TOYOTA SUPRA 1995 Service Repair Manual

2. ADJUST FRONT DOOR GLASS
Upper side of glass±in/out
(a) Remove the lower plate bolt.
(b) Pull the lower plate so that the snap is unlocked.
(c) Remove the snap and lower plate.
(d) Adjust the glass by turning the setting nut.
(e) Reinstall the lower plate, snap and bolt.
Position (forward/rearward) and attitude of glass
Loosen 3 bolts of the carrier plate and adjust.
Position (vertical) and attitude of glass
(when glass fully closed)
Adjust the door window upper stop. BO±16
± BODYFRONT DOOR

BACK DOOR
BACK DOOR ADJUSTMENT
1. ADJUST DOOR IN HORIZONTAL DIRECTION
(a) Remove the back door trim board.
(b) Remove the roof headlining. (See pages BO±58 to 61)
(c) Adjust the door by loosening the body side hinge nuts.
Torque: 21 NVm (210 kgfVcm, 15 ftVlbf)
HINT: Since the centering nut is used as the back door hinge
nut, the back door cannot be adjusted with it on. Substitute
the standard nut for the centering nut.
(d) Reinstall the removed parts in the reverse order to their
removal.
2. ADJUST DOOR IN VERTICAL DIRECTION
Adjust the door by loosening the back door side hinge bolts.
Torque: 13 NVm (130 kgfVcm, 9.4 ftVlbf)
HINT: Substitute the standard bolt for the centering bolt. (See
page BO±10)
3. ADJUST DOOR LOCK
(a) Remove the clips and the deck trim rear cover.
(b) Loosen the lock mounting bolts to adjust.
Torque: 19 NVm (195 kgfVcm, 14 ftVlbf)
(c) Using a brass bar and hammer, tap the lock to adjust it.
CAUTION: Do not tap the lock too hard. (See page BO±12)
(d) Install the deck trim rear cover.
BACK DOOR LOCK STRIKER REMOVAL
AND INSTALLATION
1. REMOVE BACK DOOR TRIM BOARD
2. REMOVE AND INSTALL STRIKER
Torque: 13 NVm (130 kgfVcm, 9.4 ftVlbf)
3. INSTALL BACK DOOR TRIM BOARD
± BODYBACK DOORBO±17

BACK DOOR DAMPER STAY REMOVAL
1. REMOVE ROOF SIDE INNER GARNISH
(See page BO±60)
2. REMOVE DAMPER STAY LOWER END FROM BODY
3. REMOVE DAMPER STAY UPPER END FROM BACK
DOOR
NOTICE: When handling the damper.
wDo not disassemble the damper because the cylinder is
filled with pressurized gas.
wIf the damper is to be replaced, drill a 2.0±3.0 mm
(0.079±0.118 in.) hole in the bottom of the removed
damper cylinder to completely release the high±pressure
gas before disposing of it.
wWhen drilling, chips may fly out so work carefully.
wThe gas is colorless, odorless and non±toxic.
wWhen working, handle the damper carefully. Never score
or scratch the exposed part of the piston rod, and never
allow paint or oil to get on it.
wDo not turn the piston rod and cylinder with the damper
fully extended.
BACK DOOR DAMPER STAY
INSTALLATION
1. INSTALL DAMPER STAY UPPER END TO BACK DOOR
NOTICE: Apply adhesive to the bolts before tightening.
Nut to body
Torque: 5.9 NVm (60 kgfVcm, 52 in.Vlbf)
Bolt to back door
Torque: 7.8 NVm (80 kgfVcm, 69 in.Vlbf)
2. INSTALL DAMPER STAY LOWER END TO BODY
3. INSTALL ROOF SIDE INNER GARNISH
(See page BO±60) BO±18
± BODYBACK DOOR

WIPER AND WASHER
COMPONENTS
± BODYWIPER AND WASHERBO±19

COMPONENTS (Cont'd)
BO±20± BODYWIPER AND WASHER

FRONT WIPER REMOVAL
1. REMOVE THESE PARTS:
(a) Wiper arm and blade
(b) Cowl top ventilator louver
2. REMOVE FRONT WIPER MOTOR
(a) Disconnect the connector, then unfasten the 3 bolts.
(b) Remove the wiper motor with the link.
FRONT WIPER INSTALLATION
1. INSTALL THESE PARTS:
(a) Wiper motor with link
(b) Cowl top ventilator louver
2. INSTALL WIPER ARM AND BLADE
(a) Install the wiper arms and operate the wipers once and turn
the wiper switch OFF.
(b) Adjust the installation positions of the wiper arms to the
positions shown in the illustration.
(A) Approx. 32.4 mm (1.28 in.)
(B) Approx. 33.7 mm (1.33 in.)
(c) Torque the nut.
Torque: 22 NVm (225 kgfVcm, 16 ftVlbf)
FRONT WASHER NOZZLE ADJUSTMENT
1. INSPECT FRONT WASHER NOZZLE
(a) While operating the washer, check that both the point where
the washer fluid from the upper nozzles hits the windshield,
and the up surge area, are within the range indicated by the
hatched line.
(A) Approx. 275 mm (10.8 in.)
(B) Approx. 150 mm (5.9 in.)
(C) Approx. 50 mm (2.0 in.)
(D) Within 100 mm (3.9 in.)
(b) Ensure that the lower point where the washer fluid hits the
windshield is within the range of the wiping pattern (the area
of the glass which is wiped by the wiper blades.
2. ADJUST FRONT WASHER NOZZLE
Using a tool like that shown in the illustration, change the
direction of the nozzle hole to adjust the point where washer
fluid strikes the windshield.
± BODYWIPER AND WASHERBO±21

REAR WIPER REMOVAL
1. REMOVE WIPER ARM AND BLADE
2. REMOVE BACK DOOR TRIM BOARD
3. REMOVE WIPER MOTOR ASSEMBLY
(a) Disconnect the connector, then unfasten the 3 bolts.
(b) Remove the motor.
REAR WIPER INSTALLATION
1. INSTALL THESE PARTS:
(a) Wiper motor
(b) Back door trim board
2. INSTALL WIPER ARM AND BLADE
(a) Install the wiper arm and operate the wiper once and turn the
wiper switch OFF.
(b) Adjust the top of the wiper blade to the installation mark
printed on the glass.
(c) Torque the nut.
Torque: 11 NVm (110 kgfVcm, 8.0 ftVlbf)
REAR WASHER NOZZLE ADJUSTMENT
1. INSPECT REAR WASHER NOZZLE
While operating the washer, check that the point where the
washer fluid hits the back door glass is within the range indi-
cated by the hatched line.
(A) Approx. 300 mm (11.8 in.)
(B) Approx. 150 mm (5.9 in.)
2. ADJUST REAR WASHER NOZZLE
(See step 2 on page BO±21) BO±22
± BODYWIPER AND WASHER

WINDSHIELD MOULDING
COMPONENTS
± BODYWINDSHIELD MOULDINGBO±23

WINDSHIELD MOULDING REMOVAL
1. REMOVE THESE PARTS:
(a) Wiper arm and blade
(b) Cowl top ventilator louver
2. REMOVE WINDSHIELD MOULDING
(a) Using a knife, cut off the moulding as shown.
(b) Cut away the adhesive at the moulding installation area as
much as possible.
NOTICE: Do not damage the body with the knife.
WINDSHIELD MOULDING INSTALLATION
1. CUT ADHESIVE AT MOULDING INSTALLATION AREA
Using the knife, cut off the adhesive around the moulding
installation area.
2. APPLY ADHESIVE AT MOULDING INSTALLATION AREA
3. INSTALL WINDSHIELD MOULDING
Place the moulding onto the body and tap it by hand.
4. INSTALL THESE PARTS:
(a) Cowl top ventilator louver
(b) Wiper arm and blade
Torque: 22 NVm (225 kgfVcm, 16 ftVlbf)
BO±24± BODYWINDSHIELD MOULDING

BODY OUTSIDE MOULDING
COMPONENTS
± BODYBODY OUTSIDE MOULDINGBO±25