remote control TOYOTA MR2 SPYDER 2001 Accessories, Audio & Navigation (in English)

ALARM INFORMATION
PANIC MODE OPERATION
When you are confronted by a threatening situation, you may call attenti\
on to your vehicle by
pressing the PANIC button on the back of the remote control. Unless you \
D
ISARMthe PANICALARM
by one of the described methods, it will continue for 60 seconds, then s\
top.To activate the P
ANICALARM:
Press the PANIC button on the back of the remote control. Simultaneously\
: The horn sounds repeatedly for 60 seconds.

The headlights flash repeatedly for 60 seconds.
The tail and marker lights flash repeatedly for 60 seconds.
The interior lights turn on for 60 seconds.
To disarm the Panic Alarm:
Do one of the following shown below.
You may activate a P
ANICALARMat any time, except when the key is in the ignition switch and
turned to the “ON” position. If the system detects an A
LARMTRIGGERduring the PANICALARM, the
regular A
LARMtakes over. See ALARM INFORMATION on pages 12 and 13 for additional
information.

TOYOTARS3200 remote keyless Security system Page 11
PRESS THE
LOCK BUTTON ON THE
REMOTE
CONTROL
,OR...
PRESS THE
PANIC BUTTON AGAIN
,OR...
PRESS THE UNLOCK
BUTTON ON
THE REMOTE CONTROL
,OR...
LOCK THE DOORS
WITH THE KEY,OR...UNLOCK A DOOR OR THE TRUNK WITH THE KEY

THE HORN SOUNDSFOR60SECONDS

HEADLIGHTS FLASHFOR60SECONDS
MARKER LIGHTS FLASH
FOR
60SECONDS
TAIL LIGHTS FLASH FOR60SECONDS
INTERIOR LIGHTS TURN ON FOR60SECONDS

TOYOTARS3200 remote keyless Security systemPage 13
ALARM INFORMATION
ALARM DESCRIPTIONS
RegularALARM
When an ALARMis triggered in any way other than initial detection by the GLASSBREAKAGESENSOR,
the following occur: The horn sounds repeatedly for 60 seconds.
The headlights flash repeatedly for 60 seconds.
The tail and marker lights flash repeatedly for 60 seconds.
The interior lights turn on for 60 seconds.
The starter is disabled (no engine start) until the system is D
ISARMED.
The door lock will be relocked if someone reaches in and unlocks the ins\
ide lock button.
After 60 seconds of A
LARM, the system will REARMand continue to protect the vehicle.
W
ARN-AWAY ALARM
Upon initial detection of noise from tapping on, or breaking glass, the \
GLASSBREAKAGESENSOR
TRIGGERSa WARNAWAYALARM:
The horn sounds repeatedly for 20 seconds.
The headlights flash repeatedly for 20 seconds.
The tail and marker lights flash repeatedly for 20 seconds.
The interior lights turn on for 20 seconds.
If the G
LASSBREAKAGESENSORdetects noise again, or if a door or trunk or hatch is opened while the
system is still A
RMED, the regular ALARM(described above) is activated.
STOPPING AN ALARM
Simply DISARMthe system using the remote control or key as described on page 7.

THE HORN SOUNDS
FOR20SECONDS

HEADLIGHTS FLASHFOR20SECONDS
MARKER LIGHTS FLASH
FOR
20SECONDS
TAIL LIGHTS FLASH FOR20SECONDS

THE HORN SOUNDS FOR60SECONDS
HEADLIGHTS FLASHFOR60SECONDS
THE STARTER IS DISABLED UNTIL THE SYSTEM IS DISARMED
MARKER LIGHTS FLASH
FOR
60SECONDS TAIL LIGHTS FLASH
FOR
60SECONDS
INTERIOR LIGHTS TURN ON FOR60SECONDS
INTERIOR LIGHTS TURN ON FOR20SECONDS


Page 14 TOYOTARS3200 REMOTE KEYLESS Security system
GLASS BREAKAGE SENSOR INFORMATION
The RS3200 provides protection for your vehicle above and beyond entry p\
oint monitoring–it
“listens” for the noise made by tapping on, or breaking of glass. \
Using a microphone designed
specifically for this task, the G
LASSBREAKAGESENSORis capable of ignoring other noises, which
helps to prevent “false alarms” from occurring.
GLASS BREAKAGE SENSOR CHECK PROCEDURE
When the RS3200 was installed in your vehicle, care was taken to adjust \
the sensitivity level of the
G
LASSBREAKAGESENSOR. You may observe how it works following the procedure listed below.
1. A
RMthe system.
Press the LOCK button on the remote control or lock the doors with
the key.
(Remember, the system will not A
RMif any door, the trunk or hatch is
open.)
2. Wait until the S
TATUSMONITOR’SLED starts flashing.
The LED will flash 30 seconds after the last door, the trunk or hatch
is closed.
3. With the tip of a key, tap the center of the driver’s door window. Tap the glass with light to moderate force.
WARNING: Do not hit the glass with excessive force, especially in cold weather, or you may crack or break it.
A W
ARNAWAYALARMshould be TRIGGERED. If the ALARMis not
T
RIGGERED, make sure you performed the procedure correctly and try
again. If you find that the system did not perform as expected,
contact your Toyota dealer for more information.
4. D
ISARMthe system to stop the WARNAWAYALARM.
Press the UNLOCK button on the remote control or use the key to
D
ISARMthe system.

TOYOTARS3200 remote keyless Security systemPage 15
PROGRAMMING
PASSIVE ARMING ON/OFF SELECTION, ENTRY DELAY TIME SELECTION
The RS3200 is factory-set to notPASSIVELYARM. To change the system’s operation for PASSIVE
ARMINGoperation, as well as adjust the ENTRYDELAYtime, follow the procedure below. For more
information on this feature, please refer to page 8.
1. Before you begin: Close all the doors, and the trunk or hatch.
Unlock all the doors with the inside lock switch.
Remove the key from the ignition switch.
2. Start the Programming Procedure. (Complete these steps within 30 seconds.)
3. Select the Operating Mode and Complete the Programming Procedure.

a. Using the remote control,
lock, thenunlock the
doors 3 times . b. Open
the driver’s door.
b. Lock thenunlock the
driver’s door inside lock
button 1 time.

a. Close , then Open the door:
2 times = P
ASSIVEARMINGOFF
3 times = P
ASSIVEARMINGON ,
0 Sec. E
NTRYDELAY
4 times = PASSIVEARMINGON ,
15 Sec. E
NTRYDELAY
5 times = PASSIVEARMINGON ,
30 Sec. E
NTRYDELAY
c. Lock, thenunlock the
driver’s door inside lock
button 3 times .

d.The system locks the door
in 2 seconds; if this does
not happen, start over.
c.The system locks the door
in 2 seconds; if this does
not happen, start over.
Programming is now
complete.
e. Unlock
the driver’s door
inside lock button.

PROGRAMMING
DRIVER’S DOOR/ALL DOORS UNLOCK SELECTION
The RS3200 is factory-set to unlock the driver’s door when the UNLOCK button is pressed on the remote
control, then unlock the remaining doors when the UNLOCK button is press\
ed again within 3 seconds. You
may change the programming so all doors will unlock at once when the UNL\
OCK button is pressed by fol-
lowing the steps below.
1. Before you begin: 2. Start the Programming Procedure.Open the driver’s door. (Complete these steps within 40 seconds.)
Remove the key from the ignition switch.
Note: If the system does not activate the lights and buzzer, start over.
Page 16 TOYOTARS3200 REMOTE KEYLESS Security system
a. Insert the key into, and remove it
from the ignition
switch 2 times.
e. Insert the key into
the ignition and leave it in.c. Insert the key into, and remove it
from the ignition
switch 1 time.
g. Turn the key from LOCK to ON 4
times (ending at
LOCK.) h. Remove the key
from the ignition
switch.
b. Close, then openthe driver’s door
2 times.
f. Close the driver’s door.d. Close, then openthe driver’s door
2 times.
i. The tail and marker lights flash 4 times, the buzzer chirps 4 times, and the doors lock and
unlock 4 times.

PROGRAMMING
IGNITION-CONTROLLED AUTOMATIC DOOR LOCK/UNLOCK
The RS3200 is factory-set to automatically lock your vehicle’s doors \
when you turn the ignition key
to “ON” or “START”, and unlock the doors when you turn the k\
ey back to “ACC” or “LOCK”. To
change the programming of this feature, follow the procedure shown below\
.
1. Before you begin:Open the driver’s door.
Remove the key from the ignition switch.
2. Start the Programming Procedure. (Complete these steps within 30 seconds.)
Note: If the system does not activate the lights and buzzer, start over.\
3. Select the Operating Mode and Complete the Programming Procedure.
Page 18 TOYOTARS3200 REMOTE KEYLESS Security system

a. Insert the key into the
ignition switch and turn it
from LOCK to ON 5 times
(ending at ON). c.
The STATUSMONITOR’SLED
(or the engine immobilizer
system’s LED) turns on
for 30 seconds.
b. Turn the ignition
key backto lock.

a. Close the door =
IG. Controlled Door Locks ON
Close , then open and close
the door again= IG. Controlled
Door Locks OFF c.
The tail and marker lights
flash once and the buzzer
chirps once when the system is
set for IG door lock control ON ,
twice for IG door lock control
OFF . If this does not happen,
start over. Programming is now
complete.
b.
The tail and marker lights
flash once, and the buzzer
chirps once.

TOYOTARS3200 remote keyless Security systemPage 19
REMOTE CONTROL BATTERY REPLACEMENT
The following shows the procedure to replace the batteries in your remot\
e controls. We recom-
mend that you replace the batteries at least once a year, or when the re\
mote control’s transmitting
range diminishes. You may obtain the replacement battery from your Toyot\
a dealer, as well as
many retailers that sell watch batteries. The battery replacement type is a Lithium CR2025.
Important notes on battery replacement:
When replacing the battery, be careful not to lose the components.
Take care not to bend or damage the rubber gasket.
REMOVE THE BATTERY
1. Lay the remote control on a towel or other soft material. Place it with the back side facing up.
2. Using a coin, pry open the remote control. Use gentle pressure to avoid deforming the plastic.
3. Set the back cover aside.
4. Remove the rubber gasket and set it aside.
5. Push the battery down and toward you, and hold it down.
6. Pry the back edge of the battery up and toward you.

Page 20 TOYOTARS3200 REMOTE KEYLESS Security system
REMOTE CONTROL BATTERY REPLACEMENT
INSTALL THE BATTERY
1. Hold the battery with the plus side up.Handle the battery with a cloth or tissue; body oils and moisture can
interfere with operation and may reduce the life of the battery.
2. Insert the new battery as shown. Place the edge of the battery in the contacts first, then slide the
battery back and down.
3. Place the rubber gasket back on the remote control. Make sure the gasket is seated properly.
4. Place the back cover back on the top half of the remote control. Place even pressure and listen for the halves to “snap” together.

TOYOTARS3200 remote keyless Security systemPage 21
Warning
•This product is applicable only to vehicles with 12V DC, negative ground\
ing specifications. Do
not use in vehicles with 24V specifications . Otherwise, damage to the unit or a fire may result.
•To prevent accidents from occurring, keep the remote controls’ batter\
ies out of the reach of
children. In the event a battery is swallowed, consult a physician immed\
iately.
•Never attempt to disassemble or modify the product. Otherwise, an accide\
nt, fire or electric
shock may result.
•When replacing fuses, be sure to use fuses with the same specified capac\
ity (amperage.)
Otherwise, damage to the unit or vehicle, fire or electric shock may res\
ult.
•If an abnormal condition occurs, such as liquids spilling onto the produ\
ct, or the product
emitting smoke or strange odors, stop using it immediately and consult t\
he dealer from whom
you purchased the product. Continued use of the product before correctiv\
e actions are taken
may result in an accident, injury or fire.
•Never pull the plastic bag over your head. Otherwise, a serious injury o\
r death from suffocation
may occur.
Caution
•Do not use batteries other than the type specified.
•When placing batteries into the product, insert them as shown, paying cl\
ose attention to the
polarities (+ and -). If inserted improperly, the battery may explode,\
or leak electrolyte and
contaminate the surrounding area.
•Do not use this product for applications other than in-vehicle use. Othe\
rwise, an electric shock
or injury may result.
•Do not allow children to play with the remote controls. Otherwise, the d\
oors may be locked or
unlocked, the security system armed or disarmed, or an alarm triggered u\
nintentionally.
•If this product is dropped or its case is damaged, disconnect the power \
supply lead and
contact the dealer from whom you purchased it to obtain service. Otherwi\
se, a fire or electric
shock may result.