lock VOLVO S60 2009 Owner´s Manual

02 Instruments and controls
Lighting panel
02``59
3501866mG027132
Headlight/parking light switchFront fog lightsRear fog lightInstrument panel lightingFuel filler door unlock button
Parking lightsThe front and rear parking lights can be turned
on even when the ignition is switched off.•
Turn switch (1) to position
.
The license plate lights also illuminate when the
parking lights are switched on.
Headlights±
Turn the ignition key to position II.
The low beam headlights (daytime running
lights) illuminate automatically, except when
the light switch (1) is in position.
1
See page 62 for information on switching
between high and low beams.
NOTE
Active Bi-Xenon headlights (option): Turn
the headlight switch to position 0 to activate
a daylight sensor, which automatically
switches the low beams on or off, depend-
ing on ambient light conditions. When driv-
ing in daylight, the headlights will switch off
and the daytime running lights will come on.
In darkness, the daytime running lights will
switch off and the Active Bi-Xenon head-
lights will switch on.
Active Bi-Xenon headlights (ABL) -
option
G020789
Active Bi-Xenon headlight beamsWhen the ABL function is activated, the head-
light beams adjust laterally to help light up a
curve according to movements of the steering
wheel (see the right-pointing beam in the illus-
tration above).
This function is activated automatically when
the engine is started and can be deactivated/
reactivated by pressing the ABL button (see
page 57).
1On Canadian models, the daytime running lights will remain on with the light switch in this position.

02 Instruments and controlsLighting panel
0260
Fog lightsFront fog lights (option)The front fog lights can be used in combination
with either the headlights or the parking lights.•
Turn the ignition key to position II.
•
Press button 2 to turn on the front fog
lights.
An indicator light in the button illuminates when
the front fog lights are on.
Rear fog lightThe single rear fog light is located in the driver's
side tail light cluster.
The rear fog light will only function in combi-
nation with the high/low beam headlights or the
optional front fog lights.•
Turn the ignition key to position II.
•
Press button 3 to turn on the rear fog light.
An indicator light in the button illuminates when
the rear fog light is on.NOTE
The rear fog light is considerably brighter
than the normal taillights and should be
used only when conditions such as fog, rain,
snow, smoke or dust reduce visibility for
other vehicles to less than 500 ft.
(150 meters).
Instrument panel lightingThe instrument panel lighting illuminates when
the ignition key is in position IIand the light
switch (1) is in either position
or
.
•
Move the thumb wheel (4) up to increase
brightness or down to decrease bright-
ness.
Unlocking the fuel filler doorPress button 5 when the vehicle is at a stand-
still to unlock the fuel filler door. Please note
that the fuel filler door will remain unlocked until
the vehicle begins to move forward. An audible
click will be heard when the fuel filler door
relocks.
NOTE
If the fuel filler door does not unlock after the
button has been pressed, drive the vehicle
at a speed of at least 5 mph (8 km/h), stop
the vehicle, and press the button again.See page 61 for information on unlocking the
fuel filler door manually.

02 Instruments and controls
Fuel filler door–unlocking manually
0261 Manually unlocking the fuel filler door
G027212
The electric motor that controls the fuel filler
door locking mechanism is located on the
inside of the rear fender on the passenger side
of the vehicle, just behind the fuel filler door. To
unlock this door manually:
1. Turn the knob 1/4 turn counterclockwise to
release the cover panel.
2. Fold down the cover panel to access the
electric motor.
3. Press the catch rearward to unlock the fuel
filler door, or forward to lock the door.

02 Instruments and controlsLeft-side steering wheel lever
0262
Lever positions
G027178
Turn signals, lane change positionTurn signals, position for normal turnsHigh beam flashToggle between high and low beams,
Home Safe lighting
Turn signalsWhen changing lanesThe driver can automatically flash the turn sig-
nals 3 times by moving the turn signal lever up
or down to position 1 and releasing it.
NOTE
This automatic flashing sequence can be
interrupted by immediately moving the lever
in the opposite direction.
If the turn signal indicator flashes faster than
normal, check for a burned-out turn signal
bulb.When turningMove the lever as far up or down as possible
(to position 2) to start the turn signals. The turn
signals will be cancelled automatically by the
movement of the steering wheel, or the lever
can be returned to its initial position by hand.
High/low beam headlightsContinuous high beams1.
Turn the ignition key to position II.
2. With the light switch (1) in position, (see
page 59) pull the turn signal lever toward
the steering wheel (position 4) to toggle
between high and low beams (this also
applies on models equipped with the
optional Active Bi-Xenon headlights).High beam flash1.
Turn the ignition key to position II.
2. Pull the turn signal lever to position 3.
> The high beams will remain on until the
lever is released.Home safe lightingWhen you leave your vehicle at night, you can
make use of the home safe lighting function to
illuminate the area in front of the vehicle.
1. Remove the key from the ignition switch.
2. Pull the direction indicator lever as far as
possible towards the steering wheel (to
position 4) and release it.
3. Exit the vehicle and lock the doors.

02 Instruments and controlsCruise control
0270
NOTE
Cruise control is automatically disengaged
if:•
the engine is switched off
•
the gear selector is placed in (N)eutral
•
the wheels start to spin or lock
•
if an increase in speed is maintained for
more than one minute
•
if the vehicle's speed falls below
approximately 20 mph (30 km/h).
Temporarily disengaging cruise control1.
Press0 to temporarily disengage cruise
control.
>
CRUISE
will be displayed in the infor-
mation window in the instrument panel.
2. Press the brake pedal.
Press resume (see illustration) to return to the
previously set speed.
WARNING
Cruise control should not be used in heavy
traffic or when driving on wet or slippery
roads, or when driving on unpaved or
uneven road surfaces. Cruise control may
not maintain set speed on steep down-
grades.

02 Instruments and controlsPower windows
0274
If the LED in the switch is OFFThe rear door windows can be raised or low-
ered with the buttons on the rear door armrests
or with the buttons on the driver's door arm-
rest.If the LED in the switch is ONThe rear door windows can only be raised or
lowered with the buttons on the driver's door
armrest.Power window on the front
passenger's side
G029585
The control for the electrically operated win-
dow in the front passenger's seat operates that
window only.
Power windows in the rear doors
G029586
The rear door windows can be operated with
the control on each door and the switch on the
driver's door. If the LED in the switch for block-
ing electrically operated windows in the rear
doors (located in the driver's door control
panel) is on, the rear door windows can only be
operated from the driver's door.

02 Instruments and controls
Mirrors
0277
After you have adjusted the mirror(s), press the
L or R switch again (the LED will go out) to
deactivate the adjustment control.
WARNING
The mirrors should always be adjusted prior
to driving. Objects seen in the passenger's
side wide-angle door mirror are closer than
they appear to be.Remote central locking and door mirror
memory–optionIf you lock the vehicle and later unlock it with
thesame remote control and open the driver's
door, the door mirrors (and the driver's seat)
will automatically move to the position they
were in when you left the vehicle. This feature
will work in the same way with all of the remote
control transmitters (up to 3) that you use with
your vehicle. This feature will not function if you
lock your vehicle with the key.

02 Instruments and controlsHomeLink® Wireless Control System (option)
0280
Introduction
G030070
The HomeLink Wireless Control System pro-
vides a convenient way to replace up to three
hand-held radio-frequency (RF) transmitters
used to activate devices such as gate opera-
tors, garage door openers, entry door locks,
security systems, even home lighting. Addi-
tional HomeLink information can be found on
the Internet at www.homelink.com.
WARNING
•
If you use HomeLink to open a garage
door or gate, be sure no one is near the
gate or door while it is in motion.
•
When programming a garage door
opener, it is advised to park outside of
the garage.
•
Do not use HomeLink with any garage
door opener that lacks safety stop and
reverse features as required by U.S.
federal safety standards (this includes
any garage door opener model manu-
factured before April 1, 1982). A garage
door that cannot detect an object - sig-
naling the door to stop and reverse -
does not meet current U.S. federal
safety standards. For more information,
contact HomeLink at:
www.homelink.com.
Retain the original transmitter of the RF device
you are programming for use in other vehicles
as well as for future HomeLink programming. It
is also suggested that upon the sale of the
vehicle, the programmed HomeLink buttons be
erased for security purposes. Refer to “Erasing
HomeLink Buttons”.
Programming HomeLink
NOTE
Some vehicles may require the ignition
switch to be turned on or to the second
(“accessories”) position for programming
and/or operation of HomeLink. It is also rec-
ommended that a new battery be placed in
the hand-held transmitter of the device
being programmed to HomeLink for quicker
training and accurate transmission of the
radio-frequency signal.1. Position the end of your hand-held trans-
mitter 1–3 inches (5–14 cm) away from the
HomeLink button you wish to program
while keeping the indicator light in view.
2. Simultaneously press and hold both the
chosen HomeLink and hand-held transmit-
ter buttons until the HomeLink indicator
light changes from a slow to a rapidly blink-
ing light. Now you may release both the
HomeLink and hand-held transmitter but-
tons.

02 Instruments and controls
HomeLink® Wireless Control System (option)
02``81
NOTE
Some devices may require you to replace
this Programming Step 2 with procedures
noted in the “Gate Operator / Canadian Pro-
gramming” section. If the HomeLink indica-
tor light does not change to a rapidly
blinking light after performing these steps,
contact HomeLink at www.homelink.com.3.
Firmlypress, hold for five seconds and
release the programmed HomeLink but-
ton up to two separate times to activate the
door. If the door does not activate, press
and hold the just-trained HomeLink button
and observe the indicator light.
•If the indicator light stays on con-
stantly, programming is complete
and your device should activate when
the HomeLink button is pressed and
released.•If the indicator light blinks rapidly for
two seconds and then turns to a con-
stant light continue with “Program-
ming” steps 4-6 to complete the pro-
gramming of a rolling code equipped
device (most commonly a garage door
opener).
4. At the garage door opener receiver (motor-
head unit) in the garage, locate the “learn”
or “smart” button. This can usually befound where the hanging antenna wire is
attached to the motor-head unit.
5. Firmly press and release the “learn” or
“smart” button. (The name and color of the
button may vary by manufacturer.) There
are 30 seconds to initiate step 6.
6. Return to the vehicle and firmly press, hold
for two seconds and release the pro-
grammed HomeLink button. Repeat the
“press/hold/release” sequence a second
time, and, depending on the brand of the
garage door opener (or other rolling code
equipped device), repeat this sequence a
third time to complete the programming
process.
HomeLink should now activate your rolling
code equipped device.
Gate Operator/Canadian ProgrammingCanadian radio-frequency laws require trans-
mitter signals to “time-out” (or quit) after sev-
eral seconds of transmission – which may not
be long enough for HomeLink to pick up the
signal during programming. Similar to this
Canadian law, some U.S. gate operators are
designed to “time-out” in the same manner.
If you live in Canada or you are having difficul-
ties programming a gate operator or garage
door opener by using the “Programming” pro-cedures,replace “Programming HomeLink”
step 2 with the following:
•
Continue to press and hold the HomeLink
button while you press and release -
every two seconds (“cycle”) your hand-
held transmitter until the HomeLink indica-
tor light changes from a slow to a rapidly
blinking light. Now you may release both
the HomeLink and hand-held transmitter
buttons.
Proceed with “Programming” step 3 to com-
plete.
Using HomeLinkTo operate, simply press and release the pro-
grammed HomeLink button. Activation will
now occur for the trained device (i.e., garage
door opener, gate operator, security system,
entry door lock, home/office lighting, etc.). For
convenience, the hand-held transmitter of the
device may also be used at any time. In the
event that there are still programming difficul-
ties or questions, contact HomeLink at:
www.homelink.com.

03 ClimateElectronic climate control, ECC
0390
Blower control
Turn the control clockwise to
increase or counterclockwise
to decrease the blower
speed. Pressing the AUTO
switch will automatically reg-
ulate blower speed and over-
ride manual adjustment.
Turning the blower control counterclockwise
until an orange LED comes on will turn both the
blower and the air conditioning off.Air distributionAir flow to windows
Air through panel vents
Air through floor vents
G027267
PressAUTO to automatically regulate air flow
or press any combination of the controls
shown in the illustration to manually adjust air
flow. An LED in the switch will light up if an air
flow control has been pressed.Heated front seats (option)•
Press the switch once for maximum seat
heating. Both LEDs in the switch will be lit.
•
Press the switch a second time for comfort
heating. One LED in the switch will be lit.
•
Press the switch a third time to turn the
heating off completely. The LED will go off.
The seat heating for the passenger seat should
be switched off when the seat is not occupied.
A/C - ON/OFF
Press the switch to turn the air
conditioning on or off. The
"ON" or "OFF" LED will light up
to indicate if the system is
switched on or off. Other func-
tions will still be regulated auto-
matically (if the AUTO switch is on).
•
The air conditioning functions only at tem-
peratures above 32 °F (0 °C).
•
While the Defroster function is selected,
the air conditioning is temporarily activated
to dehumidify the air, even if you have man-
ually switched the air conditioning off. This
will only function if the blower is not
switched off.
Recirculation
Press this switch to engage the
recirculation function (air in the
passenger compartment recir-
culates - no fresh air enters the
compartment). The LED in the
switch will light up to indicate
that the function is engaged.
MANAUT€
Use this function if the outside air is con-
taminated with exhaust gases, smoke, etc
or to heat/cool the vehicle quickly.
€
Recirculation should not be used for more
than 15 minutes. If your windows begin to
fog or mist, make sure that the recirculation
function is switched off.
€
SelectingDefroster automatically
switches recirculation off.