light TOYOTA T100 1996 Factory Service Manual

Downloaded from www.Manualslib.com manuals search engine P20582
Terminal F
− CHARGING (3RZ−FE)CHARGING SYSTEM
CH−5
1996 TOYOTA T100 (RM449U)
Connect the test lead from the positive (+) terminal
of the ammeter to terminal B of the generator.
Connect the positive (+) lead of the voltmeter to ter-
minal B of the generator.
Ground the negative (−) lead of the voltmeter.
(b) Check the charging circuit as follows:
With the engine running from idling to 2,000 rpm, check
the reading on the ammeter and voltmeter.
Standard amperage:
10 A or less
Standard voltage:
At 25 °C (77°F): 14.0 − 15.0 V
At 115 °C(239 °F): 13.5 − 14.3 V
If the voltage reading is greater than standard voltage, replace
the voltage regulator.
If the voltage reading is less than standard voltage, check the
voltage regulator and generator as follows:
With terminal F grounded, start the engine and
check the voltage reading of terminal B.
If the voltage reading is higher than standard volt-
age, replace the voltage regulator.
If the voltage reading is less than standard voltage,
repair the generator.
10. INSPECT CHARGING CIRCUIT WITH LOAD
(a) With the engine running at 2,000 rpm, turn on the high
beam headlights and place the heater fan control switch
to HI.
(b) Check the reading on the ammeter.
Standard amperage:
30 A or more
If the ammeter reading is less than standard amperage, repair
the generator.
HINT:
If the battery is fully charged, the indication will sometimes be
less than standard amperage.

Downloaded from www.Manualslib.com manuals search engine CH02P−03
S05376
Except Maintenance−Free Battery
Z18827
Voltmeter Maintenance−Free Battery
− CHARGING (5VZ−FE)CHARGING SYSTEM
CH−1
1220 Author: Date:
1996 TOYOTA T100 (RM449U)
CHARGING SYSTEM
ON−VEHICLE INSPECTION
CAUTION:
Check that the battery cables are connected to the
correct terminals.
Disconnect the battery cables when the battery is giv-
en a quick charge.
Do not perform tests with a high voltage insulation re-
sistance tester.
Never disconnect the battery while the engine is run-
ning.
1. CHECK BATTERY ELECTROLYTE LEVEL
Check the electrolyte quantity of each cell.
Maintenance−Free Battery:
If under the lower level, replace the battery (or add distilled wa-
ter if possible) and check the charging system.
Except Maintenance−Free Battery:
If under the lower level, add distilled water.
2. Except Maintenance−Battery:
CHECK BATTERY SPECIFIC GRAVITY
Check the specific gravity of each cell.
Standard specific gravity: At 20°C (68°F): 1.25 − 1.29
If the specific gravity is less than specification, charge the bat-
tery.
3. Maintenance−Free Battery:
CHECK BATTERY VOLTAGE
Measure the battery voltage between the negative (−) and posi-
tive (+) terminals of the battery.
Standard voltage: At 20°C (68°F): 12.7 − 12.9 V
HINT:
Before measuring the voltage, turn the ignition switch
OFF and turn off the electrical systems (headlight, blower
motor, rear defogger etc.) for 60 seconds to remove the
surface charge.

Downloaded from www.Manualslib.com manuals search engine P20582
Terminal F
CH−4
− CHARGING (5VZ−FE)CHARGING SYSTEM
1223 Author: Date:
1996 TOYOTA T100 (RM449U)
If the voltage reading is less than the standard voltage, check
the voltage regulator and generator as follows:
With terminal F grounded, start the engine and
check the voltage reading of terminal B.
If the voltage reading is higher than the standard
voltage, replace the voltage regulator.
If the voltage reading is less than the standard volt-
age, repair the generator.
9. INSPECT CHARGING CIRCUIT WITH LOAD
(a) With the engine running at 2,000 rpm, turn on the high
beam headlights and place the heater fan control switch
to HI.
(b) Check the reading on the ammeter.
Standard amperage: 30 A or more
If the ammeter reading is less than standard amperage, repair
the generator.
HINT:
If the battery is fully charged, the indication will sometimes be
less than standard amperage.

Downloaded from www.Manualslib.com manuals search engine Z17110
No continuity
Z17111
No continuity
Z17112No continuity
CL0363
Continuity
CL0364
No continuity CL−4
− CLUTCHCLUTCH PEDAL
1239 Author: Date:
1996 TOYOTA T100 (RM449U)
8. CHECK CONTINUITY OF CLUTCH START CANCEL
SWITCH
(a) Check that there is no continuity when connecting the
positive (+) lead from the ohmmeter to terminal 2 and the
negative (−) lead to terminal 1.
(b) Check that there is no continuity when connecting the
positive (+) lead from the ohmmeter to terminal 3 and the
negative (−) lead to terminal 1.
(c) Check the there is no continuity between terminals 2 and
3.
If continuity is not as specified, replace the clutch start cancel
switch.
9. CHECK OPERATION OF CLUTCH START CANCEL
SWITCH
(a) Connect positive (+) lead from the battery to terminal 3
and connect negative (−) lead to terminal 1.
(b) Check that there is no continuity when connecting the
positive (+) lead from the ohmmeter to terminal 2 and the
negative (−) lead to terminal 1.
(c) When pushing the switch, check that the indicator light
connect on and there is continuity between terminal 1 and
2.
(d) Check that there is no continuity between terminals 1 and
2 when disconnect the battery lead.
If continuity is not as specified, replace the clutch start cancel
switch.

Downloaded from www.Manualslib.com manuals search engine MT0501
Down
ClothCounterclockwise
MT04O−02
Q06817
Installation
Front
Select Return Spring
Tip of Shift Lever
− MANUAL TRANSMISSION (R150, R150F)MANUAL TRANSMISSION UNIT (4WD)
MT−7
1996 TOYOTA T100 (RM449U)
REMOVAL
1. REMOVE TRANSMISSION SHIFT LEVER
(a) Remove the 4 screws and front console box.
(b) Remove the 4 screws and shift lever boot retainer.
(c) Cover the shift lever cap with a cloth.
(d) Then, pressing down on the shift lever cap, rotate it coun-
terclockwise to remove.
(e) Pull out the shift lever.
HINT:
At the time of installation, please refer to the following item.
Apply MP grease to the tip of the shift lever.
2. REMOVE TRANSFER SHIFT LEVER
Using snap ring pliers, remove the snap ring and pull out the
shift lever.
HINT:
At the time of installation, please refer to the following item.
Apply MP grease to the tip of shift lever.
3. RAISE VEHICLE AND DRAIN TRANSMISSION OIL
Oil grade: API GL−4 or GL−5
Viscosity: SAE 75W−90
Capacity: 2.2 liters (2.3 US qts, 1.9 Imp. qts)
Torque: 37 N·m (380 kgf·cm, 27 ft·lbf)
4. REMOVE FRONT AND REAR PROPELLER SHAFTS
(See page PR−10)
5. DISCONNECT SPEEDOMETER CABLE
6. DISCONNECT BACK−UP LIGHT SWITCH AND 4WD
INDICATOR SWITCH CONNECTORS
7. DISCONNECT CLUTCH RELEASE CYLINDER AND
LINE
Remove the 4 bolts, release cylinder and line.
Torque: 12 N·m (120 kgf·cm, 9 ft·lbf)

Downloaded from www.Manualslib.com manuals search engine Q06824
Q06823
Q06822
Q10111
MT−8
− MANUAL TRANSMISSION (R150, R150F)MANUAL TRANSMISSION UNIT (4WD)
1996 TOYOTA T100 (RM449U)
8. REMOVE FRONT EXHAUST PIPE
(a) Remove the 2 nuts, gasket and oxygen sensor.
(b) Remove the 2 bolts, retainer and gasket.
Torque: 48 N·m (490 kgf·cm, 35 ft·lbf)
(c) Remove the 3 bolts and bracket.
Torque: 44 N·m (450 kgf·cm, 33 ft·lbf)
(d) Remove the 3 nuts, front exhaust pipe and 2 gaskets.
Torque: 62 N·m (630 kgf·cm, 46 ft·lbf)
9. REMOVE STARTER
(a) Disconnect the connector and wire from the starter.
(b) Remove the 2 bolts and starter.
Torque: 39 N·m (400 kgf·cm, 29 ft·lbf)
10. RE MO V E STIFFE NE R PLATE (RH AND LH) AND
REAR END PLATE
Remove the 8 bolts, stiffener plate (RH and LH) and rear end
plate.
Torque: 37 N·m (380 kgf·cm, 27 ft·lbf)
11. REMOVE STABILIZER BAR (See page SA−126)
12. JACK UP TRANSMISSION SLIGHTLY
Using a transmission jack, support the transmission.
13. REMOVE CROSSMEMBER
(a) Remove the 4 set bolts of the engine rear mounting.
Torque: 13 N·m (130 kgf·cm, 9 ft·lbf)
(b) Remove the 8 bolts and crossmember.
Torque: 95 N·m (970 kgf·cm, 70 ft·lbf)
14. REMOVE TRANSMISSION WITH TRANSFER
(a) Remove the 6 transmission mounting bolts from the en-
gine.
Torque: 72 N·m (730 kgf·cm, 53 ft·lbf)
(b) Disconnect the 3 wire clamps from the transmission.
(c) Pull out the transmission with the transfer down and to-
ward the rear.
15. REMOVE ENGINE REAR MOUNTING
Remove the 4 bolts and engine rear mounting.
Torque: 25 N·m (250 kgf·cm, 18 ft·lbf)

Downloaded from www.Manualslib.com manuals search engine MT04R−01
Q06902
FIPG
− MANUAL TRANSMISSION (R150, R150F)MANUAL TRANSMISSION ASSEMBLY
MT−13
1996 TOYOTA T100 (RM449U)
DISASSEMBLY
1. REMOVE BACK−UP LIGHT SWITCH
Torque: 44 N·m (450 kgf·cm, 32 ft·lbf)
2. 2WD:
REMOVE SPEEDOMETER DRIVEN GEAR
Remove the driven gear lock plate set bolt and driven gear.
Torque: 11 N·m (115 kgf·cm, 8 ft·lbf)
3. REMOVE CLUTCH HOUSING FROM TRANSMISSION
CASE
Remove the 9 bolts and clutch housing from the transmission
case.
Torque: 36 N·m (370 kgf·cm, 27 ft·lbf)
4. REMOVE CONTROL SHIFT LEVER RETAINER
(a) Remove the 6 (2WD) or 4 (4WD) bolts.
Torque: 18 N·m (185 kgf·cm, 13 ft·lbf)
(b) Remove the retainer and gasket (2WD) or oil deflector
(4WD).
5. REMOVE 2 RESTRICT PINS
Torque: 37 N·m (380 kgf·cm, 27 ft·lbf)
6. 2WD:
REMOVE EXTENSION HOUSING
(a) Remove the shift lever housing set bolt.
Torque: 38 N·m (390 kgf·cm, 28 ft·lbf)
(b) Remove the 10 bolts.
Torque: 37 N·m (380 kgf·cm, 27 ft·lbf)
(c) Using a plastic hammer, tap the extension housing, re-
move the shift lever housing and shift and select lever.
FIPG:
Part No. 08826 − 00090, THREE BOND 1281 or
equivalent

Downloaded from www.Manualslib.com manuals search engine Q00550
MT04U−01
Z03541
− MANUAL TRANSMISSION (R150, R150F)INPUT SHAFT
MT−23
1996 TOYOTA T100 (RM449U)
INSPECTION
INSPECT SYNCHRONIZER RING
(a) Check for wear or damage.
(b) Check the braking effect of the synchronizer ring.
Turn the synchronizer ring in one direction while pushing
it to the gear cone. Check that the ring locks.
If the braking effect is insufficient, apply a small amount of the
fine lapping compound between the synchronizer ring and gear
cone. Lightly rub the synchronizer ring and gear cone together.
NOTICE:
Ensure the fine lapping compound is completely washed
off after rubbing.
(c) Check again the braking effect of the synchronizer ring.
(d) Using a feeler gauge, measure the clearance between
the synchronizer ring back and gear spline end.
Minimum clearance: 0.8 mm (0.031 in.)
If the clearance is less than the minimum, replace the synchro-
nizer ring, and apply a small amount of the fine lapping com-
pound on gear cone.
NOTICE:
Ensure the fine lapping compound is completely washed
off after rubbing.

Downloaded from www.Manualslib.com manuals search engine Z03554
MT04Y−05
Z03555
AB
C
Z03556
WM0064
MT−28
− MANUAL TRANSMISSION (R150, R150F)OUTPUT SHAFT
1996 TOYOTA T100 (RM449U)
INSPECTION
1. INSPECT OUTPUT SHAFT
(a) Using a micrometer, measure the output shaft flange
thickness.
Minimum thickness: 4.70 mm (0.1850 in.)
If the thickness is less than the minimum, replace the output
shaft.
(b) Using a micrometer, measure the outer diameter of the
output shaft journal.
Minimum diameter:
A 1st gear: 38.860 mm (1.5299 in.)
B 2nd gear: 46.860 mm (1.8449 in.)
C 3rd gear: 37.860 mm (1.4905 in.)
If the outer diameter is less than the minimum, replace the out-
put shaft.
(c) Using a dial indicator, check the shaft runout.
Maximum runout: 0.06 mm (0.0024 in.)
If the runout exceeds the maximum, replace the output shaft.
2. INSPECT 1ST AND 3RD GEARS SYNCHRONIZER
RING
(a) Check for wear or damage.
(b) Check the braking effect of the synchronizer ring.
Turn the synchronizer ring in one direction while pushing
it to the gear cone. Check that the ring locks.
If the braking effect is insufficient, apply a small amount of the
fine lapping compound between the synchronizer ring and gear
cone. Lightly rub the synchronizer ring and gear cone together.
NOTICE:
Ensure the fine lapping compound is completely washed
off after rubbing.
(c) Check again the braking effect of the synchronizer ring.

Downloaded from www.Manualslib.com manuals search engine MT03M−03
Z15702
Clutch Housing Cover
Snap Ring
Transmission Case
Front Bearing
Clutch HousingFiller Plug Drain Plug Retainer
Release
Fork Support
Straight Screw Plug
Intermediate PlateOutput Shaft
Locking Ball

x 7 x 9
BootBack−Up
Light Switch
Restrict PinControl Shift Lever
Retainer
Oil Baffle Plate
Restrict Pin
Extension Housing Speedometer Driven Gear
Non−reusable part
Precoated partInput Shaft
x 6
x 9Straight Screw Plug
Spring 
 

Gasket
Gasket Gasket
Gasket
Gasket

39 (400, 29)
MT−6
− MANUAL TRANSMISSION (W59)MANUAL TRANSMISSION ASSEMBLY
1305 Author: Date:
1996 TOYOTA T100 (RM449U)
MANUAL TRANSMISSION ASSEMBLY
COMPONENTS