key TOYOTA RAV4 PLUG-IN HYBRID 2022 User Guide

81
1
1-4. Theft deterrent system
For safety and security
OIce or snow is removed from the vehi-
cle, causing the vehicle to receive repeated impacts or vibrations.
OThe vehicle is inside an automatic or high-pressure car wash.
OThe vehicle experiences impacts, such as hail, lightning strikes, and other kinds of repeated impacts or
vibrations.
QTilt sensor detection consider- ations
The sensor may trigger the alarm in the
following situations:
OThe vehicle is transported by a ferry,
trailer, train, etc.
OThe vehicle is parked in a parking
garage.
OThe vehicle is inside a car wash that
moves the vehicle.
OAny of the tires loses air pressure.
OThe vehicle is jacked up.
OAn earthquake occurs or the road caves in.
NOTICE
QTo ensure the intrusion sensor functions correctly
OTo ensure that the sensors operate properly, do not touch or cover them.
ODo not spray air fresheners or other products directly into the sensor
holes.
OInstalling accessories other than
genuine Toyota parts or leaving objects between the driver’s seat and front passenger’s seat may
reduce the detection performance.
OThe intrusion sensor may be can-
celed when the electronic key is near the vehicle.

115
2
2-2. Charging
Plug-in hybrid system
1 Prepare the AC charging cable
( P.109) and the replacement
plug-cord.
2 Pull out the release key.
Make sure that the pulled out release key is not lost.
3 Remove the plug-cord connec-
tor cap.
4 Insert the release key into the
release slot of the CCID
(Charging Circuit Interrupting
Device).
Insert the release key in the direction
shown in the illustration.
5 With the release key fully
inserted into the release slot of
the CCID (Charging Circuit
Interrupting Device), turn the
plug-cord connector nut of the
plug-cord to remove the cord.
After the plug-cord is removed, remove the release key.
Do not leave the vehicle alone with the plug-cord removed. If the plug-cord is not installed, water or other foreign
matter may enter the CCID (Charging Circuit Interrupting Device), resulting in a malfunction.
6 Align the protrusion of the CCID
(Charging Circuit Interrupting
Device), with the groove of the
plug-cord, insert the plug-cord
into the CCID (Charging Circuit
Interrupting Device), and then
turn the plug-cord connector nut
of the plug-cord to install it.

1162-2. Charging
Make sure that there are no foreign
objects attached to the connection before installing the plug-cord. Remove any foreign objects if they are attached.
Otherwise, water or other foreign mat- ter may enter the CCID (Charging Cir-cuit Interrupting Device), resulting in a
malfunction.
Turn the plug-cord connector nut of the plug-cord in the opposite direction of
removal until a click sound is heard and the plug-cord is secured.
7 Install the plug-cord connector
cap and release key to the plug-
cord that has been removed.
Securely install the release key to the plug-cord connector cap to prevent it
from being lost. Also, make sure that the release key does not fall out of the plug-cord connector cap accidentally.
Store the plug-cord in a safe, clean and dry place.
For safety, inspect the AC charging
cable on a routine basis.
WARNING
QWhen replacing the plug-cord (if
equipped)
Check the following points regularly.
Failure to do so may cause an unex-
pected accident, resulting in death or serious injury.
ODo not replace the plug-cord with wet hands.Also, do not replace in a place that
is rainy or wet.
ODo not replace the plug-cord when
the plug and/or charging connector are connected.
OCheck whether there are any local EV-charging regulations in place, and adhere to them.
ODo not leave the CCID (Charging Circuit Interrupting Device) with the
plug-cord removed.
OMake sure that there are no foreign
objects attached to the connection when installing the plug-cord to the CCID (Charging Circuit Interrupting
Device).
OWhen replacing the plug-cord,
firmly turn the nut of the plug-cord until a click sound can be heard.
ODo not replace the plug cord in Nor-way.
NOTICE
QPrecautions for the plug-cord (if
equipped)
Do not use the plug-cord for any use other than charging this vehicle.
Doing so may cause the plug-cord to be damaged.
Inspecting and maintaining
the AC charging cable

1202-2. Charging
QUnlocking the charging port
lid
1Unlock the doors using the
smart entry & start system or
wireless remote control.
2Press the central rear edge of
the charging port lid (the loca-
tion shown in the illustration)
and open it.
QLocking the charging port lid
The charging port lid will be locked
when the lid is closed and the doors
are locked using the smart entry &
start system or wireless remote
control.
QSecurity feature
If the doors are locked by the security
function when the charing port lid is
closed, the charging port lid will also be
locked. (P.204)
QLocking the charging port lid
If the charging port lid is closed after the
doors are locked, the lid will not be
locked. In this case, close the lid and
then lock the doors again.
QIf the charging port lid does not
open
If the charging port lid does not open
when using the normal procedure, it can
be opened in an emergency by perform-
ing the following steps.
1Open the back door. (P.210, 211)
2Pull the 12-volt battery cover and
remove it. (P.462)
3Hook a finger to the emergency
release lever as shown in the illus-
tration.
4Move the emergency release lever
in the direction shown in the illustra-
tion.
*
The charging port lid is unlocked and
can be opened.
*: Make sure to move in the direction
shown in the illustration. Applying
force in other directions may damage
Locking and unlocking
the charging port lid and
charging connector
The charging port lid and
charging connector can be
locked/unlocked by the follow-
ing procedures.
Using the smart entry & start
system
*: P.203
Using the wireless remote con-
trol
*: P.201
*: If the smart entry & start system or
the wireless remote control does
not operate properly, use the
mechanical key. (P.545)
Locking and unlocking the
charging port lid

4
199
4
Before driving
Before driving
4-1. Key information
Keys.................................. 200
4-2. Opening, closing and locking
the doors
Side doors ........................ 203
Back door ......................... 208
Smart entry & start system 221
4-3. Adjusting the seats
Front seats........................ 226
Rear seats ........................ 227
Driving position memory ... 229
Head restraints ................. 232
4-4. Adjusting the steering wheel
and mirrors
Steering wheel .................. 234
Inside rear view mirror ...... 235
Digital Rear-view Mirror .... 236
Outside rear view mirrors . 245
4-5. Opening, closing the win-
dows and moon roof
Power windows................. 247
Panoramic moon roof ....... 250

2004-1. Key information
4-1.Key info rmation
The following keys are provided
with the vehicle.
Electronic keys
• Operating the smart entry & start sys-
tem ( P.221)
• Operating the wireless remote control
function ( P.201)
• Operating the Remote Air Condition-
ing System ( P.414)
Mechanical keys
Key number plate
QWhen riding in an aircraft
When bringing an electronic key onto an aircraft, make sure you do not press any
buttons on the electronic key while inside the aircraft cabin. If you are carry-ing an electronic key in your bag etc.,
ensure that the buttons are not likely to be pressed accidentally. Pressing a but-ton may cause the electronic key to emit
radio waves that could interfere with the operation of the aircraft.
QElectronic key battery depletion
OThe standard battery life is 1 to 2 years.
OIf the battery becomes low, an alarm will sound in the cabin and a message will be displayed on the multi-informa-
tion display when the hybrid system
stops.
OTo reduce key battery depletion when
the electronic key is to not be used for long periods of time, set the electronic key to the battery-saving mode.
( P.222)
OAs the electronic key always receives
radio waves, the battery will become depleted even if the electronic key is not used. The following symptoms
indicate that the electronic key battery may be depleted. Replace the battery when necessary.
• The smart entry & start system or the wireless remote control does not oper-ate.
• The detection area becomes smaller. • The LED indicator on the key surface does not turn on.
You can replace the battery by yourself
( P.486). However, as there is a dan-
ger that the electronic key may be dam-
aged, it is recommended that
replacement is carried out by any autho-
rized Toyota retailer or Toyota autho-
rized repairer, or any reliable repairer.
OTo avoid serious deterioration, do not leave the electronic key within 1 m (3
ft.) of the following electrical appli- ances that produce a magnetic field:•TVs
• Personal computers • Cellular phones, cordless phones and battery chargers
•Table lamps • Induction cookers
OIf the electronic key is near the vehicle for longer than necessary, even if the smart entry & start system is not oper-
ated, the key battery may become depleted faster than normal.
QIf a message regarding the state of the electronic key or power switch
mode, etc. is shown
To prevent trapping the electronic key inside the vehicle, leaving the vehicle
carrying the electronic key on your per- son without turning the power switch to
Keys
Key types
A
B
C

201
4
4-1. Key information
Before driving
OFF or other passengers from uninten-
tionally taking the key out of the vehicle, etc., a message that prompts the user to confirm the state of the electronic key or
power switch mode may be shown on the multi-information display. In those cases, follow the instructions on the dis-
play immediately.
QIf “Key Battery Low Replace Key Battery” is displayed on the multi-information display
The electronic key has a low battery. Replace the electronic key battery. ( P.486)
QReplacing the battery
 P.486
QConfirmation of the registered key number
The number of keys already registered
to the vehicle can be confirmed. Ask any authorized Toyota retailer or Toyota authorized repairer, or any reliable
repairer for details.
QIf “A New Key has been Registered Contact Your Dealer for Details” is displayed on the multi-information
display
This message will be displayed each time the driver’s door is opened when
the doors are unlocked from the outside for approximately 10 days after a new electronic key has been registered.
If this message is displayed but you have not had a new electronic key regis-tered, ask any authorized Toyota retailer
or Toyota authorized repairer, or any reliable repairer to check if an unknown electronic key (other than those in your
possession) has been registered.
The electronic keys are equipped
with the following wireless remote
control:
NOTICE
QTo prevent key damage
ODo not drop the keys, subject them
to strong shocks or bend them.
ODo not expose the keys to high
temperatures for long periods of time.
ODo not get the keys wet or wash them in an ultrasonic washer, etc.
ODo not attach metallic or magnetic materials to the keys or place the keys close to such materials.
ODo not disassemble the keys.
ODo not attach a sticker or anything else to the surface of the electronic key.
ODo not place the keys near objects that produce magnetic fields, such
as TVs, audio systems and induc- tion cookers.
ODo not place the keys near medical electrical equipment such as low-frequency therapy equipment or
microwave therapy equipment, and do not receive medical attention with the keys on your person.
QCarrying the electronic key on your person
Carry the electronic key 10 cm (3.9 in.) or more away from electric appli-ances that are turned on. Radio
waves emitted from electric appli- ances within 10 cm (3.9 in.) of the electronic key may interfere with the
key, causing the key to not function properly.
QIn case of a smart entry & start system malfunction or other key-related problems
 P.544
QWhen an electronic key is lost
 P.543
Wireless remote control

2024-1. Key information
Locks all the doors (P.203)
Closes the side windows*1 and
the panoramic moon roof*1, 2
( P.203)
Unlocks all the doors ( P.203)
Opens the side windows*1 and
the panoramic moon roof*1, 2
( P.203)
Opens and closes the power
back door*2 ( P.211)
Operates Remote Air Condition-
ing System ( P.414)
*1: These settings must be customized
at any authorized Toyota retailer or
Toyota authorized repairer, or any
reliable repairer.
*2: If equipped
To take out the mechanical key,
slide the release lever and take
the key out.
The mechanical key can only be
inserted in one direction, as the key
only has grooves on one side. If the key
cannot be inserted in a lock cylinder,
turn it over and re-attempt to insert it.
After using the mechanical key, store it
in the electronic key. Carry the
mechanical key together with the elec-
tronic key. If the electronic key battery
is depleted or the entry function does
not operate properly, you will need the
mechanical key. ( P.544)
QWhen required to leave the vehi-
cle’s key with a parking attendant
Lock the glove box as circumstances demand. ( P.423)
Remove the mechanical key for your own use and provide the attendant with the electronic key only.
QIf you lose your mechanical keys
 P.543
QIf a wrong key is used
The key cylinder rotates freely to isolate inside mechanism.
Using the mechanical key
A
B
C
D
E
F
A

203
4
4-2. Opening, closing and locking the doors
Before driving
4-2.Opening, closing and lo cking th e d oors
QUsing the entry function
Carry the electronic key to enable
this function.
1 Grip the front door handle to
unlock the doors.
Make sure to touch the sensor on the
back of the handle.
The doors cannot be unlocked for 3
seconds after the doors are locked.
2 Touch the lock sensor (the
indentation on the upper part of
the door handle) to lock the
doors.
Check that the door is securely locked.
QUsing the wireless remote
control
1 Locks all the doors
Check that the door is securely locked.
Press and hold to close the side win-
dows and panoramic moon roof (if
equipped).*
2 Unlocks all the doors
Press and hold to open the side win-
dows and panoramic moon roof (if
equipped).*
*: These settings must be customized
at any authorized Toyota retailer or
Toyota authorized repairer, or any
reliable repairer.
QSwitching the door unlock function
It is possible to set which doors the entry function unlocks using the wireless
remote control. Operate the switching operation in the vehicle or within approx-imately 1 m (3.2 ft.) of the vehicle.
1 Turn the power switch to OFF.
2 Cancel the intrusion sensor and tilt
sensor of the alarm system to pre- vent unintended triggering of the
alarm while changing the settings. (if equipped) ( P.79)
3 When the indicator light on the key surface is not on, press and hold
or for approximately
5 seconds while pressing and hold-
ing .
Side doors
The vehicle can be locked and
unlocked using the entry func-
tion, wireless remote control,
door lock switches or inside
lock buttons.
Charging port lid and charging
connector will also be locked and
unlocked. ( P.120)
Unlocking and locking the
doors from the outside

2044-2. Opening, closing and locking the doors
The setting changes each time an oper-
ation is performed, as shown below.
(When changing the setting continu-
ously, release the buttons, wait for at
least 5 seconds, and repeat step 3.)
Vehicles with alarm: To prevent unin-
tended triggering of the alarm, unlock
the doors using the wireless remote
control and open and close a door once
after the settings have been changed. (If
a door is not opened within 30 seconds
after is pressed, the doors will
be locked again and the alarm will auto-
matically be set.)
In a case that the alarm is triggered,
immediately stop the alarm. (P.78)
QImpact detection door lock release
system
In the event that the vehicle is subject to
a strong impact, all the doors are
unlocked. Depending on the force of the
impact or the type of accident, however,
the system may not operate.
QOperation signals
Doors: The emergency flashers flash to
indicate that the doors have been
locked/unlocked. (Locked: Once;
Unlocked: Twice)
Side windows and panoramic moon roof
(if equipped): A buzzer sounds to indi-
cate that the side windows and pan-
oramic moon roof are operating.
QSecurity feature
If a door is not opened within approxi-
mately 30 seconds after the vehicle is
unlocked, the security feature automati-
cally locks the vehicle again. (However,
depending on the location of the elec-
tronic key, the key may be detected as
being in the vehicle. In this case, vehicle
may be unlocked.)
QWhen the door cannot be locked by
the lock sensor on the upper part of
the door handle
If the door will not lock even when the
topside sensor area is touched, try
touching both the topside and underside
sensor areas at the same time.
When gloves are being worn, remove
the gloves.
QDoor lock buzzer
A buzzer sounds continuously for 5 sec-
onds in the following situations. Fully
close all the doors and lock the vehicle
once more.
OIf an attempt to lock the doors using
the smart entry & start system is made
when a door other than the door you
are locking is open.
OIf an attempt to lock the doors using
the wireless remote control is made
when a door is open.
Multi-information
display/BeepUnlocking function
(Left-hand drive
vehicles)
(Right-hand drive
vehicles)
Exterior: Beeps 3
times
Holding the driver’s
door handle
unlocks only the
driver’s door.
Holding the front
passenger’s door
handle or pressing
the back door
opener switch
unlocks all the
doors.
Exterior: Beeps
twice
Holding either front
door handle or
pressing the back
door opener switch
unlocks all the
doors.