display TOYOTA LAND CRUISER 2010 J200 Navigation Manual

AUDIO/VIDEO SYSTEM
237

Setting the display mode
Pushing “SIZE” changes the display
modes sequentially as follows:
Normal → “Wide 1” →“Wide 2”
Adjusting the screen
Push “DISPLAY”.
Select the desired button to adjust col-
or, tone, contrast and brightness. After
adjusting the screen, touch “OK”.
— Changing other settings

AUDIO/VIDEO SYSTEM
238
“Color” “R”:
Strengthens the red color of the screen.
“Color” “G”:
Strengthens the green color of the screen.
“Tone” “+”: Strengthens the tone of the
screen.
“Tone” “”: Weakens the tone of the
screen.
“Contrast” “+”:
Strengthens the contrast of the screen.
“Contrast” “”:
Weakens the contrast of the screen.
“Brightness” “+”:
Brightens the screen.
“Brightness” “”:
Darkens the screen.Automatic closing of the rear dis-
play
Push “DISPLAY” .
If “Auto Close” is on, the display will auto-
matically close when the “ENGINE START
STOP” switch is turned to OFF mode.
The display will automatically open when
the “ENGINE START STOP” switch is
turned to ACCESSORY or IGNITION ON
mode.

AUDIO/VIDEO SYSTEM
239

Displaying the map screen
Push “MAP”
to display the map screen.
NOTICE
To ensure correct audio/video sys-
tem operations:
Be careful not to spill beverages
over the audio/video system.
Do not put anything other than an
appropriate discs into the DVD
changer.
The use of a cellular phone inside
or near the vehicle may cause a
noise from the speakers of the au-
dio/video system which you are lis-
tening to. However, this does not
indicate a malfunction.
Radio reception
Usually, a problem with radio reception
does not mean there is a problem with your
radio — it is just the normal result of condi-
tions outside the vehicle.
For example, nearby buildings and terrain
can interfere with FM reception. Power
lines or telephone wires can interfere with
AM signals. And of course, radio signals
have a limited range. The farther you are
from a station, the weaker its signal will be.
In addition, reception conditions change
constantly as your vehicle moves.
Here are some common reception prob-
lems that probably do not indicate a prob-
lem with your radio:
Audio/video system
operating hints

AUDIO/VIDEO SYSTEM
244
MP3/WMA FILES
MP3 (MPEG Audio Layer 3) and WMA
(Windows Media Audio) are audio
compression standards.
The MP3/WMA player can play MP3
and WMA files on CD −ROM, CD−R
and CD −RW discs.
The unit can play disc recordings com-
patible with ISO 9660 level 1 and level
2 and with the Romeo and Joliet file
system.
When naming an MP3 or WMA file, add
the appropriate file extension (.mp3 or
.wma).
The MP3/WMA player plays back files
with .mp3 or .wma file extensions as
MP3 or WMA files. To prevent noise
and playback errors, use the appropri-
ate file extensions.
The MP3/WMA player can play only
the first session using multi −session
compatible CDs.
MP3 player — MP3 files are compat-
ible with the ID3 Tag Ver. 1.0, Ver. 1.1,
Ver. 2.2, and Ver. 2.3 formats. The unit
cannot display disc title, track title and
artist name in other formats.
USB memory player — MP3 files are
compatible with the ID3 Tag Ver. 1.0,
Ver. 1.1, Ver. 2.2, Ver. 2.3 and Ver. 2.4
formats. The unit cannot track title and
artist name in other formats.
WMA files can contain a WMA tag that
is used in the same way as an ID3 tag.
WMA tags carry information such as
track title, artist name.
The emphasis function is available
only when playing MP3/WMA files re-
corded at 32, 44.1 and 48 kHz. Sampling frequency
MP3 files for MP3 player:
MPEG 1 LAYER 3 — 32, 44.1, 48 kHz
MPEG 2 LSF LAYER 3 — 16, 22.05, 24
kHz
MP3 files for USB memory:
MPEG 1 AUDIO LAYER 2, 3 — 32,
44.1, 48 kHz
MPEG 2 AUDIO LAYER 2, 3 — 16,
22.05, 24 kHz
MPEG 2.5 — 8, 11.025, 12 kHz
WMA files for WMA player:
Ver. 7, 8, 9 CBR — 32, 44.1, 48 kHz
WMA files for USB memory:
Ver. 9 — HIGH PROFILE 32, 44.1, 48
kHz
The sound quality of MP3/WMA files
generally
improves with higher bit rate-
s. In order to achieve a reasonable lev-
el of sound quality, discs recorded with
a bit rate of at least 128 kbps are rec-
ommended.
Playable bit rates
MP3 files for MP3 player:
MPEG1 LAYER3 — 64 to 320 kbps
MPEG2 LSF LAYER3 — 64 to 160
kbps
MP3 files for USB memory:
MPEG 1 AUDIO LAYER 2, 3 — 32 to
320 kbps
MPEG 2 AUDIO LAYER 2, 3 — 32 to
160 kbps
MPEG 2.5 — 32 to 160 kbps
WMA files for WMA player:
Ver. 7, 8 CBR — 48 to 192 kbps
Ver. 9 CBR — 48 to 320 kbps
WMA files for USB memory:
Ver. 9 CBR — 32 to 320 kbps
The MP3/WMA player does not play
back MP3/WMA files from discs re-
corder using packet write data transfer
(UDF format). Discs should be re-
corded using “pre −mastering” software
rather than packet− write software.

AUDIO/VIDEO SYSTEM
245

M3u playlists are not compatible with
the audio player.
MP3i (MP3 interactive) and MP3PRO
formats
are not compatible with the au-
dio player.
The player is compatible with VBR
(Variable Bit Rate).
When playing back files recorded as
VBR (Variable Bit Rate) files, the play
time will not be correctly displayed if
fast−forward or reverse operations are
used.
It is not possible to check folders that
do not include MP3/WMA files.
MP3/WMA files in folders up to 8 levels
deep can be played. However, the
start of playback may be delayed when
using discs containing numerous lev-
els of folders. For this reason, we rec-
ommend creating discs with no more
than two levels of folders.
6U5161aX
001.mp3
002.wma
Folder 1003.mp3
Folder 2
004.mp3
005.wma
Folder 3006.mp3
The play order of the compact disc with
the structure shown above is as fol-
lows:
001.mp3 002.wma . . . 006.mp3
MP3/WMA player—It is possible to
play up to 192 folders or 255 files on
one disc.
U S B me m o r y—It is possible to play up
to 999 folders, 255 files per folder or
65,025 files in device.
The order changes depending on the
PC and MP3/WMA encoding software
you use.

AIR CONDITIONING
250
Operations such as changing the air outlets or fan speed are carried out\
on the touch
screen. To display the air conditioning touch screen, push the “CLIMATE” button.
1Driver side temperature display
(In degrees Fahrenheit or Centi-
grade) 252. . . . . . . . . . . . . . . . . . . . .
2Air flow control touchscreen but-
tons 254
. . . . . . . . . . . . . . . . . . . . . .
3Rear air conditioning control
touchscreen button 257
. . . . . .
4Passenger side temperature dis-
play
(In degrees Fahrenheit or Centi-
grade) 252 . . . . . . . . . . . . . . . . . . . . .
5“4ZONE”
(Temperature setting mode change
touch−screen button) 253
. . . . . . . .
6“A/C” 256
. . . . . . . . . . . . . . . . . . . . .
7Fan speed control touchscreen
buttons 255
. . . . . . . . . . . . . . . . . . .
8Windshield wiper deicer button
Owner’s Manual
. . . . . . . . . . . . . . . .
9Air intake control button 256
. . . .
10“REAR” button
Owner’s Manual
. . . . . . . . . . . . . . . .
11Micro dust and pollen filter button
258
. . . . . . . . . . . . . . . . . . . . . . . . . . .
12Windshield air flow button
257
. . . . . . . . . . . . . . . . . . . . . . . . . . .
13“OFF” button 252
. . . . . . . . . . . . . .
14“AUTO” button 252
. . . . . . . . . . . .
15“CLIMATE” button
(Air conditioning operation screen
display button) 251 . . . . . . . . . . . . . .
Automatic air conditioning controls

AIR CONDITIONING
251
The automatic air conditioning auto-
matically maintains the set tempera-
ture.
In the automatic operation mode, the air
conditioning selects the most suitable fan
speed, air flow, air intake and turns on− off
the air conditioning according to the tem-
perature.
The “ENGINE START STOP” switch must
be in the IGNITION ON mode.
“CLIMATE”: Push this button to display
touch−screen buttons for automatic air
conditioning controls.
NOTICE
To prevent battery discharge, do not
leave the air conditioning system on
longer than necessary when the en-
gine is stopped.
By pushing the switch above, you can
operate the speech command system.
For the operation of the speech command
system and the list of commands, see
pages 44 and 47.

AIR CONDITIONING
254
SETTING OPERATION — manual con-
trol
When one of the manual control touch−
screen buttons is depressed while operat-
ing in automatic mode, the operation cor-
responding to the depressed button is set.
Other conditions continue to be adjusted
automatically.
If manual air flow selection is desired —The outlets from which air is delivered can
be selected manually by touching the
touch−screen button. The function of each
mode is as follows:
1Panel — Air flows mainly from the
instrument panel vents and rear
vents.
2Bilevel — Air flows from both the
floor vents, instrument panel vents
and rear vents.
When you set the temperature selec-
tor setting at about the middle in auto-
matic operation, warm air flows out of
the floor vents and relatively low−
temperature air flows out of the in-
strument panel vents and rear vents.
3Floor — Air flows mainly from the
floor vents and rear vents.
4Floor/windshield — Air flows mainly
from the floor vents, windshield vents
and rear vents.
The selected mode is highlighted.
The air flow shown on the display indicates
the following.
 Air flows to the upper body (Panel)
Depending on the rear air condition-
ing setting
Automatic air flow mode only

AIR CONDITIONING
258
To remove frost or exterior fog on the
windshield—
1. Push the upper side of the temperature
control button until maximum figure ap-
pears on the temperature display.
2. Push the windshield air flow button.
3. Touch “HI” of the air flow control to ob-
tain a maximum air flow.
4. Leave the air conditioning on −off con-
trol off.
When the windshield air flow button is
pushed while operating in automatic
mode, the air conditioning is set to operate
and the OUTSIDE AIR mode is set.
Touch “A/C” for dehumidified heating or
cooling. This setting clears the front view
more quickly.
If you push the windshield air flow button
once again while in the FRONT WIND-
SHIELD mode, the mode then returns to
the last mode used.
CAUTION
To prevent the windshield from fog-
ging up, do not use the windshield air
flow button during cool air operation
in extremely humid weather. The dif-
ference between the temperature of
the outside air and that of the wind-
shield can cause the outer surface of
the windshield to fog up, blocking
your vision.
(d) Micro dust and pollen filter
Push the micro dust and pollen filter
button
Outside air mode switches to recirculated
air mode. Pollen is removed from air and
the air flows to the upper part of the body.
Usually the system will turn off automati-
cally approximately 3 minutes later.
To stop the operation, press the button
again.

REAR VIEW MONITOR SYSTEM
262
The rear view monitor system assists
the driver by displaying an image of the
view behind the vehicle while backing
up. The left and right displayed on the
screen are the same as those of the in-
side rear view mirror.
To display the rear view image on the
screen, place the shift lever in the “R”
position when the “ENGINE START
STOP” switch is in IGNITION ON mode.
If you move the shift lever out of the “R”
position, the screen returns to the previous
screen. Operating another function of the
navigation system will display another
screen.
Vehicles with Intuitive parking assist —
when the Intuitive parking assist are
turned on and an obstacle is detected in
front of or behind your vehicle, a warning
appears on the rear view monitor. For
details, refer to the “Owner’s Manual”.
The rear view monitor system is a supple-
ment device intended to assist back up.
When backing up, be sure to check behind
and all around the vehicle visually.
CAUTION
Never depend on the rear view
monitor system entirely when
backing up. Always make sure
your intended path is clear.
Use caution, just as you would
when backing up any vehicle.
Never back up while looking only at
the screen. The image on the
screen is different from actual
conditions. Depicted distances
between objects and flat surfaces
will differ from actual distance. If
you back up while looking only at
the screen, you may hit a vehicle, a
person or an object. When backing
up, be sure to check behind and all
around the vehicle visually and
with mirrors before proceeding.
Do not use the system when the
back door is not completely
closed.
Use your own eyes to confirm the
vehicle’s surroundings, as the dis-
played image may become faint or
dark, and moving images will be
distorted, or not entirely visible
when the outside temperature is
low. When backing up, be sure to
check behind and all around the ve-
hicle visually and with mirror be-
fore proceeding.
Do not use the system in the follow-
ing cases:
On icy or slick road surfaces, or
in snow.
When using tire chains or emer-
gency tires.
On an uneven road, such as a
slope.
Rear view monitor system —