washer VOLKSWAGEN PASSAT 1996 B3, B4 / 3.G Service Owner's Manual

Downloaded from www.Manualslib.com manuals search engine 42-28

26 - Dished washer Large contact surface
(concave side) to
backing plate
27 - Backing plate
28 - Axle beam Straightening work is
not permissible! Only
use stub axles with 6
mounting holes.
29 - Parking brake cable Adjusting parking
brake Page 46-36 30 - Spring clip Page 14 of 18Wheel bearings, servicing12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.42.2

Downloaded from www.Manualslib.com manuals search engine 42-30
Note: Fig. 3 Grease cap, driving on Always replace damaged (dented) grease caps. Damaged (dented) grease caps allow ingress of
moisture, therefore always use the illustrated tool. Note:
Using a screwdriver it must be possible to move the
thrust washer by finger pressure (without prying). Fig. 4 Wheel bearing play, adjusting - Secure with locking ring and new cotter pin. Page 16 of 18Wheel bearings, servicing12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.42.2

Downloaded from www.Manualslib.com manuals search engine 42-47

1 - Circlip Always replace Remove and install
with VW161 a
2 - Inner constant velocity
joint, 81 mm diameter Only replace complete Pressing off Page 40-54 Pressing on Page 40-55 Greasing Notes
Page 42-46 Checking Page 40-62 3 - Dished washer Inner diameter splined Installation position:
outer diameter
(concave side)
contacts constant
velocity joint Page 2 of 7Rear drive shafts, servicing12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.42.4

Downloaded from www.Manualslib.com manuals search engine 42-49

7 - Boot for 81 mm
diameter constant
velocity joint Polyester elastomer
version Check for tears and
chafing Installation position: At
cuff 1 to 1-1/2 grooves
visible To balance pressure
briefly ventilate boot
before tensioning the
small clamp
8 - Hose clamp Always replace Tensioning Page 40-57 9 - Dished washer Outer diameter
(concave side)
contacts thrust washer
10 - Thrust washer Page 4 of 7Rear drive shafts, servicing12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.42.4

Downloaded from www.Manualslib.com manuals search engine 42-52

- Cut new thread in the cap nut, M 12 x 1.5.
- Use new bolts, Part No. N 010 137.1 and
washer, Part No. N 011 531.7 to secure the rear
axle.
Tightening torque: 65 Nm (48 ft lb)

Note:
The procedure described here must only be
performed on one cap nut on each side of the
vehicle. Page 7 of 7Rear drive shafts, servicing12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.42.4

Downloaded from www.Manualslib.com manuals search engine 42-53

Suspension strut,
disassembling and
assembling (four
wheel drive
vehicles)
1 - Cap Pry out with
screwdriver Pressing on Fig. 5 Installation position
Fig. 5 2 - Seal
3 - Self locking hex nut, 30 Nm (22 ft lb) Always replace 4 - Dished washer
5 - Upper rubber mounting 6 - Gasket (foam) Always replace Page 1 of 6Suspension strut, disassembling and assembling (four wheel drive vehicles)12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.42.5

Downloaded from www.Manualslib.com manuals search engine 42-54

7 - Suspension strut
mounting Welded nuts must be
located in the spring
seat recesses Installation position to
spring seat Fig. 3 8 - Spring seat
9 - Spacer tube
10 - Lower rubber
mounting
11 - Stop buffer mounting
12 - Washer
13 - Stop buffer
14 - Ring (Aluminium)
15 - Boot
16 - Protective cap Page 2 of 6Suspension strut, disassembling and assembling (four wheel drive vehicles)12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.42.5

Downloaded from www.Manualslib.com manuals search engine 46-15

Rear wheel brakes,
servicing (drum
brakes)
Notes Page 42-15 1 - Grease cap Removing and
installing from
Page 42-19 2 - Cotter pin Always replace 3 - Locking ring
4 - Hex nut Adjusting wheel
bearing play Page 42-20 5 - Thrust washer Page 1 of 4Rear wheel brakes, servicing (drum brakes)12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.46.3

Downloaded from www.Manualslib.com manuals search engine 46-17

10 - Hex socket head bolt,
10 Nm (7 ft lb)
11 - Wheel speed sensor Only on vehicles with
ABS Insert with lubricating
paste, G 000 650
12 - Backing plate with
brake shoes Release adjustment
before removing brake
drum Page 46-18 13 - Dished washer Large contact surface
faces back plate
14 - Hex bolt, 60 Nm (44 ft
lb) Page 3 of 4Rear wheel brakes, servicing (drum brakes)12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.46.3

Downloaded from www.Manualslib.com manuals search engine 46-30

14 - Outer wheel bearing
15 - Hex nut Adjusting wheel
bearing play Using a screwdriver it
must be possible to
move the thrust
washer by finger
pressure (without
leverage) Page 42-20 Secure with locking
ring and new cotter pin 16 - Cotter pin Always replace 17 - Grease cap Removing and
installing Page 42-29 18 - Lock ring
19 - Thrust washer
20 - Wheel bolt, 110 Nm (81
ft lb) Page 4 of 10Rear wheel brakes, servicing (disc brakes)12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.46.5