (200 kgf·cm, 14 ft·lbf)
6. INSTALL CHAIN TENSIONER SLIPPER AND VIBRA- TION DAMPER
(a) Install the damper with the 2 bolts.
Torque: 20 N·m (200 kgf·cm, 14 ft·lbf)
(b) Using a 10 mm hexagon wrench, install the slipper with the bolt.
Torque: 69 N·m (700 kgf·cm, 51 ft·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

EM−20
−
ENGINE MECHANICAL TIMING CHAIN
1996 LAND CRUISER (RM451U)
(c) Check that the slipper moves smoothly.
7. INSTALL CRANKSHAFT TIMING GEAR
NOTICE:
Be careful of the installation direction.
HINT:
If necessary, install the gear with SST.
SST 09636−20010
8. INSTALL TIMING CHAIN AND CAMSHAFT TIMING GEAR
(a) Install the timing chain on the camshaft timing gear with the bright link aligned with the timing mark on the cam-
shaft timing gear.
(b) Install the timing chain on the crankshaft timing gear with the other bright link aligned with the timing mark on the
crankshaft timing gear.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
ENGINE MECHANICAL TIMING CHAIN
EM−21
1996 LAND CRUISER (RM451U)
(c) Tie the timing chain with a cord as shown in the illustration
and make sure it doesn’t come loose.
9. INSTALL TIMING CHAIN COVER
(a) Remove any old packing (FIPG) material and be careful
not to drop any oil on the contact surfaces of the timing
chain cover and cylinder block.
Using a razor blade and gasket scraper, remove all
the old packing (FIPG) material from the gasket sur-
faces and sealing grooves.
Thoroughly clean all components to remove all the
loose material.
Using a non −residue solvent, clean both sealing
surfaces.
(b) Apply seal packing to the timing chain cover as shown in the illustration.
Seal packing: Part No. 08826−00080 or equivalent
Install a nozzle that has been cut to a 2 − 3 mm (0.08
− 0.12 in.) opening.
HINT:
Avoid applying an excessive amount to the surface.
Parts must be assembled within 5 minutes of ap-
plication. Otherwise the material must be removed
and reapplied.
Immediately remove nozzle from the tube and rein-
stall cap.
(c) Place 2 new O− rings in position on the timing chain cover.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

EM−22
−
ENGINE MECHANICAL TIMING CHAIN
1996 LAND CRUISER (RM451U)
(d) Engage the gear of the oil pump drive rotor with the gear
of the oil pump drive gear, and install the oil pump.
(e) Install the oil pump and drive belt adjusting bar with the 9 bolts and 2 nuts.
Torque: 21 N·m (210 kgf·cm, 15 ft·lbf)
HINT:
Each bolt length is indicated in the illustration.
Bolt A: 30 mm (1.18 in.)
Bolt B: 50 mm (1.97 in.)
Bolt C: 60 mm (2.38 in.)
(f) Remove the cord from the chain.
10. INSTALL DRIVE BELT IDLER PULLEY
Install the pulley with the bolt. Torque: 43 N·m (440 kgf·cm, 32 ft·lbf)
11. INSTALL CRANKSHAFT PULLEY
(a) Align the pulley set key with the key groove of the pulley, and slide on the pulley.
(b) Using SST, install and torque the pulley bolt.
SST 09213−58012, 09330 −00021
Torque: 412 N·m (4,200 kgf·cm, 304 ft·lbf)
12. INSTALL NO. 1 OIL PAN (See page LU−12)
13. INSTALL NO. 2 OIL PAN (See page LU−12)
14. INSTALL BOLTS HOLDING NO. 1 OIL PAN TO TRANS-
MISSION HOUSING
Install the 6 bolts. Torque: 72 N·m (730 kgf·cm, 53 ft·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
ENGINE MECHANICAL TIMING CHAIN
EM−23
1996 LAND CRUISER (RM451U)
15. INSTALL OIL LEVEL SENSOR
(a) Install a new gasket to the level sensor.
(b) Install the level sensor with the 4 bolts.
Torque: 5.4 N·m (55 kgf·cm, 48 in.·lbf)
16. CONNECT OIL COOLER PIPE BRACKET TO NO. 1 OIL
PA N
17. INSTALL CYLINDER HEAD (See page EM−54 )
NOTICE:
However, for the installation of the camshaft timing gear
and timing chain, follow the below procedure. Align the
blight link of the timing chain and camshaft timing gear
mark, and install them to the camshaft.
18. INSTALL WATER PUMP
Install a new gasket and water pump with the 4 bolts and 2 nuts.
Torque: 21 N·m (210 kgf·cm, 15 ft·lbf)
19. INSTALL RADIATOR PIPE
(a) Connect the No.2 radiator hose to the water inlet.
(b) Install the 2 nuts holding the radiator pipe to the No.1 oil
pan.
Torque: 21 N·m (210 kgf·cm, 15 ft·lbf)
20. INSTALL A/C COMPRESSOR AND BRACKET
(a) Install the A/C compressor bracket with the 5 bolts.
Torque: 37 N·m (375 kgf·cm, 27 ft·lbf)
(b) Install the A/C compressor with the 4 bolts. Torque: 25 N·m (250 kgf·cm, 18 ft·lbf)
(c) Install and adjust the drive belt (See page CH−2).
21. INSTALL RADIATOR (See page CO−16 )
22. FILL ENGINE WITH OIL
23. INSTALL ENGINE UNDER COVER
24. START ENGINE AND CHECK FOR LEAKS
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

EM1E2−01
EM−24
−
ENGINE MECHANICAL CYLINDER HEAD
527
Author: Date:
1996 LAND CRUISER (RM451U)
CYLINDER HEAD
COMPONENTS
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
ENGINE MECHANICAL CYLINDER HEAD
EM−25
528
Author: Date:
1996 LAND CRUISER (RM451U)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010