display TOYOTA RAV4 HYBRID 2021 (in English) Owner's Manual

46
TOYOTA SAFETY SENSE™
LANE CENTERING
The lane centering function is linked with Full-Speed Range Dynamic Radar Cruise
$POUSPM %3$$
BOEQSPWJEFTUIFSFRVJSFEBTTJTUBODFCZPQFSBUJOHUIFTUFFSJOH
wheel to keep the vehicle in its current lane.
When dynamic radar cruise control with full-speed range is not operating, the lane
centering function does not operate.

1SFTT“
” switches and select “”GSPNUIF.VMUJ*OGPSNBUJPO%JTQMBZ .*%


1SFTT“
” switches and select “ LTA” and then press “.” The setting
screen is displayed.

1SFTT“
” switches and select the “Lane Center” setting function and then
press “
” to select the desired setting.

1SFTT“
” to go back to the menu.
Note: Operation of the LTA system and setting adjustments continues in the
same condition regardless of Ignition cycle until changed by the driver or the
system is reset.
Refer to the Toyota Owner’s Manual for additional information on LTA operation,
settings adjustments, limitations, and precautions before attempting to use it.
DISABLING LANE CENTERING FUNCTION

47
OVERVIEW FEATURES & OPERATIONS TOYOTA SAFETY SENSE SAFETY & EMERGENCY FEATURES
TURNING SYSTEM ON/OFF
(1)
Push once: On
Push twice: Off
Full-Speed Range Dynamic Radar Cruise Control
(DRCC)
Intended for highway use, Full-Speed Range Dynamic Radar Cruise Control
%3$$
MFUTZPVESJWFBUBQSFTFUTQFFE5IFTZTUFNJTEFTJHOFEUPGVODUJPO
between 0-110 mph* and uses vehicle-to-vehicle distance control, helping maintain
a preset distance from the vehicle ahead of you.*
* See Toyota.com/safety-sense for more information.
Refer to the Toyota Owner’s Manual for a list of additional situations in which the
system operation may be limited.
Refer to page 49 for switching to Constant Speed (Cruise) Control Mode.
ADJUSTING SET SPEED
(3) (2)
Vehicle will cruise at a set speed, decelerate to maintain selected distance from a
slower vehicle traveling in front and accelerate back up to the selected speed if the
vehicle in front changes lanes or speeds up.


1VTIi
” to turn DRCC system ON. The “RADAR READY” and “”
indicator will come on.

 6TFUIFTUFFSJOHXIFFMDPOUSPMTUPJODSFBTFTQFFECZQVTIJOH“+RES” or
decrease the speed by pushing “-SET.” Push and hold to make a large
BEKVTUNFOUPSQVTIFBDIUJNFUPNBLFGJOFBEKVTUNFOUT NQI<LNI>PS
LNI<NQI>JODSFNFOUT


1VTI“Cancel” to cancel the speed control.
Increase speed/Resume
Cancel*
Decrease speed
* The speed control may also be canceled by depressing the brake pedal.
Multi-information
display
Set speedDynamic Radar Cruise
Control vehicle-to-
vehicle distance
button
Cruise control
switch
Indicators

49
OVERVIEW FEATURES & OPERATIONS TOYOTA SAFETY SENSE SAFETY & EMERGENCY FEATURES
"%+645*/(%*45"/$& $0/5*/6&%

Note: When your vehicle is too close to a vehicle ahead, and sufficient automatic
deceleration via the cruise control is not possible, the display will flash and the
buzzer will sound to alert the driver. An example of this would be if another driver
cuts in front of you while you are following a vehicle. Depress the brake pedal to
ensure an appropriate vehicle-to-vehicle distance.

Acceleration when there are no longer any preceding vehicles driving
slower than the set speed
The system accelerates until the set speed is reached. The system then
returns to constant speed cruising.
48*5$)*/(50$0/45"/541&&% $36*4&
$0/530-.0%&
4&55*/($0/45"/541&&% $36*4&
$0/530-
If you are already using DRCC “,” push ON-OFF button to turn the system off
first, then push and hold ON-OFF button for at least 1.5 seconds to switch.
Note: When the vehicle is turned off, it will automatically default to DRCC.
Refer to the Toyota Owner’s Manual for additional information on DRCC operation,
settings adjustments, limitations, and precautions before attempting to use it.
1.5 seconds
Set
To adjust speed or cancel, see steps (2) and (3) of ADJUSTING SET SPEED on
page 47.

51
OVERVIEW FEATURES & OPERATIONS TOYOTA SAFETY SENSE SAFETY & EMERGENCY FEATURES
Road Sign Assist (RSA)
6TJOHBOJOUFMMJHFOUDBNFSB
3PBE4JHO"TTJTU 34"
JTEFTJHOFEUPEFUFDUTQFFE
limit signs, stop signs, do not enter signs and yield signs, and display them on the
.VMUJ*OGPSNBUJPO%JTQMBZ .*%

* All vehicle actions must be driver-initiated and are not automated. See Toyota.
com/safety-sense for model applicability.
Refer to the Toyota Owner’s Manual for a list of additional situations in which the
system operation may be limited.
SETTING RSA

1SFTT“ ” switches and select “”GSPNUIF.VMUJ*OGPSNBUJPO%JTQMBZ .*%


1SFTT“
” switches and select “ RSA” and then press “.”

1SFTT“
” switches and select the “Road Sign Assist on/off” setting function
and then press “
” to select the desired setting.

1SFTT“
” to go back to the menu.
Note: If the vehicle was last turned off while a speed limit sign was displayed
on the multi-information display, the same sign displays again when the
vehicle is turned back on.
Refer to the Toyota Owner’s Manual for additional information on RSA operation,
settings adjustments, limitations, and precautions before attempting to use it.
RSA DISPLAY
SUPPORTED TYPES OF ROAD SIGNS
When the driving support system
information is selected, a maximum of
3 signs can be displayed.
Speed limit Stop
Do Not Enter YieldWhen a tab other than the driving
support system information display is
selected, the following types of road
signs will be displayed.
• Speed limit sign
t%P/PU&OUFSTJHO XIFOOPUJGJDBUJPO
JTOFDFTTBSZ

54
SAFETY & EMERGENCY FEATURES
Tire Pressure Monitoring (warning) System (TPMS)
The tire pressure warning system can be selected on “” of the Multi-Information
%JTQMBZ .*%

System reset initialization

Press “
” switches and select “”GSPNUIF.VMUJ*OGPSNBUJPO%JTQMBZ .*%


Press “
” switches and select the “ 7FIJDMF4FUUJOHT

wUIFOQVTIi.”

Press “
” switches and select “TPWS” and then push “.”

Press “
” switches and select “Set Pressure” then push and hold “” until
the warning light blinks three times.
The tire pressure detected by the tire pressure warning system can be displayed
POUIFNVMUJJOGPSNBUJPOEJTQMBZ .*%

Refer to the load label on the door jamb or the Owner’s Manual for tire inflation
specifications.
If the tire pressure indicator flashes for 1 minute and then remains on, take the
vehicle to your local Toyota dealer.
NOTE: The warning light may come on due to temperature changes or
changes in tire pressure from natural air leakage. If the system has not been
initialized recently, setting the tire pressures to factory specifications should
turn off the light.

59
To begin the Bluetooth® Pairing process, press the HOME button on the faceplate of
your multimedia system.
Bluetooth® Pairing for your phone
Pairing your phone is the first step in connecting with your Toyota. This pairing
process is quick and easy. All you have to do is setup the phone and multimedia
system to form a connection.
1

Select &#34;Bluetooth,&#34; then select
&#34;Add New Device&#34; on display
screen. Ensure Bluetooth is turned on for
your device.
Select &#34;Device Name.&#34;
iPhone bluetooth MenuAndroid bluetooth Menu
1
Some Android devices may have slightly different SETTINGS screen layout depending on manufacturer of device and Android OS version.
Check the display on your smart
phone. Does the PIN XXXX
match the PIN displayed? If it
does, select &#34;Pair.&#34;
1SFTT<.&/6>POUIFBVEJPTZTUFNGBDFQMBUF
UIFOTFMFDU

60
BLUETOOTH® DEVICE PAIRING
&#34;Connecting&#34; displays while
device is forming the connection
to your multimedia system.&OBCMF/PUJGJDBUJPOT UFYU
NFTTBHF
8IJMFQBJSJOHZPVS
phone, a message will be
displayed:
&#34;You may need to allow
message access on your
phone.&#34;
Note: You may also select
&#34;Skip&#34; on display screen to skip
enabling notifications. If skipped,
proceed to
Step 8.
Turn on &#34;Show Notifications&#34; for
iPhone or &#34;ON&#34; for Android.A confirmation will appear once
your phone has been paired and
connected.
iPhoneAndroid
Bluetooth® Pairing for your phone (cont.)
STEP 6
STEP 8
STEP 7
STEP 9