key VOLKSWAGEN JETTA 1998 Manual PDF

Downloaded from www.Manualslib.com manuals search engine 01-245



Test sequence and test tables with
measured values

Checking speed sensor allocation

Display group number 001

- Press keys 0, 0 and 1.

- Confirm entry with key Q.
Read measured value block
1
1 2 3 4
- There are always 4 display zones -
arrows- in the measured value block.
Decoding the individual values in display
zones 1 to 4 can be read-off from the
following tables.
Read measured value block 1
0 km/h 0 km/h 0 km/h 0 km/h
Indicated on display: (vehicle stationary)
Press C key for the next display group
number entry.
If the key is pressed, keys 0 and 8 for
work sequence "Read measured value
block" must be pressed again afterwards to
regain entry.
Стр. 87из 129 On Board Diagnostic (OBD), performing

Downloaded from www.Manualslib.com manuals search engine 01-247



Checking speed sensor

Display group number 002

- Press keys 0, 0 and 2.

- Confirm entry with key Q.
Read measured value block
2
1 2 3 4
- There are always 4 display zones -
arrows- in the measured value block.
Decoding the individual values in display
zones 1 to 4 can be read-off from the
following tables.
Read measured value block
2
255 km/h 255 km/h 255 km/h 255 km/h
Indicated on display: (vehicle stationary)
Press C key for the next display group
number entry.
If the key is pressed, keys 0 and 8 for
work sequence "Read measured value
block" must be pressed again afterwards to
regain entry.
Стр. 89из 129 On Board Diagnostic (OBD), performing

Downloaded from www.Manualslib.com manuals search engine 01-249



Checking brake light switch, brake
system warning lamp, ABS warning
lamp and ASR/ESP warning lamp

Display group number 003

- Press keys 0, 0 and 3

- Confirm entry with key Q.
Read measured value block
3
1 2 3 4
- There are always 4 display zones -
arrows- in the measured value block.
Decoding the individual values in display
zones 1 to 4 can be read-off from the
following tables.
Read measured value block
3
not oper. off off off
Indicated on display: (vehicle stationary)
Press C key for the next display group
number entry.
If the key is pressed, keys 0 and 8 for
work sequence "Read measured value
block" must be pressed again afterward to
regain entry.
Стр. 91из 129 On Board Diagnostic (OBD), performing

Downloaded from www.Manualslib.com manuals search engine 01-251



Checking steering angle sensor, sensor
for transverse acceleration and sender
for rotation rate
1)

Display group number 004

- Press keys 0, 0 and 4

- Confirm entry with key Q.
Read measured value block
4
1 2 3
- There are always 3 display zones -
arrows- in the measured value block.
Decoding the individual values in display
zones 1 to 3 can be read-off from the
following tables.
Read measured value block
4
0.0 0.0m/s2- 1.26/s
Indicated on display: e.g. (vehicle
stationary)
Press C key for the next display group
number entry.
If the key is pressed, keys 0 and 8 for
work sequence "Read measured value
block" must be pressed again afterwards to
regain entry.
1) For ABS/EDL/ASR/ESP and
ABS/EDL/ASR/ESP 4MOTION only
Стр. 93из 129 On Board Diagnostic (OBD), performing

Downloaded from www.Manualslib.com manuals search engine 01-255



Checking brake pressure sensor 1)

Display group number 005

- Press keys 0, 0 and 5

- Confirm entry with key Q.
Read measured value block
5
1 2 3 4
- There are always 4 display zones -
arrows- in the measured value block.
Decoding the individual values in display
zones 1 to 4 can be read-off from the
following tables.
Read measured value block
5
- 1.06 bar
Indicated on display: e.g. (vehicle
stationary)
Press C key for the next display group
number entry.
If the key is pressed, keys 0 and 8 for
work sequence "Read measured value
block" must be pressed again afterwards to
regain entry.
1) For ABS/EDL/ASR/ESP and
ABS/EDL/ASR/ESP 4MOTION only
Стр. 97из 129 On Board Diagnostic (OBD), performing

Downloaded from www.Manualslib.com manuals search engine 01-257



Checking longitudinal acceleration
sensor -G251-
1)

Display group number 006

- Press keys 0, 0 and 6

- Confirm entry with key Q.
Read measured value block
6
1 2 3 4
- There are always 4 display zones -
arrows- in the measured value block.
Decoding the individual values in display
zones 1 to 4 can be read-off from the
following tables.
Read measured value block
6
0.0m/s2
Indicated on display: (vehicle stationary)
Press C key for the next display group
number entry.
If the key is pressed, keys 0 and 8 for
work sequence "Read measured value
block" must be pressed again afterwards to
regain entry.
1) For 4MOTION vehicles only
Стр. 99из 129 On Board Diagnostic (OBD), performing

Downloaded from www.Manualslib.com manuals search engine 01-261



Checking data bus wiring

Display group number 125

- Press keys 1, 2 and 5

- Confirm entry with key Q.
Read measured value block
125
1 2 3 4
- There are always 4 display zones -
arrows- in the measured value block.
Decoding the individual values in display
zones 1 to 4 can be read-off from the
following tables.
Read measured value block 125
Engine 1 St.ang. 1 4WD 1 Gear.1
Indicated on display: (vehicle stationary)
Press C key for the next display group
number entry.
If the key is pressed, keys 0 and 8 for
work sequence "Read measured value
block" must be pressed again afterwards to
regain entry.
Стр. 103из 129 On Board Diagnostic (OBD), performing

Downloaded from www.Manualslib.com manuals search engine 01-266



Display group number 01: Bleeding
hydraulic unit

Special tools and equipment

Note:
All functions which could previously be
performed with V.A.G 1551 can now also
be carried out with the tester VAS 5051.
Repair Manual, Brake System, Repair
Group 47; Bleeding brake system, vehicles
with and without ABS
VAS 5234 Brake filler and bleeder unit
- Connect brake filling and bleeder unit
VAS 5234.
- Pre-bleed brake system
- Connect V.A.G 1551 scan tool and select
(address word 03) brake electronics
control module with ignition switched on;
Page 01
-163 .
Rapid data transfer HELP
Select function XX Indicated on display
- Press keys 0 and 4. (The function
"Initiating basic setting" is selected with
04).
Стр. 108из 129 On Board Diagnostic (OBD), performing

Downloaded from www.Manualslib.com manuals search engine 01-267


Rapid data transfer Q
04 - Basic settin
g
Indicated on display:
- Confirm entry with key Q.
Basic setting HELP
Enter dis
play group number XXX
Indicated on display:
The following cycle of steps must be
repeated 8 times according to the basic
setting prescribed by V.A.G 1551 or
tester VAS 5051. - Press keys 0, 0 and 1
- Confirm entry with key Q.
Basic setting 1 ON
De
press pedal and hold...
Indicated on display:
- Operate pedal with substantial foot
pressure and hold.
Pedal moves down
Hydraulic pump runs
Pedal comes back
Basic setting 1
Rel. pedal; FR/FL bleed screw OPEN Indicated on display:
- Press key 3 on V.A.G 1551 or arrow up
key on VAS 5051
Basic setting 1 ON
Please wait...
(10 secs.)
Indicated on display:
Hydraulic pump runs
Стр. 109из 129 On Board Diagnostic (OBD), performing

Downloaded from www.Manualslib.com manuals search engine 01-268


Basic setting 2
De
pr. pedal 10X; bleed screw CLOSED
Indicated on display:
- Press key 3 on V.A.G 1551 or arrow up
key on VAS 5051
System in basic setting 17
Part. bleedin
g ended...
When all 8 cycles have been performed,
this message appears on the display:
-
Press key.
Rapid data transfer HELP
Select function XX Indicated on display:
- Press keys -0- and -6-, this ends the
output.
Rapid data transfer Q
06 - End output Indicated on display
- Confirm entry with Q key
Rapid data transfer Help
Enter address word XX
Indicated on display
Repair Manual, Brake System, Repair
Group 47; Bleeding brake system, vehicles
with and without ABS - Press C key
- Switch off ignition.
- Disconnect connection to V.A.G 1551
scan tool.
- Bleed brake system again
For vehicles with ABS/EDL/ASR/ESP:
perform zero compensation for Sender
1 for brake booster -G201- Page 01
-
278 .
Стр. 110из 129 On Board Diagnostic (OBD), performing